Search Documents

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By W. E. Anable

The Bureau of Mines studied the purification of commercially available vanadium in the 100-kw electron-beam furnace. Purification studies were conducted on a 100-gram button scale by melting and holding the liquid vanadium at temperatures ranging from 2,060° to 2,080° C at pressure of 5(10)-5 torr for periods ranging from 5 to 20 minutes. The effect of doping vanadium with carbon and metallic additions was determined. This study demonstrated that hydrogen was readily removed to 3 ppm or less, oxygen and carbon were reduced to less than 100 ppm each, and the metallic impurities were reduced Co the range of 10 to 500 ppm. The nitrogen content was not reduced in any of the buttons; rather, the nitrogen concentration generally increased as samples were held for successively longer periods. Oxygen was removed much faster and more completely when vanadium was doped with small carbon additions or one of several dopes prior to melting.

Jan 1, 1967

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By McHenry Mosier

This paper describes the practice in diamond drilling blast holes and discusses the relative merits of this method as compared with drilling by percussion rock-drills at eastern magnetite mine A. The rooke that were drilled included: (1) Gneiss; (2) sohist; (3) crystalline limestone; and (4) granular masses of magnetite. The principal stoping methods were: (1) Sublevel open stoping and (2) inclined room-and-pillar. Diamond drilling was used in the sublevel stopes and in some of the large pillars in an old section of the mine. Experimental work on diamond drilling blast holes began in 1943. Drill- ing proved difficult owing to the occurrence of fingers of extremely hard barren rock in the magnetite ore. All diamond drilling was contracted to a firm that furnished everything necessary for drilling except compressed air and water. In most instances the diamond-drill machine is clamped directly to a 3.5-inch column to reduce vibration. For drilling in floor pillars in open stopes, the drill was set on a demountable, sectionalized steel, frame with four legs carrying a 20-foot, 3.5-inch, extra-heavy pipe. "Both coring and noncoring bits were tried. In holes drilled with a cor- ing bit, the core was ground into sludge as the bit advanced so that it was unnecessary to delay drilling for pulling core. Data on tests with several types of bits are given as well as some oper- ating results. A direct comparison of costs between diamond drilling and percussion drilling was not available. The advantages of diamond drilling blast holes at mine A included: (1) Safer working conditions in open stopes. (2) The recovery of additional ore. (3) A reduction in the amount of stops development.

Dec 1, 1946

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in- situ, on rock mine pillars, arches, end other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigations4/ have shown that, the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By A. L. Engel

The sample of ore on which the work described in this paper was done came from Mina Oriente, Carrizal Bajo, Provincia de Atacama, Chile, South America, and was sent at the request of the Chil.ean Government through the Foreign Minerals Division of the Bureau of Mines. This ore had been tested locally for treatment by flotation and cyanidation without satisfactory results. An additional difficulty was the absence of water near the ore deposits, so that in any treatment method considered the water requirements would have to be very low. It was desired to develop a practical method of recovering the gold and, if possible, the copper in the area. No data of previous investigations were made available. The sample received was mostly quartz, highly brecciated, with limonite and hematite in the fractures. Copper occurred as malachite and azurite, also in the fracture s and to a slight extent as a stain in the quartz. Some fine-grained pyrite with a little arsenopyrite occurred within the quartz. An occasional grain of chalcopyrite was observed. No free gold was seen during examinations of the ore, but amalgamation indicated that some was present.

Jan 1, 1949

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By Compiled by Staff

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and· approved February 25, 1913, made it the province, and duty of the Bureau of Mines to ""disseminate· information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue of the Bureau of Mines List of Publications and Articles describes reports and articles published during the period January 1, 1990, to December 31,1991. It, supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 and the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 from January 1, 1975, to December 31,1979,6 from January 1, 1980, to December 31, 1984,7 and from January 1, 1985, to December 31, 1989.8"

