Search Documents

By T. H. Dubaniewicz, J. E. Chilton

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 1992

By David Ingram

The results from the sound level measurements, the dosimeter recordings and the time-activity studies on four different air-rotary rigs indicate a wide variation of operator noise exposure during hole development. These variations appear to be dependent on the cab design and the operator?s drilling behavior. Studies have documented that exposure to high sound levels for long periods of time can cause hearing loss. The results of this study help identify the loudest parts of the drilling cycle. Sound level measurements on the four rigs show that all the rigs generate sound levels that are 90 A-weighted decibels (dB(A)) and above within 6 feet around the rigs during drilling. It is easy to conclude that some type of noise protection, such as a cab, is needed to protect the operator from overexposure to noise for an eight-hour shift of uninterrupted drilling. However, even when rigs are outfitted with cabs, operators observed in this study are being exposed to sound levels above 90 dB(A) during some activities required to complete a drilling cycle. An evaluation and comparison of the four dosimeter recordings and time-activity studies during one drilling cycle may explain why variations in operator exposure occur. Table 1 summarizes the time-weighted average (TWA) and accumulated dose percentages for each of the four operators during the time needed to complete one typical hole cycle.

Jan 1, 2008

By Andrew B. Cecala

While various types of equipment are used in bulk material processing plants to control respirable dust, the equipment often doesn't adequately protect workers. One cost-effective way to supplement your existing dust control equipment is to install a whole-plant ventilation system. This article outlines research by the National Institute of Occupational Safety and Health (NIOSH) on using whole-plant ventilation in two mineral processing operations to reduce respirable dust levels. Information also covers how to design a ventilation system for any bulk material processing plant.

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By J. A. Holmes

As part of its investigation of methods of increasing the efficiency of fuel resources, the Bureau of Mines is continuing the study of the general problems involved in the economic use of fuels in gas pro- ducers that were carried on by the technologic branch of the United States Geological Survey. In the course of this study many inci- dental problems of prime importance have demanded consideration. Among them is the determination, under practically constant con- ditions, of the duration of gas-producer tests necessary to reduce the possible error to a minimum. A discussion of this proper length of test period forms the first part of this bulletin. An attempt to dispel some of the uncertainties that arise in an investigation or to account for some of the minor phenomena often necessitates a systematic and careful study of certain chemical, ther- modynamic, or physical laws, or a combination of these, which in turn may result in information or conclusions of great value. Fur- thermore, seemingly unimportant observations often prove to bear directly upon the design, construction, or manipulation of the machine under test. In attempts to improve the gas producer considerable attention has been given by manufacturers to such questions as fixing or isolating the combustible components of the tar, utilizing the waste heat of the producer for the generation of the steam required by the plant, apply- ing the suction principle to bituminous coal and other tarry fuels, and many allied subjects. Little study, apparently, has been given to the physical-chemical conditions most suitable to the formation of hydro- gen and of carbon monoxide, with a view to regulating the percentages of these gases in generators using fuels other than anthracite coal or charcoal. An attempt was made to introduce such investigations when the operations of the government coal-testing plant began at the Louisi- ana Purchase Exposition in St. Louis in 1904, but owing to adverse conditions these problems were abandoned until the plant was trans- ferred to Norfolk in 1907. The delay in beginning this line of inves- tigations, together with the short testing season at Norfolk, limit the second part of this report to preliminary physical-chemical studies, which, however, were sufficiently significant to warrant careful ex- amination pending more complete researches, which are being carried on at the station located in Pittsburg.

Jan 1, 1911

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

By R. E. Thill

The ultrasonic pulse measurement system described measures velocities of longitudinal (compressional) and shear waves in rock to give values that can be used with density values to determine the dynamic elastic constants of rock. A special feature of this pulse measurement system is its unique acoustical bench that minimizes errors in pulse transit times that are commonly associated with coupling, sample alinement, and sample orientation. Some special features of the acoustical bench are its highly versatile transducer cartridges, a pneumatic ram coupling device, an orientation mechanism, and a vacuum chuck sample holder. The lathe-bed-like construction of the acoustical bench assures automatic alinement of samples and versatility in accommodating samples of various shapes and sizes.

Jan 1, 1968

By J. E. Wilson, J. D. Davis, C. R. Holmes

 The Bureau of Mines-American Gas Association (BM-AGA) method5/ has been used in surveying the carbonizing properties of American coals and, to date, in testing coals from 43 beds. The results in this report apply only to tests in the 18-inch retort at 800°, 900°, and 1,000° C. on coals from 32 beds. Table 1 gives the proximate and ultimate analyses of these coals and the name and location of mines. Coals from Pennsylvania, Virginia, West Virginia, Kentucky, Indiana, and Washington are considered. Seven of the coals are of low-volatile, four of medium-volatile, and twenty-one of high-volatile bituminous rank. One of the high-volatile coals (No. 45) is of high-volatile C rank, whereas all the others are of high-volatile A rank.

