Search Documents

By T. Brady, R. Langston, J. C. Johnson, H. Kirsten

An experiment is described in which instrumented rock bolts were used to measure strain in the rock mass during drift development at the Stillwater Mine, Nye, Montana, USA. Two strain-gauged rock bolts were grouted into the middle of the rib next to the face. The drift was excavated in three advances, each one-half drift wide. Strains were recorded hourly by a data logger. Results show that the average change in axial bolt strain for the first and second advance was about the same and that there was almost no change in strain after the third advance. Bending strain was observed 19 cm from the head of the bolt.

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

By X. Shi, V. Vallyathan, N. S. Dalai

"Electron spin resonance (ESR) measurements show that grinding of quartz particles in air produces silicon-based (Si- and SiO-) radicals which decay with aging in air. ESR spin trapping measurements provide evidence for the generation of hydroxyl and possibly superoxide radicals from a suspension of fresh quartz particles. The hydroxyl radical generation potential of the fresh quartz particles decreases on storing in ambient air and on the addition of catalase, superoxide dismutase, desferoxamine, or DMSO. Silica-induced lipid peroxidation also decreases on storing the fresh particles in ambient air. These findings suggest that oxygenated radicals play a role in the biochemical mechanism of pneumoconiosis in general and acute silicosis in particular.INTRODUCTIONThis communication summarizes our electron spin resonance (ESR) investigation of the formation of oxygenated radicals by freshly crushed quartz particles in a cell-free aqueous medium, and its potential role in the biochemical mechanism of acute silicosis. This study was undertaken because the mechanisms by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood. 1-3 It is generally believed, however, that the action of quartz particles on the cell membrane is the starting point of the silicotic process. 1,4 Since the first step must involve surface reactions, characterization of the chemical structure of the surface of quartz particles has been the subject of several recent studies!-' For example, we reported that mechanical crushing of quartz under normal atmosphere generates silicon-based (Si• and SiO•) radicals which decay with time, and that these radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to that of an aged dust from the same stock. 6,8 Independently Fubini and coworkers' have also reported on the formation of Si• and SiO• -type of radicals from quartz particles crushed under atmospheric conditions. Gulumian and van Wyk9 have reported that quartz particles react with hydrogen peroxide (H202) to generate hydroxyl (•OH) radicals. These authors9 suggested that this process might contribute to quartz's pathogenicity but the mechanism of the -OH radical formation was not clarified. Earlier, Gabor and Anca10 had suggested that the cytotoxicity of quartz particles might be associated with the generation of some factor or factors possessing the properties of a free radical and hence capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently, Weitzman and Graceffa 11 reported that asbestos is able to catalyze the generation of -OH radicals from H2O2. Their later work12 indicated that lipid peroxidation might be one of the mechanisms of tissue injury by asbestos."

Jan 1, 1989

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

SUMMARY The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactc rely demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No. 1 Mine in Grant Town, West Virginia. The remote sealing consists of: (1) A sonar initial probing system which can operate satisfactorily even in the presence of dense smoke. The system is capable of determining both the local passageway geometry, identifying the presence of cribs and other obstructions, and the position of the borehole in the mine passage. (2) A mine sealing material system which utilizes fly ash for making the complete seal or as a bulk filler in conjunction with a urethane, froth foam, seal topping system. The choice of using fly ash alone or fly ash with foam topping depends on a number of factors, such as quality of seal desired, time available per seal, depth of borehole, passageway geometry, and water holding require¬ment. The fly ash-foam seal is a better seal, capable of sealing against a higher water head than fly ash alone. The fly ash sealing

Jan 1, 1973

This report, which updates and supersedes the Office of Surface Mining's 10-year progress report published in 1987, deals with the accomplishments of the regulatory and abandoned mine land reclamation programs during the first 15 years of the Surface Mining Control and Reclamation Act of 1977 (SMCRA). Part 1 is an illustrated description of on-the-ground accomplishments; Part 2 presents statistical information for the 15-year period. The data in this statistical report are organized in two sections: national statistics and state statistics. The national statistics provide an overview of coal mining and the implementation of SMCRA since 1977. The information reported for the states presents a brief description of the coal reserves in each area, accompanied by detailed statistics and graphs that relate each state to the nation as a whole. The statistics compiled in this report are from the Office of Surface Mining's files, computer data systems, and annual reports. During the early years of the program, many of the data categories were evolving and changing; therefore, data reported over the 15-year period are not complete for all states for all years, and where data was unavailable or zero, a dash (-) is shown for that item. The data sources used to compile the tables and graphs are listed and described in detail on page 76. Due to the number of requests for this information in the past, statistical information about coal mining and its regulation will be available each year as an appendix to the Office of Surface Mining's Annual Report to Congress. Beginning in Fiscal Year 1993, this information will be compiled and published on an annual basis. For more information about this report, call or write the: Public Affairs Office Office of Surface Mining 1951 Constitution Ave., N. W. Washington, D.C. 20240 (202) 208-2553

Jan 1, 1992

By John B. Ivey

This is a geologic study of the U.S. Bureau of Mines Oil Shale Tract in the Piceance Creek Basin of Rio Blanco County, Colorado for the preparation of a set of detailed surface geologic maps, measurement and identification of joint attitudes and frequencies, and the classification and mapping of the soils of the area.

Jan 1, 1978

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953

By Almon F. Robertson

"INTRODUCTION AND SUMMARYThis is one of a series of reports describing investigations within the Missouri River Basin in Montana conducted by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of Interior and others concerned with the planning of power and other water developments in the basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data that are considered confidential.The field investigations for this report were made during the summer of 1949. Virtually all known metallic mineral deposits in the county and same nonmetallic (industrial) mineral deposits were investigated. Most of the mines and prospects have been inactive for many years. The old underground workings generally are only partly accessible; many are entirely inaccessible. Most of the mining claims were located many years ago, and a considerable number were patented. Many claims were abandoned; others were relocated. Nimes and ownerships often have changed. Because of such conditions, much of the information on most of the mines and prospects necessarily has been obtained from available Federal and State publications, private geologists' and engineers' reports, and from owners and local residents.Metal mining in Cascade County, Mont., has been confined mainly to the silver-lead-zinc deposits in the Montana (Neihart) and Barker districts in the southeastern part of the county. The Neihart district has yielded by far the greater part of the county's metal output. The mines generally have been operated intermittently, largely because of fluctuating or low silver and base metal prices."

Feb 1, 1951

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

Reduce longwall equipment transfer time between panels by utilizing a predriven recovery room, and thus eliminate the premove preparation associated with most equipment recovery methods. Background and Approach The recovery point for a retreating longwall is a predetermined position near the end of the panel where mining is terminated and equipment is disassembled and removed. However, to prepare for equipment removal at the recovery point, bolting and wire meshing arc required before the recovery point is reached. Usually, preparations for equipment recovery begin about 35 ft from the recovery point, significantly impeding the normal rate of advance of the longwall and, consequently, production. Recently, BethEnergy Mines, Inc., and the Bureau of Mines cooperated to evaluate the applicability of utilizing predriven recovery rooms to improve longwall equipment recovery. A predriven recovery room is an entry driven parallel to the longwall face at the end of the panel, having standard dimensions (for that particular mine) and supported with bolts, wire mesh, and supplemental support. The preparation of this entry is completed before it experiences mining-induced effects from the approaching longwall face. This enables the face to continue to mine at its normal rate of advance until the panel is completed. The supplemental support is required to control the loads imposed by the front abutment and is the most vital component of the recovery room.

Jan 1, 1989

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971