Search Documents

By Michael D. Fenton

Social and political movements that had been gathering momentum over several years continued in 1993 to dramatically affect and inspire uncertainty on the global mineral industry. Privatization of government-controlled mineral industries continued throughout the world, especially in Africa, Asia, Central Eurasia, Eastern Europe, Latin America, and Western Europe. The reasons for privatization varied among regions and countries, but the trend was universal and was not expected to end soon. Regional trade blocks were being developed and expanded. The European Union (EU), the North American Free Trade Area (NAFTA), the Association of Southeast Asian Nations (ASEAN) , the Asia Pacific Economic Cooperation (APEC) , and the Latin American Southern Cone Common Market (MERCOSUR) were expected to contribute to reduced internal tariffs and increased minerals trade. Minerals consumption within the politically unstable former Soviet Union (FSU) decreased significantly without a simultaneous cutback in production, while its exports flooded the world's mineral markets. These exports into Western Europe and Japan, still in economic recession, depressed minerals and metals prices worldwide, especially for aluminum, magnesium, nickel, and potash. Increasingly restrictive environmental laws and land-access limitations in Australia, Canada, Western Europe, and the United States tended to discourage mineral resource development. However, the number of undeveloped countries in Latin America and Asia that encouraged exploration and development by revising mining and tax laws and regulations increased, thereby increasing investment opportunities for foreigners.

Jan 1, 1995

By R. Barany

Thermodynamic calculations pertaining to the minerals gibbsite, kaolinite, halloysite, and dickite have been hampered by the lack of adequate heat and free energy of formation data. Previous data for gibbsite were highly uncertain, and there were no data for the other three substances. By use of hydrofluoric acid solution calorimetry, the Bureau of Mines derived heat of formation values from the elements and from the oxides for the four substances, and the data were combined with known entropy values to obtain the corresponding free energies of formation. The results show that gibbsite and halloysite are thermodynamically unstable with respect to the oxides (a- alumina, a- quartz, and liquid water) at 298.15° K,, while kaolinite and dickite are only moderately stable (to about the same degree), The instability of halloysite, in comparison with kaolinite and dickite, results in a 60°-lower equilibrium decomposition temperature.

Jan 1, 1961

By McHenry Mosier

The application of diamond drills for blast holes is limited to the special Job of extracting floor and stope pillars, and therefore their operation is intermittent. The zinc ore drilled occurs in metamorphosed dolomitic limestone. The mining method is sublevel open-stoping on 200- foot lifts. Ample fresh air is provided by mechanical ventilation. Diamond drilling blast holes began in August 1944. Drills were mount- ed on a 3-inch quarry bar. The contract price for labor for operating equipment owned by the company was $0.23 per foot. The diamond bits were cast-set at the factory in a sintered tungsten matrix. Bit replacement costs were $0.15 to $0.20 per foot drilled. The feet drilled per bit ranged from 87 to 258. The feet drilled per diamond-drill shift ranged from 121 to 129. Holes were loaded with 60-percent special gelatin dyna- mite and fired electrically. In percussion drilling, the estimated feet drilled por machine shift with hand-held sinkers was 65. The tons broken per machine shift averaged 40 throughout the mine. Detachable bits have been adopted recently. The principal advantage of diamond-drilling blast holes at the Balmat mino is the extraction in a safe manner of ore not minable by short-hole drilling. The principal disadvantago is the greater cost per foot of holo in comparison with percussion drilling.

Jun 1, 1947

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By M. Terry Hoch, George J. Karabin, James M. Kramer

This paper introduces the fracture mechanics approach—a unique way to predict the stability of a coal mine panel. The technique uses analytic equations to calculate the stress, strain, and yield characteristics of coal support systems. It uses fracture mechanics to model almost every type of mine support structure. Another feature is a method that incorporates field-tested knowledge into the analytical analysis. For example, this technique can model the yield characteristics of a coal seam by combining empirical pillar strength equations into the analytic analysis. It may be possible to simulate multiple-seam mining by incorporating subsidence methods into the analysis. The method is simple and quick, which makes it attractive for stress analysis software. It should be more accessible to those in the mining industry who do not have expertise in rock mechanics or numerical modeling. Although the purpose of this research is for modeling coal mines, it should be adaptable to any mine in a tabular deposit.

Jan 1, 1999

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By David F. Smith

[The U. S. Bureau of Mines at its Pittsburgh Experiment Station is frequently called upon to determine by laboratory tests the explosibility of suspensions in air of various dusts encountered in mines and elsewhere. Not all dusts which are combustible or contain combustible material will form explosive mixtures with air under ordinary conditions of temperature and pressure. They may not be highly combustible enough. They may contain a considerable amount of inert or non-combustible material or, the dust particles may not, be fine enough to form explosive mixtures. A knowledge off the chemical composition of a dust together with a determination of the size of the particles often gives valuable indications. But in many cases actual explosibility tests are necessary. Such a case is evidently that of powdered soap, whose explosibility hazard the Bureau was recently called upon to determine, Although an explosion which occurred in a soap plant as early as 1890 was attributed4 to powdered soap, it is apparent, due to the great number of inquiries received by the Bureau, that the hazard presented by powdered soap has not been at all generally appreciated. To the writers' knowledge, no extensive investigation of the explosibility of powdered soaps has been made. It is only recently that pure powdered soap has been manufactured on a large scale. The familiar "soap powder" in the past was usually a mixture of soap with a relatively large quantity of sodium carbonate. Often it contained large amounts of moisture and abrasive material. Even a highly combustible dust when mixed with large quantities of inert dust will not form explosive mixtures with air. Pure powdered soap, however, presents a different aspect. Pure soap is formed by combination of alkali (incombustible material) with fatty acid (combustible material). Toilet soap fray also contain a certain amount of glycerin and essential oil winch, being combustible influence the explosibility]