Jan 1, 1992

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By R. D. Leitch

"INTRODUCTION This report is another of the series on the effect of drouth and low water on the pollution of streams by coalmine drainage. A previous report3 dealt with work on Bennett Branch of Sinnanahoning Creek, Pa. This report deals with the results obtained during a similar study of Black Lick Creek, Two Lick Creek, and Yellow Creek. All of these belong to the same drainage system. Two Lick Creek is a tributary to Black Lick Creek, and in turn Yellow Creek is a tributary to Two Lick Creek, as shown in Figure 1.Black Lick Creek was of such a volume that a seasonal investigation was not entirely feasible. Yellow Creek was found to have mines only near the mouth, except a few of status unknown to the writer at the extreme head-waters, and the stream was also more or less inaccessible for regular and frequent sampling. Two Lick Creek was found to be most suitable of the three.ACKNOWLEDGMENTThe work reported has been carried on under the direction and with the advice of Dr. R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station."

Jul 1, 1931

By Robert L. Grayson, Syd S. Peng

"An airborne dust study was undertaken at a Southwestern Pennsylvania underground bituminous coal mine by the Pennsylvania Department of Mines and Mineral Industries in 1964 for the purpose of making recommendations and requirements regarding compliance with health and safety aspects of The Bituminous Coal Mining Laws of Pennsylvania, approved by the legislature on July 17, 1961. The study was designed to accurately represent the airborne dust conditions of the subject mine. Sampling by midget impinger of specific worker locations throughout the mine was accomplished. Sample analyses yielded dust concentrations to mppcf, particle size determinations in cumulative per cent less than specified cut-off diameters, and determinations of free silica percentages in total dust samples. The data from this study is further analyzed, and the results are presented.INTRODUCTIONThe Bituminous Coal Mining Laws of Pennsylvania, enacted in 1961, prompted a study of respirable coal mine dust by the Department of Mines and Minerals Industry in 1964. In recognition of their obligation for ensuring the health and safety of bituminous coal miners, the department set out to characterize the airborne dust of mines throughout the commonwealth. The purpose of the studies was to make recommendations and requirements for compliance with the law and for control of airborne coal mine dust in Pennsylvania mines.One such study was undertaken at an underground bituminous coal mine operating in the Pittsburgh Seam in Southwestern Pennsylvania. The study was desig11ed to sample specific worker locations throughout the mine site and characterize the respirable dust relative to each of them. A midget impinger was used to gather respirable range dust samples during an 8-hour shift. Continuous miner operator, roof bolter, stoper bolter, loading machine operator, shuttle car operator, gathering motorman, mainline motorman, and rotary dumper jobs were sampled underground. In addition, barge mover, coal sampler, fine coal operator, heavy media operator, and boiler room attendant occupations were sampled on the surface. The surface sampling was over a 71-hour shift because of UMWA contract provisions."

Jan 1, 1988

By G. W. Jones, F. E. Scott

"INTRODUCTION During the last war, considerable attention was given to the search for materials or combinations of materials for use as expelling agents for aerosols in the well-known ""aerosol bomb."" These materials must be free of fire and explosion hazards under normal conditions of use.In cooperation with the Department of Agriculture and other Federal agencies interested in the work, the Bureau of Mines carried out a laboratory investigation on the inflammability of- dimethyl ether-dichlorodifluoromethane air mixtures. 4/The method of investigation was essentially the same as that used in a similar investigation dealing with the inflammability of propane-butane-dichlorodifluoromethane mixtures. 4/SOURCE OF MATERIALSThe dichlorodifluoromethane (commonly known as freon-12) and the dimethyl ether were supplied by Dr. Lyle D. Goodhue., U. S. Department of Agriculture, Beltsville, Md. It was reported that the freon-12 was manufactured by the Kinetic Chemical Co. Wilmington, Del., and the dimethyl ether by the Carbide & Carbon Chemicals Corp., Charleston, W. Va..The materials were obtained in small metal cylinders and were used as received. Before using, the cylinders mere placed in an upright position, and 5 to 6 liters of the gas was released from each cylinder to the atmosphere to remove any trapped air that may have been introduced when the cylinders were filled."

Sep 1, 1947