Search Documents

By Hugo E. Camargo

Noise Induced Hearing Loss is the most common occupational disease in the U.S. and of paramount importance in the mining industry. According to data for 2006 from the Mine Safety and Health Administration (MSHA), Continuous Miner operators accounted for 30.2% of underground mining equipment operators with noise doses exceeding the Permissible Exposure Limit (PEL). This figure becomes more significant considering that 49% of the 2006 national underground coal production was extracted using continuous mining methods. Thus, there is a clear need to reduce the sound radiated by Continuous Mining Machines. The first step towards efficient noise control of a Continuous Mining Machine requires identification of the various noise sources under controlled operating conditions. To this end, a 42-microphone phased array was used in conjunction with 4 reference microphones to sample the acoustic field of a machine in the Hemi-anechoic chamber of the Pittsburgh Research Laboratory. These data were processed using a frequency-domain beamforming algorithm to obtain acoustic maps of 5 sides of the machine. The focus of the test was on the conveyor noise since previous studies showed that operation of the conveyor is the most important contributor to the sound radiated by the machine. From the acoustic maps, the following potential areas for noise control were identified, and included: chain-tail-roller interaction, chain flight tip-side board interaction, and chain-upper deck interaction.

Jan 1, 2008

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By Oliver Bowles

"On January 15, 1920, a man was killed by falling rock in a limestone quarry in Utah. The quarry was visited by a representative of the Industrial Commission of Utah, and the cause of the accident was carefully determined. The facts concerning this accident, and the Bureau's recommendations are given in some detail in the hope that quarrymen may take steps to avoid dangerous conditions, and thus reduce the liability to accident.The quarry rock face is about 180 feet high, and the ledge is covered with an overburden of 10 to 20 feet of a mixture of soil and boulder. The rock face is not vertical, but slants at an angle of about 45° to 50°, while the stripping face stands at an angle of 70° to 80°, and is flush with the rock face. The conditions are shown in the accompanying figure.The man who was killed was employed in breaking rock at the foot of the quarry wall. The sun had been shining on the stripping face, and probably thawed the ground, thus permitting a boulder weighing about 20 pounds to roll down the slanting face, striking, and almost instantly killing the workman who was working with his back toward the quarry wall."

Feb 1, 1920

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Feb 1, 2005

As a basis for recommendation and for instruction of bureau engineers the considered opinion of the bureau is expressed in "decisions" of its Mine Safety Board, approved by the Director. Ten of these decisions were discussed, in Information Circular 6091.3 Decision No. 11, approved by Scott Turner, Director, on February 28, 1929, is as follows: "In the interest of safety, the Bureau of Mines, Department of. Commerce, recommends that in coal mines, haulage and (or) hoisting be kept in intake air as far as possible." As in the case of previous mine-safety decisions, the subject matter covered by this decision has frequently come to the attention of the Bureau of Mines through the reports of its mining engineers on explosion disasters and in accident-hazard investigations.

Jan 1, 1929

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By Michael Sokaski

The Cliff Springs prospect in the northern part of the Slate Range Wilderness Study Area (WSA) contains only minor amounts of gold and silver. Clay near this prospect contains insufficient aluminum to be of economic interest, although alunite claims are recorded in the vicinity. Mineralized rock at the Crescent Mine adjacent to the WSA contains gold, silver and lead occurrences. The host rock may be present in the extreme southwestern part of the WSA, which is covered by alluvium. Substantial sand and gravel deposits are present but these occurrences are remote from markets. Much of the USA is underlain by volcanic rocks and alluvium and consequently the mineral resource potential there remains unknown.

Jan 1, 1983

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920