Search Documents

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By Murray Jacobson

A method for determining airborne trona dust concentrations using a midget impinger was developed. During sampling, the trona dust, composed of sodium carbonate and bicarbonate, dissolves in the collecting medium (water). Resulting solutions are then titrated using 0.1 [N] hydrochloric acid solution. The mass concentration of the trona sample is determined from a calibration curve relating the volume of acid required for neutralizing a collected sample to the mass of the dust. Test results obtained using this method are equivalent to those obtained using a gravimetric sampling method.

Jan 1, 1971

By L. A. Haas

In this Bureau of Mines investigation, conditions were determined to form an iron sulfide adherent coating with a metallic golden luster on steel upon anaerobic heat treatment with sulfur. The sulfide formation rate was determined in the temperature range of 105° to 500° C with reaction times up to 68 hours. The optimum temperature and time to form an adhering decorative coating on mild steel was in the range of 105° C for about 70 hours to 285° C for 1 hour. The golden coating consisted of an inner layer of pyrrhotite and an outer layer of pyrite. At temperatures higher than about 300° C, the outer layer thickness decreased owing to the decomposition of pyrite to pyrrhotite.. Small quantities (<0.5 wt-pct) of petroleum oil accelerated the sulfide growth rate. The sulfide coating decreased the corrosion rate of steel in a neutral aqueous medium by a factor of two. The dissolution of pyrite in water was dependent on particle size and surface area with the flat pyrite coatings exhibiting the lowest dissolution rate.

Jan 1, 1974

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an&apos; type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By Chas F. Jackson

 The annual reports of the supervising engineers of the several sections of the Mining Division are assembled herein and comprise the annual report of the division. During the year under review the work was oriented entirely to the war program by applying apparatus and technique previously developed in research directly to war problems, as well as by intensified search for and exploration of deposits of minerals necessary in the war.

Oct 1, 1942

By George S. Rice

The following paper was presented at an International Conference on Mine Safety Research held at Dortmund, Germany, September 23-28, 1935, inclusive. This conference was attended by representatives of Belgium, France, Germany, Great Britain, and the United States ands by invitation, Czechoslovakia, Poland, Spain, and Russia. The first international conference of representatives of mine-safety, research stations was held the United States Bureau of Mines Pittsburgh Experiment station in 1912 .4/

Jan 1, 1936

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA&apos;s staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By L. A. Morely

Volume II of the final report concerns the application of sensitive ground-fault interrupters (GFIs) to ac utilization circuits in U.S. mines The main concepts examined are shock prevention and methods for reducing nuisance tripping. The research involved a literature search, input from previous Bureau of Mines contracts, and contacts with electrical manufac-turers and mining personnel. Following this background work, several devices that showed promise were obtained and tested. Results of testing indicate the existence of GFIs that may be modified to perform adequately on U.S. mining systems. A recommended set of guidelines is included in the report, covering design, construction specifications, and performance tests.

Jan 1, 1982

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By Paul S. Goodman

Volume I This report presents the first national survey of miners&apos; attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners&apos; attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By R. O. Pynnonen

This publication presents a study by the Federal Bureau of Mines of 494 accidents in open-pit iron-ore mines, beneficiation plants, and shops of the Lake Superior district from March 1949 to June 1956. These accidents caused 499 lost-time injuries, including 12 fatalities. A similar Bureau publication, Information Circular 7744, Analysis of 346 Accidents, Underground Iron-Ore Mines, Lake Superior District, was published in April 1956. Accident reports were analyzed by the Bureau to show the causes of in-juries and the unsafe practices or conditions that caused the accidents. Also shown are the time charges, times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 27 percent of the total number of disabling accidents that occurred in open-pit iron-ore mines, beneficiation plants, and shops in the district during the period covered. The text also contains tabulations of the accident experience and graphs with straight-line injury-frequency, injury-severity, and fatality trends for the period 1946-57.

Jan 1, 1959