Search Documents

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By O. Q. Leone

Composite diaphragms were used in the investigation of electrowinning Ti from TiC14 in a fused LiCl-KCI-TiC'2 electrolyte. Composite diaphragms tested were of two general classes--those consisting of two or more solid materials, and those which contained, in addition, a loose material. An electrowinning cell using a flat diaphragm is described. The maximum current density for these diaphragms was 300 amp per ft2. Lower currents permitted longer operation times. The composite diaphragms gave electrode efficiencies that averaged approximately 60 percent, and the electrowon titanium was of good quality--some Brinell hardnesses were as low as 68.

Jan 1, 1972

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By R. Andre, R. L. Grayson, T. Simonyi

"Results from research directed at determining the reason(s) for the ""rank factor"" in correlations between coal workers' pneumoconiosis incidence and coal seam of employment are presented. Using compliance dust samples collected from two longwall panels operating in coal seams of widely different rank, respirable particles were identified by mineral species under manual scanning electron microscope (SEM) energy dispersive x-ray (EDX) analysis and then further characterized by their physical diameter, general shape, and periphery angularity. Size fractional, mineralogical variations are presented.Of primary significance, the percentage of mineral particles from the higher rank coal seam that were uncontaminated by non-stoichiometric elements for a specific mineral species was twice that of those in the lower rank seam. The relationship held for each mineral species, including quartz. This fact may form the basis for the ""rank factor"" known to exist as well as provide a reason for the contradictory role of quartz and other minerals in previous CWP studies.An important subsequent research priority is now focusing on determining the percent¬age of all respirable dust particles that are minerals versus single-phase organic or multi-phase organic-inorganic complexes. This effort will be accomplished usingautomated SEM-EDX. The mineral purity factor will be developed further, but additional emphasis will be focused on determining the extent of inorganic inclusions in organic particles."

Jan 1, 1988

By George A. Morgan

There was little change in the mineral industry of Benin in 1986, as the economy remained in the grip of a regional recession exacerbated by failing oil prices, which nullified much of the income from Benin's oil production. Benin's industrial sector accounted for less than 10% of the gross domestic product (GDP), with the mineral industry providing about one-half of that total. Several major projects initiated over the last several years continued to perform and/or progress below Government expectations. These included the Save sugar refinery, the Dassa-Parakou section of the Dassa-Cotonou highway, the Benin-Togo Nangbeto hydroelectric plant, the Onigbolo cement plant, and the Semé Oilfield. Funding for these projects is the major source of the Beninese external debt, which was estimated to be over $800 million.2

Jan 1, 1988

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By P. D. Laverty

The U.S. Bureau of Mines treated mixed and contaminated super alloy scrap by pyrometallurgical and hydrometallurgical methods to separate and recover metal values. Best results were obtained by leaching Zn-treated or atomized scrap with HCI-02 at 9SO C and 50 psig 02' This resulted in dissolving approxi-mately 98 pet of the AI, Co, Cr, Cu, Fe, Mn, Ni, and Zn while rejecting over 98 pct of the Mo, Nb, Ta, Ti, W, and Zr as an insoluble refractory residue. Chlorine was successfully substituted for HCI to leach Zn-treated scrap but was unsuccessful for leaching atomized scrap. The leaching solution was treated by pH adjustment and hydrothermal precipitation at 2000 C for 4 h to remove AI, Cr, Fe, and other contaminants as a filterable precipitate. Recovery of Co and Ni would be accomplished by solvent extraction and e1ectrowinning. Chromium recovery as a ferroalloy was demonstrated.

Jan 1, 1989

By W. F. Wyman, S. F. Ravitz

"INTRODUCTION By far the greater part of the high-grade manganese ore used in the United States is imported from overseas. During the early part of the recent World War importations of manganese ore were seriously threated, and it appeared that it would be necessary to utilize low-grade domestic ores to the fullest possible extent. Among the processes that appeared to offer the best possibilities for beneficating low-grade domestic oxide manganese ores, which ordinarily are net readily amenable concentration by ore-dressing methods, were those involving leaching with sulfur dioxide. The Bureau of Mines therefore investigated the amenability of a large number of such ores to sulfur dioxide leaching.Several sulfur dioxide processes for beneficiating low-grade oxide manganese ores have been proposed. 3/ One of these, based on a patent by Van Arsdale and Maier, 4/ was used recently in a plant constructed to treat 1,000 tons per day of 20-percent manganese ore from the Three Kids deposit near Las Vegas, Nev. 5/ In this process the ore slurry is leached with sulfur dioxide gas, the resulting solution is evaporated to crystallize the manganese sulfate, the crystals are decomposed thermally to produce high-grade manganese oxide and regenerate sulfur dioxide, and the manganese oxide product is nodulized. The Bureau of Mines has recently developed a process 6/ in which a suspension of the ore in calcium dithionate solution is leached with dilute S02 gas, the manganese is recovered from the resulting solution by a simple lime precipitation, and the precipitate is nodulized or sintered to form a high-grade manga¬nese oxide product."

Jun 1, 1947

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976