Search Documents

By James J. Olson

Previous Bureau of Mines studies of vibrations from quarry blasts have shown that the square root of the charge-weight may be used to group particle velocity data from various charge sizes, and that empirical propagation equations may be used to estimate vibration amplitudes. Particle accelerations of the sandstone roof of the White Pine Copper mine, Michigan, were measured to determine whether similar propagation equations may be developed for underground mine blasts. Vibration data from White Pine blasts were best grouped by scaling with the square root of the charge weight. Cube root scaling did not effectively group the data. The empirical propagation equation AW1/2 = 50,000 (R/W1/2)-2.21 where A is peak-to-peak acceleration in g's, W is the zero-delay charge-weight in pounds, and R is the distance from the blast in feet, may be used to estimate maximum vibration amplitudes from production sized blasts. Vibration differences among headings and types of explosive charge (AN-FO and dynamite), while statistically significant, were not a major factor in the estimation of maximum vibration amplitudes with an empirical propagation equation. Vibration differences between types of explosive charge were larger than the differences among headings, indicating that some reduction of vibration amplitude might be gained by using AN-FO rather than dynamite. Acceleration records from both White Pine's AN-FO and dynamite production blasts show that high intensity vibrations from the delayed portions of the blast (each delay interval = 25 milliseconds) were separate events, and that the zero-delay portion of the blast produced the maximum vibration amplitudes. If the pull of the underground blast round can be maintained, a reduction of the zero-delay charge-weight may effectively reduce the maximum vibration amplitude of the blast.

Jan 1, 1970

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By Wilbur I. Duvall

Surface vibrations of ground, rock, and structures resulting from blasting or other sources are often measured with portable seismographs. These instruments are usually supported by a three-point mount or tripod which is simply placed on a horizontal surface on which vibration levels are to be measured. The rigid-body motion of a tripod-supported seismograph is considered from the point of view that there should be no slippage of the feet with respect to the surface and none of the feet should leave the surface as a result of imparted motion. From these studies the following design criteria are deduced which assure that the seismograph will respond accurately to vibration levels as large as 1/2 g.:3/ First, the coefficient of friction between the feet and the surface on which the instrument rests should be as large as possible, preferably approaching unity; second, the center of gravity of the instrument should be vertically above the centroid of the three-point mount; and third, the vertical distance between the center of gravity of the instrument and the centroid of the three points of contact with the surface should be less than the perpendicular distance between the centroid point and anyone of the three sides of the triangle formed by the three points of contact. Portable seismographs that do not satisfy these conditions should be clamped to the surface if vibration levels above 0.1 g. are to be recorded.

Jan 1, 1961

By Alton B. Cook

The practice of using partly depleted oil reservoirs for gas-storage operations is proving successful. Moreover, this practice provides a method of secondary oil recovery when gas is cycled at full-storage reservoir pressure. Because of the relative newness of this operation, a study was undertaken to assist engineers in developing improved gas-injection and production procedures and in calculating the amount of gas needed for completely repressuring reservoirs. This paper is the third in a series reporting the progress of a study by the Federal Bureau of Mines of reservoir performance during complete gas repressuring and gas cycling. A procedure for estimating secondary oil recovery by this method is also under study. One report (7)3/ describes the laboratory equipment. The other report (8) gives (1) data on the New York City field, Clay County, Tex., which has been converted to gas-storage operations; (2) laboratory data from research with a model oil reservoir, in which primary production, complete gas repressuring, and gas cycling for the New York City field were simulated; and (3) theory to explain reservoir performance during gas repressuring.

Jan 1, 1961

By James P. Ulery

A Bureau of Mines geologic study of Pennsylvanian and Permian coalbeds in southwestern Pennsylvania was undertaken to determine the effects of coalbed geology and petrology on in situ coalbed gas contents. Data were obtained from 18 coreholes from parts of four 7.5 ' quadrangles in southwestern Washington and northwestern Greene Counties, and from a single corehole in Westmoreland County. A total of 88 samples from 24 coalbeds were collected for direct-method testing to determine gas content. The samples were also analyzed for petrographic composition, chemical composition, and vitrinite reflectance values. Corehole information was used to generate isopach maps and geologic cross sections useful in data interpretation. Results of the investigation show that coalbed gas content is related to vitrinite reflectance, but not to petrographic composition. Gas contents are also influenced by other geologic factors such as roof rock lithology and competency, and location with respect to local fold structure.

Jan 1, 1989

By T. A. Evans

The Bureau of Mines conducted a Laboratory and pilot-plant investigation of the flotation of iron sulfides from zinc-lead mill tailings near Platteville, in south-western Wisconsin, at the North Central Experiment Station, Minneapolis, Minn. The procedures used and the results obtained in this investigation are described in this report. Samples for laboratory tests were obtained from each mill in the district, namely, Calumet & Hecla, Inc., Eagle-Picher Co., Vinegar Hill Zinc Co., and Tri-State Zinc, Inc. The sample fat pilot-plant work was obtained from the Davis Mining Enterprises mill.

Jan 1, 1957

By Ellis S. Hertzog

The data published in this retort cover only one phase of a special study of tile physical and chemical properties s of only Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, and ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability, test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This caper makes available for the first time fairly comprehensive3 information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors Lave included a, complete description of it in this report.

