Search Documents

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Lon A. Williams

This appendix contains drawing lists and drawings of components and assemblies designed for the prototype portable and machine mounted lighting systems per Tasks II & IV of Contract No. H0220065.

Jan 1, 1976

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By R. B. Tippin

Research investigations conducted on five ore samples show the applicability of heavy liquid separation (HLS) techniques to mineral processing. Under proper operating conditions, semicontinuous tests in small fluid cyclones yielded 90 percent sink-float concentrates with recoveries exceeding 90 percent on minus 35-mesh ore samples of kyanite, potash, spodumene, fluorspar, and beryl. Although none of the ores were examined in detail, their response to this novel concentration method provides basic examples that are typical of the process. Various aspects of cyclone design and operational characteristics of heavy liquid cyclone circuits were studied which demonstrated the flexibility of HLS by using multiple units connected in series. A comparison of two heavy liquid solutions, tetrabromoethane and methylene bromide, exhibited their individual advantages and limitations. Unique problems relative to this process are discussed including liquid viscosity, mineral composition of the ore, toxicity, and material handling hazards.

Jan 1, 1968

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

To develop a cost-effective tool for improving the performance of rock drilling systems used in detecting and delineating underground mine voids and for coal exploration. Approach To investigate admixtures of polyethylene oxide (PEO) at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life in rock drilling systems. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the surface of the rock being drilled. Laboratory drilling studies have been performed on rock types such as quart¬zite, granite, taconite, and marble. The lab tests were conducted using 5/8-inch diameter diamond-impregnated coring bits with cationic compounds as the surface charge neutralizing additives. These studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition.

Jan 1, 1991

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By Russel Bohn

The purpose of this study was to evaluate the various techniques far mine roadway dust control. This evaluation included (a) the types of dust suppressants available, (b) the interaction of these products with the properties of the roadway surface, and (c) the costs and performance measures of the predominantly used dust suppressants. Over 30 products were identified having a wide range of effectiveness depending largely on the properties of the road base, subsurface, and wearing surface. The effectiveness of a dust suppressant was also found to depend on the application and maintenance procedures employed. As a result of this investigation five dust suppressants were identified s being predominant in the surface mining industry: Coherex, wetting agents, lignin sulfonate, water, and calcium chloride: An approximate cost-effectiveness analysis, limited by the lack of quantitative field performance data, showed that the five suppressants ranked in the order given above, with water being one of the least cost effective. This report also presents an analysis of applicable federal and state regulations.

Jan 1, 1981

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973