Search Documents

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

By R. H. Nielsen

A new, cheaper precipitation scheme has been developed to produce purified zirconium oxide, Technical-grade sulfuric acid is used to precipitate a basic zirconium sulfate from a hot dilute hydrochloric acid solution. With close control of temperature, pH, and zirconium - sulfate ratio, excellent purification and complete zirconium recovery can be attained. The process has been successfully applied for 3 months and has proved to be a more satisfactory procedure than the ammonium phthalate process used previously. INTRODUCTION The Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines has developed and improved the Kroll process for the production of pure ductile zirconium and hafnium. metal. Since 1946 over 1 million pounds of zirconium sponge metal has been produced, mostly high-purity material for the Atomic Energy Commission

Jan 1, 1956

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By Charles S. Allbright

This report describes hydrogenation of petroleum distillate fuels in bench scale equipment and the effects of hydrogenation on the storage stability and the composition of the fuels. Two distillate fuels were hydrogenated in laboratory equipment using a commercially available cobalt molybdate catalyst. Reactor temperatures were varied from 600° to 850° F and pressures from 100 to 600 psig. Product fuels were analyzed by ASTM, Bureau of Mines, mass, and infrared methods. Hydrogenation of a catalytically cracked fuel from Oklahoma crude oil significantly improved the storage stability, reducing insoluble gum formed during 9 months of storage at 110° F from 19.0 to 1.3 mg per 100 ml fuel, average. Conversion of the olefins to other hydrocarbon types varied with the temperature of hydrogenation--at 700° to 850° F the conversion was mainly to aromatics, at 650° F about 50:50 to saturates and aromatics, at 600° F principally to saturates. Processing a fuel composed of a mixture of virgin distillate and catalytically cracked stock, both from Illinois crude, at 700° F and 200 psig effected marked improvement in stability; the buildup of insoluble gum in storage was lowered from 18.3 to less than 1 mg per 100 ml fuel.

Jan 1, 1967

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By Jack C. White

This U.S. Bureau of Mines report assesses the resource potential of trace metals present in commercial Ti mineral concentrates. Metals of greatest interest: are those defined as "strategic and critical" by the U.S. Congress in 1981. Metals of interest in Ti mineral concentrates are Cb, Cr, Ta, Th, U, V, and Zr. Commercially available Ti mineral concentrates were studied. Characterization and analysis of major and minor constituents were performed by X-ray diffraction, neutron activation, inductively coupled plasma emission, atomic absorption, and classical wet chemical techniques. Of the metals investigated, the Cb, Ta, and V content of some concentrates may be a significant potential resource, depending on their amenability to recovery.

Jan 1, 2010

By J. F. Papp

The microstructures of a CF2Br2-inhibited methane flame and its uninhibited analog have been determined using molecular beam-mass spectrometry. The slightly lean flames were stabilized on a cooled porous plug burner at reduced pressure. Composition profiles of stable, intermediate, and radical species and temperature profiles were obtained. Comparisons of the uninhibited and inhibited flame profiles revealed the following inhibition effects; a shift of the primary reaction zone to higher temperatures, a higher maximum flame temperature, an increase in the CH3 concentration, and a reduction in the H2CO, H, 0, and OH concentrations. Kinetic analyses of the data yielded rate coefficients at flame temperatures for the reactions H + CH4 ? CH3 + H2, H + O2 ? OH + O, CO + OH ? CO2 + H, and CH3 + O ? H2CO + H. CF2Br2 is judged to decay by thermal decomposition and abstraction reactions.

Jan 1, 1981

By S. H. Katz, J. J. Bloomfield

Fires in zinc dust have sometimes given particular trouble owing to their resistance to extinguishers and the liability of explosions . Similar problems , notably with aluminum dust* , have previously been subjects of investigation by the Bureau of Mines .

Mar 1, 1922

By James Westfield

This report covers the calendar year 1954 and has been prepared and submitted to the Congress of the United States in accordance with the provisions of Sec. 106(a) and Sec. 2l2(c) of the Federal Coal-Mine Safety Act (66 Stat. 692; 30 U.S.C. Sec. 451-483). Background The Federal Coal-Mine Inspection program was established to carry out the provisions of Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. This act has since been amended to be known as Title I -Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also includes Title II -Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal-Mine Safety Act.

Jan 1, 1956

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By V. A. Nieberlein

Problems of design involving the high-temperature characteristics of materials of construction have focused attention on tungsten, the metal with the highest melting point. To study the properties of this metal a method was needed to produce tungsten of high purity easily and consistently. The Bureau of Mines has made tungsten metal in massive form on a laboratory scale by hydrogen reduction of tungsten hexafluoride (WF6). Metal made in this manner had a purity of 99.99 percent or better, with reference to all detectable impurities, including gases. The process tolerated a wide variation in operating conditions, and the results with respect to total impurities as low as 0.01 percent were reproducible.

Jan 1, 1959

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959