Jan 1, 1938

By G. W. Birge, D. E. Wolfson, J. G. Walters

Seventeen samples were carbonized by the BM -AGA pilot - plant test method and in industrial ovens . Chemical and physical properties of the samples were determined , and the physical properties of the cokes prepared by the two methods were compared . Since the capacity of the plants from which these samples were obtained is about 30 percent of the 1959 total for the United States , the data given in this report are indicative of the chemical and physical properties of blends used to produce industrial cokes and the acceptable chemical and physical properties of the resultant coke .

Jan 1, 1964

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960

By Roy Greenfield

Estimates are given for the distance from a seismometer at which a miner can probably be detected. The procedure in making these estimates was to first establish the natural noise levels at the output of a surface seismometer for the 25 to 100 Hz frequency passband. The noise levels give the range of values which may be expected in areas with no man-made noise. For each noise level, we give the detection threshold which, when exceeded, indicates that a signal has been received. Based on the signals recorded by Westinghouse, curves are given which show the peak signal amplitude as a function of source- to-receiver distance (slant range). Curves are given for the Westinghouse seismic thumper, a 50-pound timber, and a sledge. For a given type of source, the receive signal strength depends more strongly on slant range than on any other factor. However, there is approximately a five-to-one scatter in the amplitudes. Thus, further study of factors affecting the signal amplitude might allow better estimates to be made for any particular geological setting. Combining the signal amplitude with the detection thresholds for the different noise conditions gives the distances at which a miner should be detected. These are given in Table l* below. [ ] The text also gives the increase in detection ranges which should occur if steps are taken to increase S/N by 10 dB. We feel that 10 dB is a conservative estimate of the improvement possible. During an actual rescue operation, the seismic crew and system should be capable of making on-site estimates of their detection capability, based on measurements of the site noise, and upon the best available estimates of the

Jan 1, 1974

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By G. W. Jones

The determination of the ignition temperature of diethyl ether and ethylene in air and omen which is described in this report was made primarily for comparison with similar determinations of other compounds in the same apparatus and using the see laboratory technique. The investigation was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines with the cooperation of Merck & Co., Inc.

Jan 1, 1935

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

By Jr. East

The Bureau of Mines conducted an investigation of the Nightingale tungsten deposit about 38 miles north of Fernley, Nev., from September 1939 to March 1940, to determine possible resources of tungsten ore. The property was owned by the Gold, Silver & Tungsten, Inc., which maintained its offices in Boulder, Colo. Ore was discovered in 1917, and some ore was mined in 1918 and treated in a mill at Toulon, a station on the Southern Pacific Railroad, 40 miles east. Same shipments were made since 1918, but no production figures are available. The ore is mined from nearly vertical tactite bodies at the limestone-granite contact. The Bureau of Mines excavated 944 linear feet of trenches, drifted 52 linear feet, sunk a shaft 20 feet in depth, sampled the underground workings by cutting 743 linear feet of channels, sampled the surface trenches by cutting 415 linear feet of channels, and drilled 9 diamond-drill holes, totaling 3,000 feet. The ensuing sections note the location and physical features of the district and specify the property and ownership. The history of the mine is briefed, and the geology and mine workings are described. The work done by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and a table of sample analyses in appendix B.

Jan 1, 1950

By Charles L. Kimbell

Comprehensive world mineral industry investment data do not exist, but limited material published on aggregates of in vestment in some elements of the world mineral industry suggest a continued up-turn in the investment level, at least in market economy countries in 1989. Steel industry investments in Organization for Economic Cooperation and Development (OECD) countries are not yet available for 1989 but, as shown in table 6, increased by 22.1% in 1988, after showing a decrease of 5.2% (revised) in 1987. The pattern of investment ups and downs varied during 1988 within country blocs and economic alliances showing no particular trends. Investment in the steel industry by the United States increased by 58.3% between 1987 and 1988 and was 1 1.9% higher than the previous highest amount invested during the 1984-88 period but was still 41.5% less than the amount invested in 1983. Investment in the steel industries of the European Coal and Steel Community (ECSC) dropped again in 1988 from the revised amount for 1987, which became the first drop after several years of steady growth in what became the expanded ECSC in 1986. This drop in 1988 was the result of lower investments by Denmark, France, the Federal Republic of Germany, Ireland, Italy, Luxembourg, the Nether- lands, and Spain, investments grew or remained level in Belgium, Portugal, and the United Kingdom in 1987 and 1988. A decrease in investment in the Canadian (-26.6%) steel industry was offset by in- creases registered by the members of the European Free Trade Association (EFTA) of 31.7%, by Japan of 19.8% by Turkey of 22.4%, and a slight increase by the nations of Latin America. If data for the world steel industry as a whole, including those of the centrally planned economy countries, were available, the same pattern presumably would be shown as that reported; that is, it would remain fairly stable, with increases in some countries being offset by decreases in others. However, the lack of comprehensive information on the centrally planned economy countries makes it impossible to determine whether the overall trend was up or down despite recorded increases or decreases in production of the materials involved. Preliminary data show that investment levels in industries dealing with the production and/ or processing of mineral commodities for

Jan 1, 1992

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941