Search Documents

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By J. W. Faul

[The Bureau of Mines initiated an extensive research on coal-mine ventilation factors in 1922, large- scale tests being conducted in its experimental nine near Bruceton, Pa., over a period of two years. A comprehensive report an this work is in course of preparation, but in order to place the practical results before the mining fraternity immediately and in condenses form, the more important features will be presented in a number of short papers. The present report is the first of a series dealing with the resistance of coal-mine entries to the flow of air and considers only entries in which there are no obstructions other than the natural roughness of the ribs, roof, and floor.]

Jan 1, 1924

Provide an inexpensive, remote actuated, stench-gas system which reduces fire warning time to underground work locations. Approach A mine's pager phone hard-wire network is used to release stench gas from pressurized canisters located near working areas. The release is initiated by placing a coded message into a control phone at some central location. How It Works Currently, in most mines, the decision to release a warning stench gas is made by mine management after communication from the mine of a fire or similar potentially dangerous situation. Stench gas is then released into the ventilation air and/or compressed air lines for dissemination throughout the mine. This can result in significant delays in warning time. Often, surface personnel must travel to distant shafts, or other release points, wasting valuable time. Also, the time for ventilation air to circulate from the surface to working locations can be long and the effectiveness of compressed air as a stench transport agent depends on whether the compressed air is being used at the face. The Bureau of Mines, through a contract with MSA Research Corporation, has designed and tested a warning system which avoids these problems. The system consists of multiple, pressurized stench-gas canisters located under-ground in the mine-ventilation network so as to provide quick dissemination of the released stench gas to working areas. Each stench-gas canister is hard-wire connected to a nearby pager phone and from there to a control phone at the surface or at a central in-mine site. In the event of a mine emergency, the canisters are activitated to release stench gas by placing a coded message into the control phone. A low amperage Signal sent from the control phone to the receiver phone closes a relay, which activates a release mechanism on the canister.

Jan 1, 1984

By Paul Hatmaker

"The Bureau of Mines recently has issued a general information circular covering briefly the origin and occurrence, properties, uses, exploitation, and marketing of diatomite. Since this publication was prepared, additional information has become available regarding one of the newer uses of diatomite — that as a filler in battery boxes. As this market is rapidly becoming one of the important outlets, a brief discussion of such use may be of interest.Diatomite is a mineral substance composed principally of the skeletal remains of diatoms. The skeletons of these microscopic flowerless water plants are made from silica present in the water in which these tiny plants live. The minute shells or ""casts"" accumu¬late in the bottom of lakes, ponds, or inland seas, and eventually become more or less consolidated into beds of diatomite.The uses of diatomite depend largely upon its peculiar properties. Diatomite is a highly porous substance and possesses marked absorptive powers. The large percentage of pore space makes the material very light in weight. It is relatively insoluble in most solutions.The largest deposits in the world are found in California, but diatomite occurs in many other Western States and also is found in a number of places along the Atlantic seaboard. Outside of the United States diatomite occurs in many countries; Algeria and Germany are among the largest producers.Usually diatomite is mined either by underground or open—cut methods. In some instances it may be dredged from lake and swamp bottoms. It must be dried prior to grinding or other preparation for market, and for many purposes must undergo a complex sizing and grading system for removal of such impurities as sand and clay and for classification of the material to the various sizes desired,"

Mar 1, 1931

By T. T. Read

"Employee representation in the management of large mining enterprises was first introduced in organized form, by the Colorado Fuel and Iron Co. in 1915. Within the past few years a number of the larger mining enterprises have introduced similar systems and there is growing interest in the subject. This will be stimulated by the final report of the President's Second Industrial Conference, in which the following statement occurs:""The conference finds that joint organization of management and employees where undertaken with sincerity and good will has a record of success. The general principles governing such organizations are stated at length under the title 'Employee Representation. It is not a field for legislation, because the form which employee representation should take may vary in every plant. The conference, therefore, does not direct this recommendation to legislators but to managers and employees.""If the joint organization of management and employees in the plant or industry fails to reach a collective agreement, or if without such joint organization, disputes arise which are not settled by existing agencies, then the conference proposes a system of settlement close at hand and under Government encouragement, and a minimum of regulation. The entrance of the Government into these problems should be to stimulate further cooperation."""

Mar 1, 1920

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

This report describes the development, installation and performance of a lonpwall illumination system. The longwall illumination system was installed at the Greenwich Collieries 112, Cockport, Pa. It utilized flourescent luminaires, intrinsically safe power distribution and is the first longwall system installed in Pennsylvania.

