Search Documents

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

By R. S. Olsen

The Bureau of Mines is engaged in a continuing research effort toward the recovery of alumina from kaolinitic clay and other nonbauxitic domestic minerals. Hydrochloric acid extraction of calcined clay is among the acid processes under consideration. Although aluminum is easily leached from calcined clay, the presence of fines and slimes in the leached residue has hindered the application of this and other acid leaching processes. A clay feed preparation method was therefore developed that eliminated the slimy nature and the separation problems normally associated with leached clay residues. The preparation process consists of crushing the raw clay to minus 20 mesh, dampening the crushed clay with a fine water mist while tumbling on a rotating disk, and calcining the misted clay at 750° C. The misting process increases residue settling rates threefold to 9 cm/min (18 ft/hr) and filtration rates by two orders of magnitude. Leaching-kinetics were determined for misted clay feeds in a batch, stirred-tank reactor. Rapid leaching occurred during the first 85 to 90 pct of the extraction. The linear relationship of extraction to time during this initial phase corresponded to a zero order reaction with a rate constant of around 10 pct/min.

Jan 1, 1981

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By G. Nuñez, M. A. Pathak, A. A. Afshari, C. F. Stanley

"To help evaluate the vibration patterns of an excised lung, a method is developed to determine which parts of the surface of an excised lung are responding to acoustic excitation via the trachea. Holographic interferometry, a very' sensitive technique ·that can measure movements of a few microns, is used to detect the lung surface movements.The intact lung and heart are excised from Long· Evans male rats weighing 250 gm. A tube is inserted into the trachea and connected via a funnel to a 3 inch cone speaker. The assembly is positioned in the holographic unit and excited at frequencies up to 10,000 Hz. The holographic unit contains an acousto-optic shutter used with a 0.5 watt Argon laser.The resulting reconstructed holograms contain interference fringes that are indicated of lung surface vibration.INTRODUCTIONA 1986 report by the U.S. National Committee on Biomechanics [1] describes diseases of the lung as a major national health problem. One of the recommendations of the report is for continued study of the mechanical properties of lung tissue. As an example, the report cites at least three areas that would benefit from a better understanding of the vibratory patterns or the lung."

Jan 1, 1989

By Gopala N. Krishnan

The most promising candidate for the recovery of alumina from non-bauxitic sources is the leaching of clay by HCL acid followed by crystallization of aluminum chloride hexahydrate (ACH) by hydrogen chloride sparging. Hydrothermal precipitation of boehmite ( ?-A100H) from aluminum chloride solution will simplify the process, will reduce energy consumption and will eliminate corrosion problems involved in calcination of ACH to obtain alumina. This report summarizes the results of Phase I of a program to study the precipitation of boehmite from AlC13 solutions. The amount of boehmite precipitation from dilute A1C13 solutions (5 wt%) is . negligible below 200°C. Above 200°C the precipitation increases with increasing temperature approaching 40% at 300°C. Addition of HCl acid to the dilute A1C13 solution even in small quantities drastically reduces boehmite precipitation. Solution impurities such as Fe, Ca, Mg, or Na substantially promote the precipitation of boehmite. No precipitation is observed from concentrated A1C13 solution (30wt%) representing the leach liquor.

Jan 1, 1980

By Thomas V. Falkie, R. Venkataramani

Proposing A Model In this investigation, a model of the form: n Y = a0 + E a x. A-1 v=l J J was postulated, where the number of independent variables "n" was originally fifteen. The following experimental hypothesis was to be tested: Null Hypothesis: the coefficients a = 0 J Alternate Hypothesis: One or more of the coefficients a 0 J Correlation and Regression To establish the alternate hypothesis and to test how well the proposed model fits the data, the conventional statistical techniques of correlation analysis and multiple linear regression analysis were used. Additionally, factor analysis was employed to investigate the dependency relationships in the data. Correlation and linear regression are well established statistical procedures in science and engineering. References on these procedures include Spiegel (1961), Anderson (1963), and Draper and Smith (1966). A simple example is stated here. If N observations are made of two variables, x and y, and it is desired to test this data to see if a linear relationship exists, then a model of the form: Y = a0 + a 1 x A-2 is proposed. The values of a0 and al may be calculated from the raw data by the "least square normal equations", which are:

