Search Documents

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By John J. Mulligan

Since 1941 the Federal Bureau of Mines has been conducting an intermit-tent program of placer and lode investigations to evaluate the potential tin resources of the western Seward Peninsula tin belt. Previous investigations were made in the Potato, Cape, Brooks (Lost River), and Ear Mountain areas. As part of this program the Bureau made a reconnaissance of reportedly tin-bearing stream gravels in areas adjacent to the previously worked tin deposits at Lost River and Potato Mountain. The objective of the reconnaissance was to determine if additional areas might be favorable for lode or placer exploration. The work was begun late in the fall of 1956 and completed during the following summer. The streams sampled were the Lost River and York Creek in the Brooks Mountain area and the Anikovik River and Kigezruk and Baituk Creeks in the York area. Samples were obtained by churn-drilling methods employing conventional placer-evaluation procedures. Holes were drilled at wide intervals at sites chosen as being representative of drainage areas rather than of individual gravel deposits. Minor to trace amounts of tin were found in the gravels of all these streams, but the highest grade was 0.35 pound of tin per cubic yard in the gravels of Lost River below the mouth of Tin Creek. Small amounts of gold were found on Baituk Creek and in one hole on the Anikovik River; the highest grade did not exceed 10 cents per cubic yard. Traces of scheelite and barite were found on York Creek, chromite was encountered in one hole on the Anikovik River, and minor amounts of titanium minerals (probably derived from basaltic intrusives) were found in the York area.

Jan 1, 1959

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,938,200 for the 1.03-million-ton-per-year (MJ.Vl tpy) mine to $31,435,500 for the 3.09 MM tpy mine. Total capital investment ranges from $21,607,200 to $51,982,000 for the same mines. Corresponding selling prices for the coal range from $9.11 to $8.06 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By Lulie H. Crump

U.S. supply and demand data for dry natural gas by source, form, and major consuming sectors--within and between States and defined regions--were tabulated for the years 1960 and 1965. State-by-State quantitative data are provided for the natural gas industry that can be arranged into regional groupings and used to determine regional flow patterns. The tables show the derivation of the total supply of gas available for consumption from total marketed production. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, transportation, and electricity generation, utilities). The summarized data show an increase in the absolute demand for natural gas in all regions for the period 1960-65, although the relative posit ions of the various subregions, with respect to national consumption, remained about the same. To enable comparison of data on dry natural gas with data on other energy sources, quantities in terms of million cubic feet were converted to British thermal unit (Btu) equivalents.

Jan 1, 1969

By Warren Howes, A. B. Campbell, W. H. Ode

"INTRODUCTION The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation.The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry, Missouri School of Mines and Metallurgy, and Will H. Coghill, supervising engineer of the ore dressing section of the United States Bureau of Mines.ORIGIN OF ACID MINE WATERSRain water, carrying oxygen and carbon dioxide in solution, finds its way into the pores and crevices of the earth's crust and percolates downward through the rocks. This water and its dissolved gases exert a solvent action on many minerals, the extent of which depends upon the nature of the associated minerals.The iron sulphides are the chief sources of the 'trouble with sulphates and sulphuric acid because they oxidize so freely and contain more sulphur than is required to satisfy the iron when ferrous sulphate is formed. Galena and sphalerite may oxidize to sulphates without liberating acid. A few of the common reactions occurring in the Tri-State mine waters may be illustrated by the following equations:"

Mar 1, 1932

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By P. D. Kovscek

The performance of a novel prototype kerf-cutting impact mining machine was evaluated under a cooperative agreement between the U.S. Bureau of Mines and RAMEX Systems, Bellevue, WA, while operating under conditions typical of normal tunnel entry development. Selected operating parameters were monitored concurrently to determine baseline operating conditions and to study relationships between operating parameters. Using the data obtained, the specific energy requirements of the impact mining machine were calculated and compared to specific energy requirements of tunnel boring machines cutting in rock having similar hardness. Tests results indicate that the kerf-cutting impact mining machine can provide a mechanical means for mining very hard rock that cannot be effectively mined using commercially available mechanical excavators.

Jan 1, 2010

By E. P. Youngman

A new mining law for the Recublic of Polend was promulgated by presiden- tial decree dated November 29, 1930, published in the Journal of Lews (Dzienni stex) No. E, text 654, December E, 1530, and wes to become effective January 1, 1932, in all Polend except Silesie. Its adoption in Silesia wes dependent pon the action of the Silesian Diet. As the new law is considered an im- provement over the old Austrian Mining Lew, which is operative in the Silesian districts of Bielsk and Cieszyn, and the Prussian Kining Law, which is opera- tive in Upper Silesia, no delay in its adoption for Silesin was looked for. This new law codifies the various juridical regulations pertaining to ines existing in different parts of the Polish Republic but does not include legislation with respect to the extraction of minerel oil, especially crude oil. Petroleum legislation was postponed to a later date in order to facili- tate codification in other fields. Koreover, as the oil industry exists in Galicia elone, deley will not be detrimental.

May 1, 1932

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

[ ]

Jan 1, 2011

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962

By Charles D. Litton

Experiments were conducted to determine the optical scattering properties of diesel particulate matter (DPM) and various combustion aerosols from both flaming and smoldering combustion sources at discrete angles of 151 and 301 in the forward direction and at a light source wave length of 635 nm using a simple light scattering module. In addition to the scattering data, simultaneous measurements were made of the total aerosol mass concentration; light extinction at an average wave length of 546nm; and the response of a common bipolar ion chamber typical of residential smoke detectors modified to allow the aerosols to flow through the chamber. The results of these experiments indicate, for DPM and combustion aerosols, the intensities per unit mass concentration depend not only upon whether the aerosolis DPM or combustion aerosol but also upon the type of combustion aerosol. The results also indicate that the ion chamber responses are greatest for DPM, followed by the response to flaming combustion aerosols (FCA)and lowest for smoldering combustion aerosols (SCA). For light scattering, the greatest intensities are found for SCA, followed by the intensities from FCA, and lowest for DPM. This report describes the experiments, their results, and the use of these results to developed sign criteria for early warning fire sensor capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by the products produced from diesel engines. © 2002 Elsevier Science Ltd. All rights reserved.

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962