Search Documents

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By H. Foster Bain

The war has brought about many changes in the Western States, and some have deep pr sent or potent al economic significance. The West has been feeling severe growing pains for a number of years. Especially since the beginning of preparation for national defense and through the period of

Jan 1, 1945

This report presents production and delivered costs for coal exports from the five major Western coal-exporting countries: Australia, Canada. Colombia, South Africa, and the United States. Cost data were compiled from visits to 43 mines by U.S. Bureau of Mines engineers between 1985 and 1990. All report costs are in January 1989 U.S. dollars per short ton. Production costs for raw coal are divided into mining and regulatory categories. Costs are broken down by type of cost, type of mine. and country. Scheduled operating and capital costs for raw coal were processed by the Bureau's MINSIM discounted cash flow program to determine total production costs calculated at 0% and 15% discounted cash flow rates of return (DCFROR). Delivered costs are for salable coal delivered to various markets. Costs are broken down by supply country, market, and type of cost. Scheduled operating and capital costs for salable coal were processed by the Bureau's MINSIM discounted cash-flow program to determine total salable coal costs at 0% DCFROR. Added to total salable coal costs were transportation and port costs to get delivered costs. Comparative overview information on the coal industries of the five study countries are appended. This appendix includes information on industry economics and exports, production and reserves, and coal industry issues.

Jan 1, 1993

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

Ground-water and tailings pond monitoring in the Upper Santa Cruz Basin Mines Task Force's Special Studies Area has been performed to determine the nature and extent of aquifer contamination from copper tailings pond's recharge in the basin. A monitoring program for each of three mining areas (Mines A, B, and D) was developed. Analysis of data shows that recharge from Mine A's ponds has caused increased hardness, sulfate and total dissolved solids in local ground water. However, pumpage in the area has controlled most of the water's movement. Pond recharge from Mine B has led to similar conditions, and the degraded water is moving towards a local public-supply well. Pumpage from Mine D's interceptor wells is controlling some, but not all, of the movement of recharge seepage from Mine D's ponds. Recommendations include the need for enhanced monitoring programs at each current mine site, development of a monitoring program for Mine C's area, development of water budgets for all mines, investigation of tailings pond compaction and sliming, establishment of mine closure plans for containment of recharged pond water, and the need for additional interceptor wells in several locations.

Jan 1, 1983

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in August 1983 for the purpose of disseminating recent advances in mining technology in the area of large mobile surface mining equipment safety and health. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1983

By James L. Elder, J. P. Capp, James J. Dowd

The Bureau of Mines and the Alabama Power Co., jointly, conducted the first experiment undertaken in the United States in underground gasification of coal in place, at Gorgas, Ala. Milton H. Fies, manager of coal operations, Alabama Power Co., proposed the cooperative investigation to Arno C. Fieldner, chief, Fuels and Explosives Branch, Bureau of Mines; and assisted in supervising the experiment. The objectives of the experiment were to determine whether coal in place could be burned successfully and whether the burning could be controlled; the effect of the fire on the coal bed and the overlying strata; and the yield and quality of gas that could be obtained.

Aug 1, 1947

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized- bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could be incorporated in design, installation, and operation to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized- bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on heated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or "bumps" had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By Hylton R. Brown

This publication, an abstract of a progress report covering an investigation of hazards in thermal coal-drying plants has been prepared according to the suggestions and recommendations of a committee6/ appointed by J. J. Forbes, Director of the Bureau of Mines, when the original report was reviewed at a meeting of representatives of the mining industry, operators of coal-drying plants, coal-mine workers, and the Bureau in Washington on May 6, 1955. The investigation on which the report is based was made in accordance with action taken at a previous conference in Washington on May 19, 1954, called by Director Forbes to consider what should be done to prevent explosions and fires in coal-drying plants. Scope of Investigation The investigation was planned to obtain information considered essential for properly appraising fire and explosion hazards in different types of coal driers. A questionnaire sent to Bureau personnel provided preliminary information on coal-drying facilities at more than 270 preparation plants. Information on methods used in operating different types of driers, with their furnaces, fans, cyclones, and other auxiliary equipment, was obtained by personal visits or conferences with the operators at 13 plants. Factual data on operating temperatures, composition of the drying gases, air flow, dust loading of the air or gas currents, use of water sprays, auxiliary air controls, and other factors were obtained by conducting full-scale tests at six different plants and making laboratory investigations with samples of dust and gas collected during the tests.