Jan 1, 1972

By G. W. Eiger

Bureau of Mines laboratory tests show that ilmenite concentrates with titanium dioxide contents as low as 33 wt--pct can be beneficiated to produce a crystalline substitute for natural rutile suitable for direct chlorination. The synthesized product prepared by a three-step procedure was comparable with natural rutile in titanium content. Reduction smelting of ilmenite removes iron as a pig iron byproduct, and the remaining slag phase is greatly enriched in titanium. Oxidation of the slag in the presence of phosphorus¬bearing slag additive converts the titanium-bearing phases to discrete rutile crystals and a glass phase containing most of the associated impurities. Rutile is separated from the glassy impurities by attrition scrubbing ground slag in dilute phosphoric or sulfuric acid solutions. Tests made in a laboratory fluid-bed reactor show that synthetic rutile responds to chlorination at the same rate as natural rutile and that more than 95 pct of the titanium contained in the feedstock was extracted as titanium tetrachloride.

Jan 1, 1974

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By Ivette E. Torres

The estimated value of world crude mineral production in 1992 was $1,633.3 billion in terms of current (1992) dollars, or $1,178.0 billion in terms of constant 1983 dollars. This latter figure was 4.8% above the 1992 level but was 2.4% below the record-high level of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. The statistical base for this estimation is derived from the data on the value of production of a group of key commodities that was published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983. The aforementioned values and those presented in the table are for crude minerals only and only begin to suggest the impact that the mineral industry has on the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the Earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of processed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,800 billion constant 1983 dollars or $3,900 billion in terms of 1992 dollars.

Jan 1, 1994

By John E. Miller

A high accuracy Burnett apparatus for use at 12,000 psi and 0° to 65° C has been constructed at the Bureau of Mines Helium Research Center. The apparatus is patterned after Burnett's original apparatus, but the working pressure is much higher and elastic distortion can be essentially eliminated. An operating procedure to permit faster experimental measurements is suggested.

Jan 1, 1967

By William B. Harper

Domestic sales of carbon black sustained the upward movement for the 4th consecutive year, reflecting the increased sales of motor vehicles during the same period. Sales of carbon black in the domestic market topped 2 billion pounds for the first time during 1965 and have more than doubled the output of 20 years earlier. By far the largest user of carbon black is the rubber industry. That use accounted for more than 94 percent of the carbon black consumption with the bulk of it being used in tire casings and tubes. Thus demand for carbon black is naturally sensitive to trends in the sales of passenger cars and other motor vehicles, Manufacturers of inks, paints, plastics, paper chemicals, and food are also important users of carbon black.

Jan 1, 1967

By Peter G. Kovalchik, Lawrence W. Scott, Thomas H. Dubaniewicz, Frank T. Duda

Overheating of electric cables on shuttle cars has long been recognized as a cause of premature insulation failure leading to shock and electrocution. Use of cable reels on shuttle cars can cause excessive heat build up which, in turn, causes the cable insulation to soften and become easily damaged This heat-softened insulation reduces the life of the cable. Repeated cycling of a cable in this manner can cause premature aging of the insulation; it becomes bridle, cracks and allows electrical leakage paths to farm. These leakage paths provide the opportunity for shock and electrocution to occur if miners come in contact with the damaged section of cable. It is imperative that cable operating temperatures be maintained at safe thermal limits. This paper discusses a research project conducted by the National Institute for Occupational Safety and Health, Pittsburgh Research Center to determine dynamically the conductor temperature of reeled shuttle car cables using fiber optics technology. The research portrays typical shuttle car loading cycles (both current and time cycles). Root-mean-square current loading is calculated based on the results. The thrust of this effort is to provide the scientific basis for ampacity derating factors specifically for mine machinery using reeled cables This information will reduce the probability of electrical hazards from reeled cables

