Search Documents

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By E. Chin

Natural gas was the only economically significant mineral produced. A significant amount of the gas output was consumed in the production of nitrogen fertilizer and electric power. Proved reserves of natural gas were abundant and at least sufficient to supply most of the country's industrial and domestic needs for many decades to come. Other mineral production was of little importance to the Bangladesh economy, although there were prospects for developing some of the nonmetallic minerals. The flat river-delta terrain comprising nearly all of Bangladesh made the potential for discovering major, economically exploitable mineral deposits poor. The deep sediments, however, have good potential for crude oil or additional natural gas discoveries.

Jan 1, 1985

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974

By Phyllis Lyday

Mining did not contribute significantly to the economy of Benin, a small country on the coast of West Africa, during 1978-79. During these years, Benin continued to be rated by the United Nations as one of the 25 least developed countries in the world; its gross domestic product was under $200 3 per person per year. Salt from seawater, sand and gravel, bricks, and imported clinker for cement were the only minerals which contributed to the economy. Minerals were not expected to play an important role in the commercial sector of Benin's economy during the next decade. Joint projects included infrastructure development to create a coordinated road and rail system between Niger and Benin that was begun in 1960 as ?Operation Hirondelle." In 1976, an agreement for the construction of a rail link from Niamey, Niger, to Parakou was signed. At Parakou, the rail line would join the existing line to the port at Cotonou. Construction of the rail line was expected to take 6 years, and the cost was estimated at $287 million in 1979. During late 1979, the Federal Republic of Germany granted Benin a loan of $12 million for reconstruction of the port at Porto Novo. Benin and Nigeria were discussing a joint adventure in crude salt exploitation.

Jan 1, 1981

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By James L. Elder

Field-scale experiments were conducted at Gorgas, Ala., from 1951 to 1954. Three reaction paths were formed by electrolinking-carbonization, using electrode spacings of 150, 152, and 155 feet. The coal along these reaction paths was gasified, using air, oxygen, and steam separately or in various combinations. At the conclusion of operation, a drilling survey was conducted to determine the location and approximate area of the reaction zones. During the applications of the electrolinking-carbonization technique the maximum limitation on electrode spacing was not determined. Initial tests were conducted at 60-foot spacing. Successful path-preparation tests were made at 150-, 152-, and 155-foot spacings, and the indications were that much longer spacings were possible. The potential requirements appear to be constant, regardless of path length, while the gross power required probably will increase with path length. During the carbonization phase gas was produced that is similar in quality to coke-oven gas produced at low to intermediate temperatures.

Jan 1, 1957

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By Gerald J. Joy, Paul J. Middendorf

This study examines the patterns and trends in noise exposure documented in data collected by Mine Safety and Health Administration inspectors at U.S. coal mines from 1987 through 2004. During this period, MSHA issued a new regulation on occupational noise exposure that changed the regulatory requirements and enforcement policies. The data were examined to identify potential impacts from these changes. The overall annual median noise dose declined 67% for surface coal mining and 24% for underground coal mining, and the reduction in each group accelerated after promulgation of the new noise rule. However, not all mining occupations experienced a decrease. The exposure reduction was accompanied by an increase of shift length as represented by dosimeter sample duration. For coal miners exposed above the permissible exposure level, use of hearing protection devices increased from 61% to 89% during this period. Participation of miners exposed at or above the action level in hearing conservation programs rapidly reached 86% following the effective date of the noise rule. Based on inspection data, the occupational noise regulation appears to be having a strong positive impact on hearing conservation by reducing exposures and increasing the use of hearing protection devices and medical surveillance. However the increase in shift duration and resulting reduction in recovery time may mitigate the gains somewhat.

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974