Jan 1, 1956

By William H. Pailes, Vincent Castronova, Daniel Lewis, Norman L. Lapp, George Goodman

"INTRODCJCTIONAlveolar macrophages are free lung cells located on the surface of small airways and alveoli. These phagocytes play an important role in the protection of the lung against airborne bacteria and particles.1 However, hyperactivation of pulmonary phagocytes can lead to excessive secretion of enzymes and reactive oxygen species which could result in lung injury, emphysema, or fibrosis.2,3 Analysis of bronchoalveolar lavage effluents for cell types and cellular activity has yielded information concerning the etiology of various pneumoconioses. For example, emphysema associated with inhalation of coal dust or cigarette smoke has been related to enhanced secretion of reactive oxygen species from alveolar macrophages.4-7 In contrast, hypoactivation of alveolar macrophages has been associated with inhalation of diesel particulates"" and has been related to increased susceptibility to pulmonary infection. s Inhalation of cotton dust has been associated with dramatic increases in lavagable polymorphonuclear leukocytes9 while pulmonary sarcoidosis and silicosis have been related with high numbers of lymphocytes in lavage effluentsl0,11The objective of the present study was to obtain lavage effluents from 8 control subjects, 8 healthy power plant workers exposed to fly ash, 1 healthy coal miner, and 1 rock driller with acute silicosis. These effluents were analyzed for total numbers of alveolar macrophages, lymphocytes and neutrophils and for secretory activity of alveolar macrophages. Data were then analyzed to determine what response patterns were characteristic for given dust exposures.METHODSSelection of SubjectsThe 8 control subjectS were all adult males from the area of Morgantown, WV. Two subjects among the controls had smoked cigarettes for approximately three pack-years and had stopped more than ten years ago. The 8 power plant :workers were all healthy adult male employees of a power facility in Hatfield, PA, approximately thirty miles from Morgantown. One of the power plant personnel was a comparable ex-smoker. The remaining subjects were all lifelong non-smokers. The coal miner was a healthy non-smoking male from Morgantown, WV. The rock driller was a patient under treatment with corticosteroids for acute silicosis. He had shown considerable clinical improvement with this treatment but still manifested significant radiologic and pulmonary functional abnonnalities at the time of lavage. The mean age of the 8 control subjects was 36 years (range: 31 to 49 years); the mean age of the remaining subjects studied was 38 years (range: 29 to 53 years)."

Jan 1, 1990

By Launa G. Mallett, Charles Vaught, Kathleen M. Kowalski, Charles D. Litton, Michael J. Brnich, Ronald S. Conti, Henry P. Cole, William J. Wiehagen

How do people behave when they are trying to get out of a fire? Are escape activities different in each incident, or will most actions be predictable across events? Do persons make the same sorts of decisions whether they are responding as individuals or as group members? Because the social costs of fire-related deaths and injuries are likely to continue to rise, societal pressure for greater safety will also undoubtedly increase. There are, therefore, compelling reasons to further our understanding of action in fires. If human behavior in fire is studied scientifically and predicted according to some well-defined principles, the benefits will be significant. Design engineers could incorporate real-world findings into their plans. Equipment manufacturers could gain from insights into how their technology is actually used in fire emergencies. Safety personnel would have a better appreciation of what constitutes adequate evacuation procedures. Trainers could upgrade the content of their courses that teach escape skills. The result would be an overall improvement in the quality of fire preparedness and safety.

