Search Documents

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By Earl F. Hastings

The Pilgrim mine, operated by the Pioneer Gold Mining Co., is 9-1/2 miles west of Chloride in the Pilgrim mining district on the eastern slope of the Black Mountains, or River Range, Mohave County, Ariz. In March 1937, 100 tons of gold ore per day were being mined and milled at the property by a total force of 5i men. Climatic conditions allow year-round operations. Due to present activity in the county there is an ample supply of labor for the requirements of the mine. The Pilgrim is the only producing property within s radius of 6 miles; recently, however, the South Pilgrim Mining Co. has launched a development campaign on claims that adjoin the Pioneer Co. property to the south.

Jan 1, 1937

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By Melvin P. Silverman

The literature on methane-oxidizing bacteria is reviewed in regard to (1) the growth and isolation of cultures by special techniques; (2) the distribution of these organisms in nature and descriptions of individual species; (3) the physiology of methane-oxidizing bacteria as influenced by temperature, light, pH, aerobiosis versus anaerobiosis, and carbon and nitrogen sources; and (4) the biochemistry of methane oxidation revealed by studies with intact cells and subcellular systems. Present practical applications of methane-oxidizing bacteria are limited to prospecting for natural gas and petroleum deposits. Desirable areas for future research are discussed as well as some possible applications such as (1) the removal and/or early detection of methane gas in coal mines by intact culls or enzyme preparations; (2) the generation of electrical energy by microbial fuel cells using methane as fuel; (3) the growth of methane-oxidizing bacteria on methane fur their food value; (4) the purification of hydrocarbon gas mixtures using methane-oxidizing or other alkane-oxidizing bacteria; and (5) the synthesis of methane from mixtures of H2 and CO or H2 and CO2 by methane-forming bacteria.

Jan 1, 1964

By A. G. Sharkey

THE PURPOSE of this investigation was to develop methods for analyzing coal derivatives and products from the Fischer-Tropsch synthesis. As part of this investigation it was necessary to study the mass spectral characteristics of many classes of compounds. The mass spectra of alcohols, the trimethylsilyl ether derivatives of alcohols, acetal-type compounds, ketones, esters, and naphthenes were correlated with structure, and analytical methods were formulated. A method was devised to determine the ratio of branched to normal hydrocarbons up to CIS in the Fischer-Tropsch product. Low-ionizing-voltage mass spectrometry was combined with type-analyses to analyze tar acids and neutral oils from coal. The necessary sensitivity correlations at low-ionizing voltage were developed, particularly for phenolic compounds. Special analytical techniques were developed for the mass spectral analyses of specific compounds and compound types including (1) oxides of nitrogen, (2) hydrogen sulfide, (3) isomers of butenes and pentenes, and (4) hydrogen deuteride. An investigation was made of the effects of various hydrocarbons and oxygenated compounds on tungsten filaments in the mass spectrometer. The operating characteristics of rhenium filaments under similar conditions were studied. Several improved sample handling techniques were developed, including an automatic manometer and a self-filling micropipet. Studies were made of anomalous and negative peaks in the mass spectra of certain gases.

Jan 1, 1967

By Tignor E. M.

