Search Documents

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By C. S. ROBINSON, T. M. Romslo

This investigation was conducted jointly by the Bureau of Mines and the Geological Survey to obtain further information on the source and economic possibilities of the copper mineralization exposed on the Copper Giant group of claims, Ajo mining district, Pima County, Ariz. The Copper Giant group of claims was first brought to the attention of the Bureau of Mines by Joseph Hunter (deceased), Phoenix, Ariz., part owner of the claims. In December 1942 these claims, and an adjoining group, were investigated by T. C. Denton, mining engineer, formerly with the Bureau of Mines, and Nels P. Peterson, geologist, Federal Geological Survey. It was concluded the area could not be considered as a source of copper for immed- iate emergency needs and that further investigation of the area, at the time, was not warranted. In the spring of 1948 the lessee, J. H. Greenway Albert, requested Bureau of Mines assistance in developing the property. J. H. Hedges, former chief, Tucson Branch, Mining Division, and Lincoln A. Stewart, mining engineer, Bureau of Mines, made a cursory examination of the property and noted that at numerous places, low-grade copper mineralization appeared on fractures and bedding of the Locomotive fanglomerate and Ajo volcanics, which are thought to be of Tertiary age. During the period of May 11 through 14, 1949, Bureau of Mines engineers3 mapped and sampled two areas of mineral- ization. On June 2 and 3, 1949, the areas selected by the Bureau and three other nearby mineralized areas were investigated by C. A. Anderson and R. S. Cannon, Jr., of the Federal Geological Survey. As a result of these examina- tions, further investigation of certain areas was believed to be merited. The Copper Giant area was selected as the most favorable in which to carry out exploratory and development work. The field work on the project was started in October 1949 and completed in December 1949. It consisted of road building, trenching, sampling, topo- graphic and geologic mapping, diamond drilling, and logging of core. Samples taken on the project and during preliminary examinations totaled 64, of which 63 were surface samples. Diamond drilling, started October 10 and completed December 7, consisted of two holes for a total depth of 1,542 feet.

Mar 1, 1952

By R. Hogg, T. F. Dumm, L. G. Austin, M. Yekeler

"Dedicated to Professor Kurt Leschonski on the occasion of his 60th birthdayAbstractThe kinetics of batch grinding quartz from a feed of 600 by 425 Jim to a product of 80% less than 10 µm have been determined using screening and laser diffractometer sizing for size analysis. The specific rates of breakage decreased by a factor of about three when the material became less than about 100 µm in size, but the primary breakage distribution function also changed to give proponionately more fine material, so that the grinding efficiency expressed as the development of surface area (B.E:T.) per unit of energy input did not decrease. Analysis of the shape of the particles in the 2S x 38 µm size range showed that particles of this size produced by roll crushing or by 8 minutes of grinding of a 42S x 600 µm feed were not different but at long grinding times the particles were rounded. This suggests that the breakage mechanism changes to give more chipping and abrasion and less disintegrative fracture. As the material approached the ultrafine size range it adhered to the mill case and there was no further size reduction. However, a technique for striking the mill case to dislodge the particles was successful in allowing further grinding to 400Jo by weight less than 2 µm.1 IntroductionIt has long been known that it is difficult to accomplish ultrafme grinding in a tumbling ball mill. It has been reported [12, 13] that there is no further size reduction after some hours of grinding cement clinker in laboratory ball mills. Austin and Bagga (1] and Shah and Austin [16] have given an analysis of the kinetics of dry grinding in a laboratory ball mill, introducing the concept of a slowing-down factor K, which is the ratio of the specific rates of breakage at some long time of grinding to the normal specific rates of breakage. They showed that this factor decreased as fine material accumulated in the mill charge. Cottaar and co-workers [8-10] showed that the movement of solid in a dry laboratory ball mill was influenced by the fineness of the solid and by the presence of air, and that evacuation of air from the mill caused particle sedimentation and low rates of breakage.The concept of the slowing-down factor has also been used in wet grinding [17, 18]. At very .high slurry concentrations it appears to be correlated with a steady decrease of mill power caused by the build up of a layer of deposit sticking to the mill case. This reduces the effective mill diameter and, eventually, the balls start to adhere in the layer and centrifuge. A decrease of mill power always indicates less lifting and tumbling of the media and, hence, less breakage. However, slowing-down of breakage rates was also observed at lower slurry concentrations where there was no change in mill power."

Jan 1, 1990

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By Arcy R., D&apos George

A process for removing sulfate from Great Salt Lake brines and other natural brines, including sea water, has been developed. Sulfate is quantitatively removed by precipitation as barium sulfate in a cyclic process employing ion-exchange techniques. Barium is continously recovered and recycled, and sodium carbonate and sulfur or sulfuric acid are produced as byproducts in quantities sufficient to more than defray the cost of desulfation.

Jan 1, 1967

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By T. W. Hunter

THE TOTAL production of energy in the United States in 1954 decreased 4.6 percent below 1953. The production of coal continued to decline, and the production of crude oil decreased for the first time since 1949. These decreases were partly offset by an increase in the production of natural gas. The total energy production of 35,365 trillion B. t. u. in 1954 was the lowest since 1950. [ ] This drop in energy production was consistent with the 1.1-percent decline in gross national product during the year-from 364.5 billion dollars in 1953 to 360.5 billion in 1954.

Jan 1, 1958

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972