Jan 1, 2000

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 4 Hoist Assemblies (not man-rated) A large number of manufacturers supply materials handling winches. These units are predominately electric powered while a limited number of vendors supply air powered equipment. Air powered units are currently used extensively for underground materials handling purposes. Suppliers of materials handling equipment normally include a disclaimer statement in their published literature which clearly states that the equipment "is not designed or suitable for lifting or lowering persons " This category of commercially available equipment can be adequate for emergency man hoisting provided that its' capacity is suitably derated and provided also that the necessary safety features are incorporated. Section C. 5 details the equipment which could be added to a commercial materials hoist to meet these needs. Four commercially available hoist assemblies, two electric and two pneumatic are discussed in the following paragraphs. This equipment is typical of what is commercially available and three of the units are currently used extensively in mining applications. Each hoist description includes a remarks paragraph which identifies the additional equipment each hoist would require for emergency hoist use.

Jan 1, 1976

From the National institute for Occupational Safety and Health Disasters take many forms and demand quick response from emergency workers. They may include natural disasters such as earthquakes or hurricanes, or they may involve manmade disasters such as technological failures or terrorist attacks. As a member of an emergency response team, you and your team members are at risk of experiencing what psychologists refer to as a traumatic incident—an incident that may Involve exposure to catastrophic events, severely injured children or adults, dead bodies or body parts, or the loss of colleagues, for instance. Traumatic incidents can produce unusually strong emotional reactions that may interfere with your ability to function at the scene or later: You may experience any of the physical, cognitive, emotional, or behavioral symptoms listed below in Table 1. Some people experience emotional aftershocks weeks or months after they have passed through a traumatic event. Others may experience these reactions while still at the scene, where they must stay clearly focused on constantly changing hazards to maintain their own safety and to rescue injured victims.

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By Joseph M. Kuchta

This Bureau of Mines manual is oriented to the technical needs of an investigation of fire or explosion accidents and includes various practical and theoretical information that is needed in analyzing accidents or evaluating conditions that might lead to an accident. It is applicable to accidents in the chemical, mining, transportation, and other fuel-related industries. Specific procedures for conducting an accident investigation are outlined, and various guidelines are given for developing the fire or explosion evidence. Ignitability, flammability, and physicochemical data are presented for over 500 combustible gases, liquids, and solids; empirical and theoretical expressions are also given for extrapolating the behavior of combustible-oxidant-diluent systems to various environmental conditions. In addition, various data pertinent to damage analysis are summarized to facilitate the task of the investigator in developing plausible accident scenarios.

Jan 1, 1985

By Edmund S. Leaver, A. P. Towne, Jesse A. Woolf

Part of the work of the Precious Metals Section is to conduct oretesting experiments on ores selected as representative of various mining districts or areas . The projects are authorized by the Metallurgical Division , and only those ores in which gold and silver or gold or silver constitute an essential part of the total values are assigned to the Precious Metals Section . Such ores include those containing the precious metals only as commercially important ingredients , as well as those containing base metals such as copper , lead , and zinc along with the gold and silver . In many instances the "ore " may be a tailing product of a grade good enough to warrant retreatment , or a concentrate for which it is desirable to develop a method of treatment to avoid the expense of shipment to a smelter . It is evident that in general the greater part of this ore - testing work is done according to standard testing procedure , such as cyanidation, amalgamation, gravity - concentration , and flotation , or a combination of these methods . The standard methods of conducting such tests have been outlined in previous reports of ore - testing studies . However , since the inauguration of this oretesting program 6 years ago , the ores submitted under authorization have become increasingly more refractory to simple methods of treatment. Consequently, a considerable number of the projects completed during the fiscal year 1941 have required an unusual amount of work and in some instances have developed into real research problems . For such ores more complete microscopic and spectroscopic examinations and more complete chemical analyses

Feb 1, 1942

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948