Mar 1, 1943

By W. A. Cole

This report covers the preliminary phase of an investigation of clays, shales, and certain rocks in Wisconsin to determine the feasibility of processing lightweight aggregate in the State. The study was extended to include rotary-kiln testing of a limited number of shale samples, and to an appraisal of the Maquoketa shale resources in eastern Wisconsin. A total of 45 samples of clays, shales, and other argillaceous rocks of Wisconsin were tested. The lower Maquoketa shale is the only material found to date that offers possibilities as a source of material that can be processed in a rotary kiln for lightweight aggregate. Bedrock occurrences of the Maquoketa shale are found in the eastern and southwestern parts of the State. The populous southeastern region of Wisconsin presents a large potential marketing area for lightweight aggregate. For this reason special study was directed to the Maquoketa shale in the eastern district.

Jan 1, 1961

By J. H. Field

Results of studies by the Federal Bureau of Mines on a pilot-plant scale for removing hydrogen sulfide and carbonyl sulfide from gas mixtures by the hot carbonate system are given in this publication. Gases containing up to 10 pet. hydrogen sulfide and 48 grains carbonyl sulfide per 100 cu.ft. were treated. In most tests carbon dioxide also was present and was removed simultaneously with the sulfur compounds. Because the rate of absorption of hydrogen sulfide is much more rapid than that of carbon dioxide over a wide temperature range, selective removal of hydrogen sulfide occurred in the bottom section of the absorber near the point of gas entry. Hydrogen sulfide was removed to pipeline specifications with carbonate solutions by using split-stream flows in the absorber and regenerator.

Jan 1, 1960

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By Ivan F. Avery

PRODUCTION of carbon black decreased 4 percent in 1961. Output in the major producing States of Texas and Louisiana decreased 1 percent and 8 percent, respectively. Production of channel black continued downward, declining 10 percent in 1961 compared with 9 percent in 1960. Furnace black production also decreased 3 percent from 1960. Total domestic sales, however, increased 2 percent, Sales to most major consumers increased, but sales to the ink industry decreased 10 percent. Producer's stocks decreased 5,083,000 pounds during the year. Exports decreased 4 percent. SCOPE OF REPORT Carbon black is a very pure grade of quasi-graphitic carbon; particle diameters range from 50 to 5,000 angstrom units. Annual reports were submitted to the Bureau of Mines by operators of all commercial plants in the United States.

Jan 1, 1962

By J. Koster

[In lQ jG thc E'lcct,ro:~(: L7.l :~u..-ic:ll S;%cti ?n of t?c :I. tcIl~tr,-;lcal 3:vi cioa, ?U~CE~U of lv!irtos, bc,~m an 9.ct iv.t In-:?*t ik7;5i GI of r.:ct.l-;c?;is for rccovcrin,; niclrel, cop?ir, an2 ?? cciou:; ~ot-1 c 1;-on or; :; of tile 3unl~crvi~.l~~ tiistrict in C1ni.k Coult:r, !Icl.r. ]

Jan 1, 1939

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

Aid mine workers in detecting hazardous roof conditions in underground mines by developing a method of roof sounding which supplements or replaces the traditional roof sounding technique where the miner relies on experience to determine whether or not the rock is sound. Approach The Bureau of Mines developed an electronic roof sounding de-vice that acoustically determines the integrity of mine roof rock by "listening" to the variation in frequency vibrations within the rock. How It Works n previous research, the Bureau of Mines found that loose rock in a mine, when impacted, vibrates at a much lower frequency and for a lower time period than does a solid slab. By quantifying the enhancement of low frequency vibrations in loose rock over solid rock, a repeatable, objective measure of the rock's soundness can be obtained. This approach was used in developing the rock stability tester.

Jan 1, 1986

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C.5 Safety Equipment and Control Devices Safety equipment and control devices serve two principal functions in mine escape hoists. First, they can be used to provide important safety features such as protection against overspeed, over¬travel and undertravel. Second they can be used to automate or partially automate the operation of the escape hoist. Typical equipment available is described in the following section. 1. Simplex and Lilly Hoist Controllers Manufacturers: Logan Actuator Co. 4956 No. Elston Ave. Chicago, Illinois 60630 312-736-7500 The Simplex and Lilly Controllers provide a means for electrically shutting off the power to the hoist and the energy to physically set the brakes in the event of overspeed, overtravel, undertravel and failure to begin deceleration within sufficient distance

Jan 1, 1976

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935

By Frank K. McIntosh

The Wood mine area was investigated by the Bureau of Mines in -1941 by a magnetic survey and a gravitational survey. Surface trenches were excavated, and diamond-drill holes were bored at the strongest anomalies developed in common by the two surveys. In the last century', several widely separated bodies of chromite with some magnetite had been exploited in a 'serpentine belt near its contact with schist. At one time this district held a virtual monopoly on the production of chromite. Known ore bodies now are exhausted. Owing to the relatively high specific gravity of chromate compared to normal rocks, a gravitational survey was run to determine which magnetic anomalies were worthy of diamond drilling. Linear feet of trenching totaled 1,710 feet. Ten holes were diamond drilled, which totaled 2,272 feet. The log of the drilling is shown in the text in a tabulation of drill-hole data.

Jan 1, 1948

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973