Search Documents

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves, To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By David P. Conover

The U.S. Bureau of Mines (USBM) has developed a computer-assisted Ground Control Management System (GCMS) for near realtime evaluation of underground coal mine ground conditions. The GCMS combines existing mine-monitoring system and sensor technology with automated computer analysis techniques to enhance the acquisition, analysis, and display of geostructural data. The GCMS, which combines mine structure data with other information, such as geologic conditions and mine layout, has provided information on mining-induced stress transfer and pressure buildup associated with several ground control events. The GCMS collects and analyzes shield-leg pressure, ground pressure, and strata movement data to evaluate the structural behavior of an active Western U.S. Iongwall coal mine. Field data are transmitted over a dedicated phone line to the USBM Denver Research Center (DRC) mine monitoring laboratory, 240 km (150 miles) from the mine site. Real-time collection, processing, and analysis of mine structure and shield pressure information has proved to be an effective method for near-face ground conditions while mining progresses. The GCMS provides the mine operator with information to rapidly identify and manage potentially hazardous ground conditions while mining is in progress.

Jan 1, 1994

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By Frank E. Cash

Large quantities of explosives are consumed in the underground mining of ores in the Lake Superior district. Because of the recognized danger of accidentally releasing the potential highly destructive forces contained, the safes possible procedure in the transportation, storage, and use of explosives is necessary. Underground magazines recently constructed in the district give evidence of the earnest desire of the mine operators to incorporate all possible safe-guards in the storage of explosives, including a careful choice of location and arrangement in the plan of the magazine.

Jan 1, 1946

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By B. H. Clemmons, C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent on improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silverbearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Mar 1, 1965

By G. L. Neumann

"INTRODUCTION Mining in this area is inactive. The entire region is now comprised of small farms. Because approximately 1,500,000 tons of magnetite ore had been shipped from this area between 1855 and 1915, it was deemed probable that geophysical surveying and core drilling might indicate other ore bodies or sizable extensions of the previously mined ore bodies.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has, as its primary objective, the most effective utilization of our mineral resources, thus fortifying our national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiatien tests.The chemical analyses and beneficiation tests included in this report were performed at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, head of the laboratory service unit.The Mineral exploration Was under the general supervision successively of G. D. Jermain, district engineer, C. B. White, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch.The geophysical section of the exploration was performed by G. B. Botsford, engineer of the Bureau of Mines. Assistance was given by the Division of Geophysical Exploration of the Bureau of Mines, Dr. F. W. Leo, chief."

Dec 1, 1947

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By W. H. Tomlinson

This publication presents the basic text for a 20-hour accident-prevention training course developed for supervisors by the Federal Bureau of Mines. During the past 2 years, the course has been used by the Bureau in teaching more than 300 groups of coal-mine supervisors-men whose responsibility is twofold: To manage in production and maintenance phases of coal mining and to guide their men along paths of safety. This is a handbook for teaching teachers. In this handbook will be found references to safety practices followed by companies that consistently have low accident records. These companies credit their outstanding performance to the adoption and faithful observance of accident prevention by supervisors and workers alike on a wholesome, cooperative basis. Teaching safety to workers involves both on-the-job and classroom-type instruction. If such training is to be permanently effective, it must be reinforced consistently on the job by the immediate supervisor of the worker. This publication is intended to provide such a supervisor with the motivation to provide such follow-up and shows how he can accomplish it effectively.

Jan 1, 1962

By John P. McDonnell

Coal mine bounces and bursts are major problems facing U.S. mine operators. Bounces and bursts have the potential to inflict severe injury on mining personnel, damage equipment, and cause mine closures. High- stress conditions, at or near the working face, are the common denominator in the burst problem, If mine operators can locate high-stress and potentially burst-prone zones, they can then use stress-relief methods to control the burst condition. One method of locating the high-stress zone is the probe-hole-drilling or drilling-yield method. Probe-hole drilling is used frequently in Europe, the U.S.S.R., and Japan as a means for locating potential burst zones. Consequently, the Bureau of Nines performed tests in the laboratory and in a deep, burst-prone western mine to analyze probe-hole drilling. The in-mine method, very simply, involves drilling a hole into the coal seam and measuring the volume of cuttings obtained. A certain volume of cuttings can be expected from a certain diameter and length drill hole. A significant increase in the volume of cuttings means the zone around that particular hole is highly stressed. In-mine use of the drilling yield method has shown it to be a useful tool for locating highly stressed and potential burst zones. Results from laboratory testing confirm that high stress applied tri-axially to a cube specimen will cause a significant increase in the volume of cuttings from a small-diameter drill hole in the specimen.

Jan 1, 1988

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electro-kinetic dewatering and consolidation of metal-mine mill tailings from five mines in the Coeur d'Alene, Idaho, district. Classified (coarse) tailings, slimes, and unclassified material were separately tested. Tailings were placed in 0.3 ft3 plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Moisture content and density of the dewatered material at test end indicated the method to be generally effective for all materials examined, but best results were achieved with well-mixed unclassified tailings.

Jan 1, 1974

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By Thomas Mucho, Anthony Iannacchione

This marks the 100th year that the aggregate industry has been served by a national association. Of all the accomplishments this longstanding relationship has achieved, there is probably none greater than the progress made, in worker safety. Perhaps the best way to measure this success is to examine injury trends in the aggregate miner population. For example, in the first half of the 20th [ ] century, 16 quarry mining disasters (a "disaster" is an incident with five or more fatalities) claimed 157 miners between 1909 and 1952. The largest of these was the disaster at the Sandts Eddy Limestone Quarry near Allentown, Pa., on March 26, 1942, where 31 miners died of asphyxiation by fumes/explosion. Thankfully, no mining disasters have occurred in the aggregate industry since 1952. It is these kinds of information that help us characterize improvements in aggregate worker safety over the last 100 years.

Jan 1, 2003

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 8,445 acres of the 20,650-acre Tunnison Mountain Wilderness Study Area in order to evaluate its identified mi nerd 1 resources. The study area is located in Lassen County, CA, about 8 miles northeast from Susanville. No mineral resources were identified in the study area based on literature, field observations, and sample results. No mines were operating in or near the study area in 1985, and no mines, prospects, or claims have been located in or within 1 mi le of the study area. The study area is underlain by Pliocene and Pleistocene volcanic units composed of basalt, andesite, rhyolite, and some pyroclastics. No metallic and only nonmetallic commodities are present in the study area. These included stone and sand and gravel. Although substantial volumes of basalt and andesite (stone) occur within the study area, no identified resources of these commodities were delineated. Sand and gravel is not economic because of small occurrence size and lack of local markets.

Jan 1, 1987

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008