Search Documents

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By A. C. Fieldner

The Bureau of Mires in its investigations of gas masks for use in mines and allied industries has studied and developed various types of masks for protection against noxious uses and furies that may be present in atmospheres encountered in mines, metallurgical works, chemical and other industries. As a result of these investigations, the Bureau issued a schedule5 of tests under which manufacturer who voluntarily submit masks for examination and test, are issued an approval certificate for masks that meet the Bureau's specifications. In the Bureau's schedule, masks arc classified by types of gases removed, as type A masks for protection against acid gases; B; organic vapor; C, ammonia; D, carbon monoxide; E, smoke, dust, and mist; F, special gases; combination types, and type N, for protection in air against all gases, vapors, and smokes. The purpose of this paper is to describe the physical and chemical tests that were conducted on a type N mask, the protective principles and construction of the essential elements of the canister and attachments, and the uses and limitations of this type of mask. The mask tested is known as the all-service mask, manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa;, and was approved (approval No. 1403) by the Bureau on July 1, 1924, for protection from all classes of poisonous vapors, gases and smokes in air.

Jan 1, 1925

By Warren W. Krech

Rock property data is needed over a wide range of parameters for the optimum execution of rapid excavation research. Eight rock types were chosen by the Bureau of Mines for a standard rock suite for such research. Large rock blocks were quarried and the standard physical and mechanical properties measured and documented. The eight rock types that comprise the rock suite are Barre Granite, Berea Sandstone, Dresser basalt, Holston Limestone, Salem Lime-stone, Sioux Quartzite, St. Cloud Gray Granodiorite, and Westerly Granite. Geologic, petrographic, physical-property, and mechanical-property test data are reported for each rock type. The information is the first step in the building of a comprehensive property listing for the eight rock types. A limited number of rock cubes are available from the Bureau of Mines Twin Cities Mining Research Center for use by researchers to broaden the information available on the suite.

Jan 1, 1974

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By E. L. Garton

The United Status Bureau of Mines has recently collected samples of crude petroleum from well] in the newly developed Joiner, Kilgore, and Longview fields of Rusk and Gregg Counties in the East Texas district, and from the Van field of the East Central district of Texas. East Texas Cruder The four samples of crude oil from the East Texas fields are all typical "intermediate base" crudes according to the classification given by Smith and Lane. 3 Sample 31,063 is from the discovery well in the Joiner field. This well came in on October 3, 1930, with an initial production of 400 barrels per day. Sample 31,062 was obtained from a well that was completed on February 1, 1931, with an initial production of 3,500 barrels per day. The 32 East Texas crudes are produced at an average depth of approximately 3,600 feet. which is the deepest Woodgine-sand production so far encountered in any of the Texas or Louisiana fields.

Jan 1, 1931

By Doris M. Hyde

The Bahama's petroleum-dominated minerals sector constricted again in 1985. The declines were mostly the result of a soft market demand for crude oil and petroleum products. In early 1984, it was a growing unprofitability that prompted Charter Oil Co. to cease using the 350,000-barrel-per-day Bahamas Oil Refining Co. facility that it jointly owns with Chevron Oil Bahamas Ltd. After midyear 1985, because of poor petroleum economics, Chevron announced it would close the refinery, leaving only a maintenance crew. In 1984, the refinery exported less than 26 million barrels of petroleum products. Chevron's throughput was reported as averaging about 8,000 barrels per day at the time of the announcement. The crude oil transshipment terminal also registered declining activity and financial losses in 1984 and 1985. Transshipments of petroleum in 1985 amounted to about 100,000 barrels per day, one-half as much as in 1982.

Jan 1, 1987

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By S. A. Matthes

This Bureau of Mines report describes a system for the dissolution of metal and mineral samples using a microwave heat source. Samples and an acid mixture are placed in sealed polycarbonate vessels. The vessel contents are heated using microwaves, digested for 2 min, and quickly cooled. After the solution is brought to a final volume, the vessel contents are heated an additional 2 min in the microwave oven. Using this method, a slag, a feldspar, and a Ni-Cu alloy were dissolved and analyzed by atomic absorption spectroscopy. Values obtained for Na, K, Cu, Ni, Si, Mg, Mn, Ca, Al, and Fe agreed with certified values and had an average relative standard deviation of 1 pct. This system results in a significant savings in time and expense over traditional methods of sample dissolution, and is ideal for preparing solutions for analysis by atomic absorption, plasma optical emission, or X-ray spectroscopy.

Jan 1, 1983

By Edward A. Mihok

Laboratory batch-flow tests conducted on a highly ferruginous acid mine water with an activated carbon showed that ferrous iron is rapidly oxidized. This indicates that air oxidation of ferruginous acid in mine waters is catalyzed by activated carbon. The ferrous iron content of an acid mine water flowing through an aspirated activated carbon column was reduced from about 700 to about 10 parts per million in less than 1 minute. Highly efficient ferrous iron oxidation was achieved by conditioning the activated carbon by repeated treatment with acid mine water and air. The reaction proceeds rapidly in the acid environment (pH about 2.5) engendered by ferrous iron oxidation. The activated carbon was used repeatedly with little loss in efficiency, no discoloration, or solids deposition. In these batch tests, about one-third of the iron was adsorbed by the carbon, but with continuous flow, little iron adsorption is expected. Incorporating a catalytic oxidation step in the treatment of acid mine waters containing ferrous iron would greatly facilitate neutralization--precise control of pH, lower reagent costs, elimination of aeration equipment, and smaller holding ponds.