Jan 1, 1928

By Robert C. Bates

Variations in water percolation rates through saturated cohesionless hydraulic backfill (mill tailings) have been studied in relation to the many physical aspects of the system to determine the most important factors in causing these variations. A multivariable least-squares regression analysis of 135 separate tests shows that a reliable estimate of the water percolation rate through typical hydraulic backfill can be made if the bulk density (unit weight), specific gravity, and grain-size distribution are known or can be estimated. Equations for predicting percolation rate, coefficient of permeability, and seepage velocity are developed both for the range of data analyzed and for extrapolation. The prediction equations for use within the range of data studied are quite accurate, while the ones developed for extrapolation are less accurate but still give reasonable approximations of flow rates. The equations given are valid for cohesionless materials that are free of clays and micas, exemplified by classified mill tailings. The equation developed for predicting percolation rates is as follows: 1nP20 = 11.39147 + 2.853422 1n(VR X D10) + 0.1747436 VR X Cu -178.8039 D10 X D50 + 311.7034 (DSO )3, (1) where P20 = percolation rate, inches per hour at 20° C; correction factors for other temperatures are given in the text, VR = void ratio, dimensionless, D10 = effective size (diameter in millimeters of the 10-percent-finer grain size), Cu = coefficient of uniformity (ratio of the diameter of the 60-percent-finer grain size over D10), D50 = average size (diameter in millimeters of the 50-percent-finer grain size), and In = natural logarithm (log to the base e). The prediction equation for percolation rate is rather complicated, so for practical use a nomograph that simplifies the solution of the prediction equation was developed.

Jan 1, 1967

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By W. L. Cornell

The Missouri Pb ores are the only domestic Co resource being mined and processed for other metals; therefore, they present a viable short-term opportunity for Co production. Lead, zinc, and copper concentrates are produced from the ore. The Cu concentrate can contain up to 30 pct Co and the Pb concentrate up to 15 pct Co. Since Co is detrimental to the processing of the Zn concentrate; the remainder of the Co is rejected to the tailings. The tailings can contain as much as 50 pet Co originally present in the mined ore. Researchers at the U.S. Bureau of Mines have successfully tested on a continuous basis a process that recovers a bulk sulfide concentrate from mill tailings. The concentrate contains up to one-half of the Co and from 50 to 90 pct of the Pb, Zn, and Cu. Concentrate weight represents 10 pet or less of the total tailings.

Jan 1, 1989

By F. H. Nehl

Ion elutriation was used to extract silver cyanide complexes and free cyanide from aqueous streams containing up to 10 ppm silver and 5 ppm free cyanide. Screening tests selected nine of 350 different surfactants for further, larger scale experiments. The screening procedure used 0.1 g of each of the surfactants in 300 mL of synthetic wastewater. Air was sparged into the test cell at 50 cc/min. The foam was refluxed during the tests and was not sampled. Samples of the solution were taken at specified intervals and analyzed by wet chemical methods for free cyanide and by atomic absorption for silver content. The most effective surfactants lowered the silver and free cyanide concentrations to less than 0.5 ppm in 1 h or less. These surfactants were quaternary amine salts with one long chain (C12-C18) organic group and three methyl groups. Experiments using 3 L batches of wastewater or an ion elutriation cell continuously fed with solution draining from an inactive heap leach operation confirmed the results from the screening tests.

Jan 1, 2010

By Michael J. Sapko, Kenneth L. Cashdollar

In This Chapter [Methane ignition as initiation source for much larger secondary coal dust explosions Rock dusting requirements to prevent coal dust explosions Dangers of hybrid mixtures of methane and coal dust] Although methane explosions are dangerous, those that involve coal dust are even more so. If exploding methane disperses and ignites the coal dust that has accumulated on the mine ribs and floor, the burning coal dust immeasurably increases the strength of the explosion. Such methane-dust explosions are prevented by inerting the coal dust in a way that prevents the exploding methane from igniting it. This chapter discusses the dust hazard and how it is pre-vented in U.S. coal mines. METHANE IGNITION AS INITIATION SOURCE FOR MUCH LARGER SECONDARY COAL DUST EXPLOSIONS The typical scenario for coal mine explosions starts with the ignition of a flammable methane-air atmosphere near the face. The turbulent winds from the primary methane explosion then disperse the coal dust. If there is insufficient rock dust (usually limestone), a secondary coal dust explosion then propagates throughout large sections of the mine. These scenarios have been studied extensively at the Bruceton Experimental Mine (BEM) and the Lake Lynn Experimental Mine (LLEM) of the NIOSH Pittsburgh Research Laboratory. The minimum quantity of methane required to initiate a coal dust explosion was studied in 1930 in the BEM [Rice et al. 1933; Nagy 1981] and then later in the LLEM, whose cross-sectional area (130 ft2) is over twice that of the BEM [Sapko et al. 1987a]. Studies conducted in the BEM closely simulated conditions that existed in operating mines in the early 20th century. The later tests in the 20-ft-wide entries of the LLEM simulated the geometries of modern mines with advanced roof support technology. The data from the BEM tests show that 13 ft3 was the minimum quantity of methane at the face that, when ignited, would disperse and ignite coal dust. In the BEM, this amount of methane was mixed with air to form a total flammable volume of about 140 ft3 of a 9% methane-in-air mix-ture. In the wider entries of the LLEM, about 37 ft3 of methane was required to disperse pure coal dust and start a self-sustained coal dust explosion. This amount of methane was mixed with

Jan 6, 2006

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.