Jan 1, 1976

By Rudolf E. Grauer

[ ]

Jan 1, 1981

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Recently, a collection of programs that will simulate a ventila¬tion system with extensive analyses and report-generating capabilities and error diagnostics has been developed (Didyk, 1974). It has pro¬visions to handle air injections, methane or gas emissions, and leakage. Additionally, it will solve problems where fixed and/or maximum air quantities are specified for some airways. Finally, the simulator has been structured to be extremely modular so that additions and revisions to the model can be easily made. The general aspects of the information flow and logical structure of the mine ventilation simulator are shown in Figure 14. The output from the methane emission model is input into the ventilation simulator for calculation of the concentrations in all branches of the network. The methane model and the ventilation simulator provide powerful tools for the analysis and planning of mine ventilation systems. INPUT DATA REQUIREMENTS In all of the mathematical models, several coefficients that de¬fine the characteristics of the ventilation system are used. For the ventilation simulator, these include the frictional characteristics of the ventilation regulatory devices. Considerable work has been done on the experimental determination of these coefficients for smooth pipes and well-defined mediums, but only limited data are available for actual mining conditions. FRICTION FACTORS: The frictional characteristics of mine airways affect both the dispersion of pollutants and air flow through the roadways,. They

Jan 1, 1975

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By H. B. Freaman, C. L. Colburn, C. M. Bouton

"The mine telephone has been perfected to such an extent that it is giving satisfaction in most mines were the wiring is well insulated. Very often the telephone cannot be depended upon on account of falls of rock, grounding due to worn insulation or extreme dampness. In the event of a disaster it frequently happens that the mine telephone system is put out of commission by the agency that causes the disaster, at the time when it is most urgently needed. On this account the mining industry is interested in any kind of telephone system that can be counted upon in an emergency. Many requests have been received by the Bureau of Mines to devise means of utilizing wireless methods for this purpose.The results of some preliminary experiments conducted by the writers at the Bureau of Mines experimental mine at Bruceton, Pennsylvania, in the ordinary sending and receiving of radio waves through earth strata are described below. The experiments were made in cooperation with the Westinghouse Electric end Manufacturing Co., which assigned to this work three of its radio engineers, C. A, Boddie, E. C. Douglas, and F. D. Fessler,The preliminary experiments consisted first in receiving signals from without the mine by means of a receiver located inside the mina, and second, both sending and receiving messages underground through the strata. It was found that with a receiving instrument set at a point 100 feet underground, signals from KDKA station, of the Westinghouse Electric and Manufacturing Co. East Pittsburgh, Pa., could be heard distinctly. Station KDKA is at a distance of about 18 miles from the experimental mine. About 50 feet from the receiving station used in this test was a 6-inch bore-hole from the surface, lined with iron pipe and containing electric light wires which extended therefrom through-out the mine. The presence of these wires evidently assisted greatly in the reception, for when the receiving set was carried to another point in the mine removed from wires and tracks the signals were barely audible through 50 feet of cover. The fact that signals were detected, however, even though faintly, is sufficient evidence of transmission through the ground to encourage further experimenting.In sending waves underground the Westinghouse 20-watt B.T. model T.F. transmitter was used in such a manner as to send out continuous waves of 200 to 300 meters length."

Oct 1, 1922

By Robert W. Freedman

This report describes sampling and analytical procedures used for measurement of sulfates in diesel tailpipes and in the diluted exhaust within dilution tunnels. A variety of methods exist for sulfate analysis for such systems, including ion exchange. Two chemical methods used by the Bureau of Mines are described in detail. These are based upon spectrophotometric measurement of chloranilic acid using barium chloranilate. The procedures are rapid and relatively inexpensive. In general, ion exchange is preferred by many analysts for sulfate analysis. However, it is more complex and expensive than chloranilic acid procedures, which are adequate for exhaust analysis.

Jan 1, 1982

Protect rescue workers fighting fires or mine personnel temporarily working in hot environments from heat stress. Approach A specially designed ice-cooled vest is worn while working in hot environments where cooling the mine air is not possible. How It Works The vest holds a total of 44 individual ice cells in packets that are firmly held near the wearer's skin. These ice cells remove heat from the wearer, reducing heat stress and increasing comfort. The locations of the ice cells and packets are shown in the diagram. The vest is constructed in three layers with the outer layer being aluminzed fiberglass cloth. Its aluminized surface reflects radiated heat, and its fiberglass cloth provides fire resistance and strength.

