Search Documents

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By J. H. Jansky, P. W. Jeran, G. L. Hassett, M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emissionin 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States had daily methane emissions of 1 MMcfd or more, These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va,, which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.5 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1975

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By G. T. Lineberry, W. J. Wiehagen

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: (I) job definition through task analyses; (2) the ranking of job elements by perceived cost consequence; (3) observational techniques to establish performance baselines; and (4) cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technologic efforts but include consideration of the so-called "soft-skill technologies" aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

By Andrew Cecala

During a recent National Institute for Occupational Safety and Health field evaluation of a newly designed filtration and pressurization system for an enclosed cab of a surface drill, it was determined that the drill operator's respirable-dust exposure was significantly increased during time periods when the cab door was opened to manually guide another section of drill steel into place to achieve additional cutting depth. Although no dust cloud was visible when the door was opened to perform this task, the drill operator's exposure was documented (over a three-day test period) to be nine times higher than when the cab door was closed. Even at this higher respirable-dust concentration, the drill operator's exposure remained well below the permissible exposure limit governed by the federal dust standard; however, an alternative method is being investigated to guide the drill steel in place in order to eliminate this increased exposure. .

Jan 1, 2008

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

By Suzann C. Ambrosio

Crude petroleum, the only commercially exploited mineral resource in Cameroon, continued to dominate developments in the mineral industry sector. International mining concerns have expressed interest in developing Cameroon's bauxite and iron and steel potentials. Domestically, the mineral industry focused on production of fertilisers for agricultural development, infrastructure construction, and hydrocarbon development, through the nearly self-sufficient production of fertilizer materials, cement, and crude oil. The mineral sector contributed 5.6% to the estimated 1981 gross domestic product (GDP) of $6.5 billion.2 Petroleum exports accounted for approximately 4.5% of the 1981 GDP and exceeded coffee and cocoa exports for the second consecutive year. The trade gap widened during the fiscal year ending on July 80, 1981, owing to a 21% increase in exports and a 25% increase in imports. Offsetting these balance-of-payments difficulties, typical of developing countries' early economic stages, were increases in foreign exchange reserves to $71 trillion by May 1983.

Jan 1, 1983

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By Richard A. Thomas, Charles D. Litton, Kenneth E. Mura, Harry C. Verakis

Experiments were undertaken to evaluate the flammability of typical noise abatement materials used to line the cab interior of mobile mining equipment. The experiments were conducted using three different experimental configurations: 1. A ventilated tunnel test. 2. A full-size cab test where the interior surfaces were lined with the sample material and then ignited near the floor using a methane-air burner. 3. Standard ASTM E-162 tests using a radiant panel test apparatus. This paper describes the tests and presents the results obtained for 15 to 20 different materials of various chemical compositions and thickness. With one exception, materials that did not exhibit flame spread in the tunnel test also performed well in the full-scale cab test. All materials that had passed only a small-scale flammability test, such as SAE J369, failed dramatically in all three of the above test configurations. With one exception, all materials that performed well in the full-scale cab test had flame spread indices < 25, based upon the ASTM E-162 results. The lone exception had an ASTM E-162 flame spread index of 68. With regard to samples that failed the full-scale cab test, the carbon monoxide levels within the cab reached lethal concentrations in the range of 1.8% to 3.8% within 2 minutes from ignition of the sample—dramatically illustrating the severe fire environment that can result within the cab space.

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User&apos;s guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District&apos;" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments&apos; characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner&apos;s breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult&apos;s law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987