Search Documents

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed-limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and sup-plies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By L. A. VANFLEET, Allen D. Look

The ever -present danger of mine fires and the possibility of hazardous atmospheric conditions in underground mines make a well-equipped mine rescue station a valuable asset to any mining district . Rescue equipment without proper maintenance provides only false security , because neglect may make the apparatus unfit for use in an emergency . Promptness in fighting mine fires is important ; frequently the first 30 minutes of action are worth many hours later . Likewise , the equipment will be of little value if enough men trained in its use are not readily available . This circular points out how such protection has been provided in an Arizona mining district by establishing a well- organized , adequately equipped , central mine rescue station. ·

Aug 1, 1950

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By D. Harringtong

"There has been much writing and argument on the subject of giving bonuses to miners, quarrymen, metallurgical and chemical workers, and others as a stimulus for safe work and for work safely done. Theoretically, everyone should be careful and should not need monetary or any other type of encouragement for the prevention of accidents; as a. fact, few people are careful, and this is primarily the reason way many if not most accidents occur. A bonus, however, is not simply money given away by an employer; it must be earned, so to speak, before it becomes due; in other words, if the standard established is not reached, no bonus is paid, and in many cases some disciplinary action is taken.The United States Bureau of Mines Is asked from time to time for suggestions for rewards to mine workers who have a good attitude toward working safely or who need some stimulus to cause them to make greater or more earnest efforts toward safety for themselves and their co-workers. A recent inquiry prompted the collection of data on some safety bonus systems from reports of this bureau's field engineers and others, and some of these Now given. Bonus practice at both coal and metal mines is included because a system used at metal mines is generally adaptable to coal mines; in fact, in numerous cases, bonus systems recently started at some coal mines are based on systems in vogue and giving satisfaction some metal mines; in-some instances, also, metal mines have been able to get good suggestions from coal mines or from the cement or petroleum industries. it .should be understood that a bonus, even as applied to the encouragement of safety, does not necessarily mean payment of money; in fact, some successful bonus systems have in them no direct money exchange; hence, the bonus as treated in this paper is that defined as ""Something given in addition to what is ordinarily received by, or strictly due to, the recipient.""Acknowledgment is given here to members of the safety division of the Bureau of Mines who sent in some of the information here presented; to the Engineering and Mining Journal and Mining Congress Journal, from which some items were abstracted; to various mining officials who gave data in one form or another; and to M. von Bernewitz, of the United. States Bureau of lines who aided in framing parts of this paper."

Jun 1, 1932

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By Ivette E. Torres

Many significant events that began in 1990-91 continued to have a profound impact in the world minerals economy in 1992. The dissolution of the U.S.S.R. and the formal breakup of the Council for Mutual Economic Assistance (CMEA) had significant effects far beyond the geographic boundaries of Europe and Central Eurasia. CMEA's network of economic interdependence had relied on central planning, a variety of subsidies, and barter agreements that allowed its members to function without the pressures of productivity and efficiency. In the mineral sector, many decisions had been made based on the need for military planning and technology competition with the market economy world. Because of inexpensive oil available through subsidies and technology assistance from the former U.S.S.R., industries III CMEA member countries had been able to function and maintain production to supply minerals and materials required to support the policies of the central plan. In 1992, most of the former CMEA countries decreased their output of many minerals. In some cases, the network of production that had been in place was severed. Political and economic instability, destruction of infrastructure, and new priorities were affecting other mineral industries in the area. In late 1991, 15 independent countries replaced the U.S.S.R. and in early 1991 the former CMEA countries found themselves trying to adjust to the realities of economic independence and the need to compete with former allies for survival. Although 11 of the 15 former Soviet republics joined in the Commonwealth of Independent States (CIS) in December 1991, in 1992, individual economic needs exceeded the needs of the Commonwealth III importance. As a result, new mineral trade patterns emerged as minerals were used as a source of much needed capital.

Jan 1, 1994

By Michael D. Fenton

Social and political movements that had been gathering momentum over several years continued in 1993 to dramatically affect and inspire uncertainty on the global mineral industry. Privatization of government-controlled mineral industries continued throughout the world, especially in Africa, Asia, Central Eurasia, Eastern Europe, Latin America, and Western Europe. The reasons for privatization varied among regions and countries, but the trend was universal and was not expected to end soon. Regional trade blocks were being developed and expanded. The European Union (EU), the North American Free Trade Area (NAFTA), the Association of Southeast Asian Nations (ASEAN) , the Asia Pacific Economic Cooperation (APEC) , and the Latin American Southern Cone Common Market (MERCOSUR) were expected to contribute to reduced internal tariffs and increased minerals trade. Minerals consumption within the politically unstable former Soviet Union (FSU) decreased significantly without a simultaneous cutback in production, while its exports flooded the world's mineral markets. These exports into Western Europe and Japan, still in economic recession, depressed minerals and metals prices worldwide, especially for aluminum, magnesium, nickel, and potash. Increasingly restrictive environmental laws and land-access limitations in Australia, Canada, Western Europe, and the United States tended to discourage mineral resource development. However, the number of undeveloped countries in Latin America and Asia that encouraged exploration and development by revising mining and tax laws and regulations increased, thereby increasing investment opportunities for foreigners.