Jan 1, 1979

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By K. Clifton, K. Kar, M. Gautam, J. T. Jurewicz

"This paper describes the history of LDV measurements employed in research involving gas-solid flows. Much of the discussion deals with measurement techniques employed to obtain separate and simultaneous solid and gas phase velocities. Also, LDV based measurement techniques that arc used to obtain particle size and concentration information in conjunction with the velocity measurements arc presented.INTRODUCTIONThere are numerous examples of industrial processes in which the motion of a solid or droplet dispersed phase in a suspending gas phase is critically important. The applications range from spray droplets injected into combustion chambers to the understanding of the time release mechanisms of particles generated by dissolving pharmaceutical tablets. In many of these processes, the heat, mass, and/or momentum transfer between the dispersed phase and the suspending fluid arc the items of interest. In the past, much of the phenomena were characterized by empirical models derived from flow averaged measurements. Gradual developments in laser Doppler velocimetry (LDV), have provided researchers with an unobtrusive measurement technique capable of obtaining the particle size velocity and concentration with good spatial resolution.In the two decades that LDV instrumentation has been available, most of the uses have concentrated on single phase fluid flow measurements. The light scattered from seed particles small enough to follow complex fluid motions, including turbulence, is converted into velocity information. While the utility of this instrument in single phase flows has been demonstrated beyond question, the use of LDV in gas-solid multiphase flows has had a more gradual development. The measurements ·of interest in these flow regimes are usually the velocity of the suspending fluid as well as that of the dispersed particulate phase. Early investigators were quick to see the potential of this instrument for measurements in gas-solid flows. The interest soon expanded to the development of instruments that could also simultaneously measure particle size and concentration within a two-phase flow field.This paper tracks the historical development of LDV technology as applied to gas-solid flows. The techniques to measure particle velocity, size, and concentration arc treated in separate sections although much of the development occurred simultaneously. Finally, some unique applications conducted at West Virginia University and other locations will be discussed in the application section."

Nov 1, 1995

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

A mineral survey of the Rough Hills WSA (Wilderness Study Area) in northeastern Nevada was done by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The WSA is comprised of 6,685 acres of mountainous, desert lands within the Elko District of the Bureau of Land Management. The survey entailed investigations of prospects or mineral occurrences to provide information on possible resources within the WSA. No mineral resources were identified in the WSA. The only historical mining activity was for placer gold at the Prunty prospect at the confluence of Copper Creek and the Bruneau River. Total gravel at the prospect is about 6,500 cubic yards; however, the survey showed significant gold values (greater than $0.10 gold per cubic yard) only in the southwestern portion. There, however, the gravel averaged less than $1.00 gold per cubic yard, and only about 3,000 cubic yards are present, a grade and yardage insufficient to be of commercial interest. The occurrence, however, may have value for recreational mining by hobbyists.

Jan 1, 1986

By Joseph T. Singewald

The term "titaniferous magnetite" is used to designate those mag- netic ores of iron that carry more than 2 or 3 per cent of titanium. Large and easily workable deposits of these ores occur in different parts of the world, and have attracted attention for many years. Under present furnace practice, however, the smelting of these ores is both difficult and expensive, and for that reason they are not accepted by furnaces, so that the deposits are practically worthless. The problem of finding a feasible method of utilizing these ores has naturally been attractive, and numerous attempts have been made to solve it. Experiments to that end embrace two lines of investigation. The one that has been the more frequently tried is the elimination of the titanium from the ores, so as to make possible their smelting in the usual way. The other is the devising of a method of smelting by which titaniferous ores may be reduced as economically as are non- titaniferous ores. The former method involves a physical process, the latter a chemical process. The measure of success attainable by the first method depends entirely on the relations between the iron and the titanium in the ore. Views in regard to these relations have been divergent. Some investi- gators have believed the titanium to occur as a part of the magnetite molecule, in which case, of course, any process of mechanical separa- tion would be impossible. Others have believed that the titanium occurs as the mineral ilmenite, and that the ores are aggregates of magnetite and ilmenite. In this case a separation of the two minerals is theoretically possible. Magnetite is highly magnetic; ilmenite is nonmagnetic or only feebly magnetic. Crushing and magnetic con- centration should separate them. Numerous experiments in mag- netic separation have been made with various degrees of success, but rarely has more than a very imperfect separation been obtainable. In other words, some of the titanium exists in a separable form and some in an inseparable form, and the ratio between the two forms is

Jan 1, 1913