By S. H. Katz

"At the annual meeting of the International Association of Fire Engineers at Kansas City, Mo., in June, 1919, the Bureau of Mines offered to cooperate with municipal fire departments for the purpose of obtaining information regarding composition of the air in burning buildings. (Katz, S. H., Statement made at Convention of International Assoc. of Fire Engineers: Fire and Water Eng., vol. 66, July 16, 1919, pp. 129-30, also Fireman's Herald, vol. 78, July 12, 1919, pp. 48.) The gas-mask laboratory of the Bureau's experiment station at Pittsburgh sent vacuum bottles for taking samples to fire chiefs in twenty-five cities, who had signified their intention to aid in this work. It was hoped to obtain one hundred or more samples, because statistics in quantity are necessary for drawing reliable conclusions concern-in the likelihoods of encountering irrespirable as in burning buildings. This far, eleven samples have been received by the laboratory. Results of analyses and pertinent data regarding these samples are given in the accompanyingEight of the eleven samples contained, no carbon monoxide; seven of the eight were taken above the ground level and one below ground. One sample taken above ground contained 0.03 per cent carbon monoxide, and this quantity is not dangerous to breathe for a limited time. Of the three samples taken below ground, one contained no carbon monoxide; the other two contained 0.10 and, 0.35 per cent, respectively. This indicates that in a burning building, the hazard from carbon monoxide is much greater below the ground level. The cause undoubtedly lies in the poorer ventilation that is usually found in cellars or basements. Abundance of ventilation provides the necessary air for complete combustion, or if incomplete combustion does occur, the carbon monoxide generated by the fire is greatly diluted with fresh air and swept away by the current. It may be noted that the highest proportion of carbon monoxide was found in a cellar where a fire as burning among piled cases. The difficult access of air to the burning parts facilitated the formation and lib ration of carbon monoxide. The smoke here was very light and no difficulty was experienced in breathing. Some of the air containing dense smoke showed little change from normal air by analysis. Thus the density of smoke or the irritation and difficulty it causes in breathing are no indication of the presence of poisonous gas. None of the samples shows important oxygen."

Nov 1, 1920

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS.

Jan 1, 1977

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

Measure the daily exposure of individual miners to alpha particles emitted by radon daughters (radioactive decay products of the radon gas present in the mine atmosphere). Approach A dosimeter worn by a miner counts alpha particle emissions from radon daughters, RaA (Polonium 218) and RaC (Polonium 214), collected on a filter, and stores the gross count for later readout. How It Works A pump draws air into the detector assembly where radon daughters are collected on a filter. The detector, a solid state surface barrier type, is mounted in the filter head behind a thin mylar disc which serves as a moisture barrier. When a radon daughter decays and its alpha emission strikes the detector, the alpha particle causes a pulse of electrical charge in the detector. The circuits used to condition and count the electrical pulses generated in the detector are represented by the other blocks shown in the simplified block diagram. Each pulse is first amplified.

Jan 1, 1979

By Lloyd A. Morley

Two mine electrical power system simulations are presented. The first is a batch processed procedure capable of modeling a single mining machine consisting of a number of motors operating under various loads. These loads are the mechanical torque loads present at the motor shaft. The second simulation is a more flexible tool for modeling entire mine electrical power systems~ Detailed analyses of bus voltages, transmission-line power flows, and machine behavior are possible. This simulation operates interactively and the power system is configured as the user responds to program generated questions and requests. Development of the theory behind the programming, as well as detailed explanations of the models, is presented. Examples are provided to demonstrate simulation capabilities.

Jan 1, 1978