Jan 1, 1995

By R. Barany

Thermodynamic calculations pertaining to the minerals gibbsite, kaolinite, halloysite, and dickite have been hampered by the lack of adequate heat and free energy of formation data. Previous data for gibbsite were highly uncertain, and there were no data for the other three substances. By use of hydrofluoric acid solution calorimetry, the Bureau of Mines derived heat of formation values from the elements and from the oxides for the four substances, and the data were combined with known entropy values to obtain the corresponding free energies of formation. The results show that gibbsite and halloysite are thermodynamically unstable with respect to the oxides (a- alumina, a- quartz, and liquid water) at 298.15° K,, while kaolinite and dickite are only moderately stable (to about the same degree), The instability of halloysite, in comparison with kaolinite and dickite, results in a 60°-lower equilibrium decomposition temperature.

Jan 1, 1961

By Ramie H. Thompson

1.1 BACKGROUND In many underground coal mining operations the use of electromagnetic field equipment, particularly communication systems, not only increases the overall efficiency of the mining operation but can be directly linked with mine safety considerations. The use of electromagnetic field producing equipment in underground coal mining operations can only be expected to grow. Several new communication systems have already been proposed. In addition, high-frequency producing equipments for many diverse uses in mining operations are under study. The use of these equipment in underground mining operations is hampered by the possibility of their electromagnetic fields interacting with the electric blasting cap operations commonly carried out in the mines. Such interactions can have at least two results bearing directly on mine safety: o premature initiation of the cap, either in its normal shot location or during hookup or transportation; o dudding of the cap so that normal firing operations do not cause irritation; thereby leaving unexploded high explosives after normal firing. Since the consequences of a premature initiation could, particularly in coal mines operations, result in catastrophe involving human life, the overall approach to prediction of possible hazard must be, as far as possible, of a "worst case" nature. The general problem of predicting possible RF hazards for any electroexplosive device (EED) is best treated by reference to Appendix A of

Jan 9, 1983

By McHenry Mosier

The application of diamond drills for blast holes is limited to the special Job of extracting floor and stope pillars, and therefore their operation is intermittent. The zinc ore drilled occurs in metamorphosed dolomitic limestone. The mining method is sublevel open-stoping on 200- foot lifts. Ample fresh air is provided by mechanical ventilation. Diamond drilling blast holes began in August 1944. Drills were mount- ed on a 3-inch quarry bar. The contract price for labor for operating equipment owned by the company was $0.23 per foot. The diamond bits were cast-set at the factory in a sintered tungsten matrix. Bit replacement costs were $0.15 to $0.20 per foot drilled. The feet drilled per bit ranged from 87 to 258. The feet drilled per diamond-drill shift ranged from 121 to 129. Holes were loaded with 60-percent special gelatin dyna- mite and fired electrically. In percussion drilling, the estimated feet drilled por machine shift with hand-held sinkers was 65. The tons broken per machine shift averaged 40 throughout the mine. Detachable bits have been adopted recently. The principal advantage of diamond-drilling blast holes at the Balmat mino is the extraction in a safe manner of ore not minable by short-hole drilling. The principal disadvantago is the greater cost per foot of holo in comparison with percussion drilling.

Jun 1, 1947

By D. J. MacDonald

As part of a U.S. Bureau of Mines program seeking improvements to the Bayer process, a typical Jamaican bauxite was heated at temperatures up to 500° C in hydrogen, and its leachability under Bayer process conditions was measured and properties of its leached residue were observed. The objectives were to find ways to decrease the amount of organic carbon in bauxite or in leach liquor derived from it without impairing its leachability, and to improve the leached residue's filterability. Techniques employed included heating bauxite under pressure in an autoclave with hydrogen, and in flowing hydrogen at ambient pressure in a tube furnace. Leaching tests were done with a 600-mL stirred reactor. In some of the leaching tests, ferrous sulfate (FeS04) was introduced before leaching to produce a partially magnetic product. Results showed that exposure to hydrogen at temperatures from 160° to 360° C progressively diminished the bauxite's content of organic carbon and decreased the ratio of organic carbon to aluminum in leach liquor, an improvement that would allow a process using hydrogen-treated bauxite to be operated at a smaller recycle ratio, thereby consuming less energy and allowing greater throughput for a plant of given capacity. The bauxite's leachability was not impaired by high-temperature pretreatments, except at temperatures higher than 280° C. Pretreatments in hydrogen produced black, partially reduced bauxite which upon leaching gave a residue that was attracted to a magnetic field and was amenable to separation from green liquor by a magnetic filtration method.

Jan 1, 2010

By K. Biswas, S. Iverson, S. J. Jung

Computer modeling of rock flow in ore passes is being investigated and compared using MSC Soft-ware’s Working Model 2D1 (WM2D) and Itasca Corp.’s Particle Flow Code in Two Dimensions (PFC2D). This work is being carried out by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health to determine the usefulness of computer modeling to improve ore pass design. The types of tests included pendulum tests to validate WM2D simulations and simulated single-rock drop tests in both WM2D and PFC2D to understand their contact models. Simulated rock impacts at the ore pass chute and the use of inclined ore passes and doglegs were investigated in both programs. A PFC2D simulation showed that dynamic loads at the chute gate were reduced significantly when a dogleg transition was used, and simulations in which the ore pass was inclined showed significant reductions in chute impact loads compared to simulations of a vertical ore pass. A released hang-up was simulated using PFC2D.

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982