The Brenneman oil field in Grant District, Hancock County, W. VA., was selected for study by Bureau of Mines engineers because it was typical of many of the smaller petroleum reservoirs in the Appalachian region. In 1906, E. W. Marland & Co. discovered the Brenneman field by drilling a well that readied the oil-bearing .Berea sandstone at a depth of 750 feet and initially produced 200 barrels of oil a day. Most of the oil-productive area (348 acres) of the field was developed in a comparatively short time, and the initial daily production rates of some of the wells were as high as 1,000 barrels of oil a day. Although the field was a prolific producer of oil for several years, it was abandoned in 1923 when the production rate was less than 1,000 barrels of oil a year and 705,000 barrels of oil had been produced. Secondary-recovery operations were started in the Brenneman field in 1927 after useable old wells had been repaired and unsatisfactory wells had been plugged; drilling of new wells was started in 1929. The peak of the redevelopment program was reached in 1942 when 92 oil-producing wells and 26 injection wells were in use; both air And mixtures of air and natural gas were used for injection purposes. It is estimated that approximately 357,000 barrels of oil, equivalent to 1,030 barrels per acre, 105 barrels per acre-foot, 8.5 percent of the total pore volume, or 11.9 percent of the original oil in place will be produced as a result of gas-injection secondary-recovery operations. Engineers of the Bureau of Mines Petroleum Field Office, Franklin, Pa., are studying secondary-recovery projects in the Appalachian region as a part, of the Bureau's secondary recovery research and are reporting these studies so that others: can profit by the experience gained from the operations. In common with most of the other Appalachian oil fields, there was no natural water drive in the Brenneman field. The estimated oil saturation in the Brenneman reservoir at the end of economic gas-injection operation indicates that additional oil might be recovered economically by water flooding and that a pilot flood would be warranted.

Jan 1, 1950

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

By E. L. Litchfield

Spark ignition of combustible-gas mixtures is a relatively old subject of investigation and has been treated both experimentally and analytically by many people. Elements of static and current electricity are almost always present in mining and industrial operations, and the spark can be an extremely efficient source of ignition. Thus the practical interest of such problems as the "intrinsic safety" of electrical apparatus is obvious. Ignition and quenching phenomena are the primary laboratory representatives of combustion phenomena that are dynamically nonsteady, and such nonsteady phenomena playa considerable part both in industrial processes and in safety matters, although they are of less immediate practical interest. Considerable effort has been expended by the Federal Bureau of Mines in investigations of spark ignition.5 6 7 8/ Primarily, this work has established the significance of several of the parameters involved. Although the

Jan 1, 1959

By Thomas J. Peters

The U.S. Bureau of Mines conducted a mineral investigation, and the U.S. Geological Survey did a geological appraisal of an east portion of the Bear-Marshall-Scapegoat-Swan (BMSS) RARE II area (No. A1485) to provide mineral resource information for land use planning. The Bureau of Mines' investigation consisted of a library and field search for all mineral properties and occurrences, and included a review of Teton County mining claim records. Those records showed two placer claims, the only mining-related activity known in the area. Six reconnaissance pan samples were taken in the vicinity of the two placer claims, the Lone Star and Spotted Horse, located on Hannan Gulch in 1900 and 1901. One sample contained a trace of gold, but there are no identified resources. However, the study area is in the Rocky Mountain Overthrust Belt, which is productive for oil and gas elsewhere. The entire study area is blanketed by oil and gas leases and is currently being explored.

Jan 1, 1983

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By Robert C. Hickman

In its search for strategic minerals, the Bureau of Mines investigated the Rutherford Mine property in Amelia County, Va. The property was visited by F. W. Horton, mining engineer, and Margaret Fuller Boos, mineral technologist, of the Bureau of Mines, in company with Eugene Dawson, of the War Production Board, on July 16-11, 1943. An exploration program by the Bureau was recommended, and work was started on July 28, 1943, and continued until September 16, 1943. A total of 1,250 feet was diamond drilled in 5 holes on the property.

Jan 1, 1950

By Frank E. Cash

Data on the occident experience of the pebble-phosphate industry in Florida for 1937 and 1938 are combined in this report with statistics for the 7-year period 1930-36, inclusive, which were published in Information Circulars 69174/ and 69685/. The periodic publication of such data enables the pebble-phosphate industry, as well as other industries, to consider relative hazards, compare experience, and thereby help to prevent accidents. ACKNOWLEDGMENTS Accident data ere furnished by the following; operating companies: Amalgamated Phosphate Co., Brewster; American Agricultural Chemical Co., Pierce; Coronet Phosphate Co., Plant City; International Agricultural Corporation, Mulberry; Phosphate Mining Co., Nichols; Southern Phosphate Corporation, Bartow; and Swift & Co. Fertilizer Works, Bartow.

Jan 1, 1940

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983