Jan 1, 1969

By J. E. Pahlman

One of the goals of the Bureau of Mines is to develop metallurgical pro-cesses that conserve energy and/or that take advantage of abundant domestic energy sources. Western lignites and subbituminous coals can be used for firing pellet induration and metallization furnaces. However, the refractory linings of these furnaces must be able to withstand attack from corrosive alkali metal oxides present in the ash of many of the low-rank fossil fuels. The Bureau of Mines conducted dynamic and static slag tests on high-alumina and alumina-silica refractories to determine their resistance to lignite ash slags. The investigations showed that increased alkali content in the lignite ash caused increased corrosion and erosion of the tested refractories. The degree of corrosion decreased with increasing alumina content, with the 99-percent-alumina refractories having the highest resistance. In general, the matrix phase was attacked preferentially to the alumina grains. Also, porosity reduction and tar impregnation enhanced the corrosion and erosion resistance. The 90-to 99-percent-alumina refractories are recommended for use as furnace linings in alkali slag environments.

Jan 1, 1979

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

By George S. Rice

"Soon after the armistice, an investigation was conducted by the writer on the use of liquid oxygen for explosive purposes in Germany, so far as the conditions of such investigation wore permitted at the time. The results of this inquiry were published in Technical Paper 243, entitled ""Development of Liquid Oxygen Explosives during the War.""Recently, through the courtesy of Dr. C. L. Parsons, former chief chemist of the Bureau, who was visiting Germany, and Mr. Chester L. Benson, of the American Expeditionary Forces in Germany, data was obtained from the Deutsche Oxhydric A. G., Surth near Cologne, (one of the principal manufacturers of liquid oxygen installation) concerning the number of plants which bad been installed in Germany during the period following the armistice. An analysis of the figures obtained shows the following installations in different kinds of mining operations:"

Sep 1, 1920

By Michael A. Evanto, George J. Karabin

The Mine Safety and Health Administration, Pittsburgh Safety and Health Technology Center, Roof Control Division, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions is essential to ensuring a safe working environment for mine workers at a given site. Since 1985, the Roof Control Division has successfully used the boundary-element method of numerical modeling to aid in the resolution of complex ground control problems. This paper presents an overview of the modeling methodology and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the United States is included, and a set of deterioration indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy is introduced. Finally, a case study is detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 5, 1999

By Helen W. Lang

The Bureau of Mines has developed a very rapid gas chromatographic method for routine determination of oxygen, nitrogen, methane, and carbon dioxide in mine atmosphere samples. Analysis is accomplished in 3 min; readout appears on a single strip chart. The gas sample is split between two columns contained in separate chromatographs. A 5 A molecular sieve column separates oxygen, nitrogen, and methane; a porous polymer column separates carbon dioxide from an air peak. Direct selective analysis of methane from this unresolved air peak is accomplished using a hydrogen flame ionization detector (FID). Carbon dioxide is catalytically converted to methane and detected by FID.

Jan 1, 1972

By J. M. Oestreich

Supercritical water (sew) Is being tested for commercial use 1n several organic extraction systems but little work has been done on the extraction of metals from minerals. This lack of information prompted Bureau of Hines (BOM) research into the sew treatment of minerals. As a result, this research project is intended to serve mainly as a starting point for further experimentation. A simple flow-through reactor was built out of high pressure tubing and used to treat minerals with SCU at 400? C and 3500 to 7000 psi. The research produced four main conclusions: (1) carbonates of copper, iron, and lead convert to oxides; (2) most iron minerals showed alteration to oxides with some iron dissolution; (3) valuable trace elements including nickel, chromium, and others leached to some extent from sea minerals along with some calcium, iron, silicon, and sulfur; and (4) treatment of sulfides extracted elemental sulfur and resulted in several alteration reactions, though with the exception of cinnabar and the iron bearing minerals, the metals in sulfides were mainly insoluble. Surface alterations on many of the minerals show significant changes have occurred in the minerals even when only minor extractions were detected. These surface effects may be very important when used in conjunction with flotation processes since the sew treatment may selectively enhance or suppress a mineral's floatability.

Jan 1, 1989

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

By W. C. Holliman

This report describes apparatus and procedure used for determining the vapor pressure of aviation gasoline in surveys of commercial aviation-gasoline characteristics made by the Bureau of Mines in cooperation with the Coordinating Fuel and Equipment Committee of the Coordinating Research Council, Inc. (CFR-CRC). The method is a modification of the Reid method, in which a mercury manor is substituted for the Bourdon-type gage of the Reid method. The method was used in earlier surveys made by the National Bureau of Standards in cooperation with the CFR-CRC, and was used in the Bureau of Mines surveys at the request of the cooperating organizations. It is designed for special research problems? particularly in vapor-lock studies, which require a precision greater than obtainable by the Reid vapor pressure method. A repeatability of + 0.01 p.s.i. average deviation from the mean may be obtained by method.

Jan 1, 1950