Search Documents

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Thomas H. Dubaniewicz

Thirteen miners died as a result of 2 explosions in the Jim Walter Resources No. 5 mine near Brookwood AL in September 2001. Both explosions were ignited in intake air entries, and both were probably ignited by electrical equipment. With few exceptions, permissible equipment is not required in intake air entries of US underground coal mines Researchers with the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. studied the electrical equipment ignition sources for the Brookwood and other w disasters to develop recommendations for preventing similar disasters Adherence to National Electrical code® requirements for flexible cords installed in hazardous (classified) locations may have prevented the second massive Brookwood explosion. The 30 CFR Part 7 requirements for battery assemblies should be reevaluated, taking into consideration United Mine Workers of America recommendations and the Zone 1"increased safety" standard requirements for battery assemblies, Class 1 Division 2 or Zone 2 explosion protection techniques are recommended for intake air equipment so that they do not present a methane air ignition source under normal operation before mine power is shut down during emergencies Battery powered circuits intake air that are likely to remain energized during emergencies should be protected by more stringent protection techniques, to protect rescue/recovery personnel. Index Terms -Class 1 hazardous location, mine explosion, flexible cord, battery assembly, permissible equipment

By Jay D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings for drifts used in block caving stopes. Design data are given that consist of moment, thrust, and deformation coefficients from which bending, axial, boundary stresses, and structural deformations can be determined at any point on the lining. Data is given for circular, horseshoe, and rectangular linings, each with two different thicknesses and subjected to eight different loading conditions for drifts excavated in hard and soft rocks. The structural analyses performed are based on procedures that account for both the structural behavior of the lining and that of the drift and take into consideration deformational interaction that occurs between them.

Jan 1, 1973

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By T. SPOLAN, G. W. Jones, R. E. Kennedy

Information relative to the explosibility of acetylene at elevated pressures and means of handling acetylene safely under these conditions is of considerable interest at present. American practice limits the pressure at which acetylene may be generated and distributed to poiIits of' use. The pressure in portable acetylene generators is 15 pounds per square inch gage. Tests made by the Bureau of Mines have shown that 15 pounds per square inch gage is too high to prevent explosiofiS of gaseous acetylene in the absence of air; in fact, dry acetylene gai can be exploded at pressures greater than 5.9 pounds per square inch gage. The Bureau has been interested in the explosibility of acetylene for many years because of its continued: use for illumination in many metal mines and its general use in cutting 1illd~--eldifigoperations in the mining maus-try.

Dec 1, 1948

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By C. H. Johnson

The Big Jim mine of the United Eastern Mining Co. is at Oatman, Mohave County, Ariz. Oatman is in the foothills on the western side of the Black Mountains, at an elevation of about 3,000 feet. It is on a paved highway about 30 miles west of Kingman, the principal distributing; center for mining supplies in the district, and 25 miles from Topock, en the Colorado River. Both latter towns are stations on the Santa Fe Railroad; Oatman has no roil connection. Mining conditions are typical of western Arizona; water is scarce, no mine timber is available locally, and the winters arc mild and the summers hot. The supply of a killed labor is usually adequate, but in 1933-34 it w not more than sufficient for the restricted operations. Wages have been $4.00 to $4.50 for miners. Electric power was supplied from Kingman and cost about 2.6 cents per kilowatt-hour.

Jan 1, 1935

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007