Search Documents

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company&apos;s Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

By Edmund Newton

This paper is one of a series comprising the Mineral Industries Survey of the United States, which was begun in 1935. It describes the simple methods of mining and beneficiating manganese ore, in eastern Tennessee and compares these methods with those used elsewhere in the Appalachian region. The report contains general information on manganese to give a clearer understanding of the methods and costs of mining and. beneficiating manganese ore foam a widespread deposit, an in addition presents zone difficulties normally fond in these operations. The marketing, uses, and value of manganese ore are discussed as well as the amount of capital necessary for effective operation on given scale of production, and requirements are outlines for successful operation of manganese, property in this region.

Jan 1, 1941

By Martin J. Gavin

During the present study of lubricating oils in the San Francisco laboratory of the Bureau of mines it became desirable to distill oils used in the experimental work at pressures as low as 10 mm., (mercury column) absolute. In the effort to overcome difficulties and eliminate sources of error the apparatus described below was finally developed. The distilling flask is essentially the Hempel flask used by the Bureau of Mines for the analytical distillation of petroleum3. The complete apparatus is shown in Figure 1. As air leakage at connections is an ever present or potential source of difficulty and error in vacuum apparatus, the, mouth of the flask is drawn down to one cm. internal diameter which materially simplifies obtaining an air-tight seal at this point. Before reducing the mouth, the spray screen is inserted and adjusted in position.

Jan 1, 1927

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By Paul M. Tyler

The outstanding trend in the graphite market is the fast-growing demand for cheaper qualities of graphite and the declining consumption of the more expensive varieties. The manufacture of graphite, crucibles for melting metals was one of the earliest applications of the-mineral and for many years constituted by far the leading source of demand. In later, years, however; and more especially since the Great War, the increasing demand for high-grade steel ingots and castings instead of enlarging crucible sales has permanently curtailed the domestic demand for crucibles because it has hastened the introduction of electric, oil or gas fired furnaces to replace the older types requiring pots to hold the metal during melting. While there has been a substantial increase in the use of graphite for miscellaneous refractories the total consumption for such purposes is too small to offset the shrinkage in demand for crucible making, and though it consumes the better and hence more expensive grades of crystalline flake graphite, it does not call so insistently for the still costlier Ceylon grades.

Jan 1, 1929