Search Documents

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989

By E. D. Gardner

About five minutes after 3 o'clock on Thanksgiving morning, November 24, 1927, smoke was discovered coming up No. 2 shaft of the Magma Copper Co.'s mine at Superior, Pinal County, Arizona. Of the 49 men in the mine at the time, 42 were able to make their way to the outside unassisted, but 7 perished. Six bodies were recovered, and the seventh, that of an Apache Indian cage-tender at No. 2 shaft, is thought to be in the caved section between the 1,600 and 2,250 foot levels A second and independent fire broke, out in No. 1 shift about 2 a.m., November 27, burning .out the shaft timbers from the surface to the 200-foot level and destroying the surface fan and structures. About 20 men were underground fighting the fire in No. 2 shaft, but all were safely withdrawn, aril the fire in No. 1 haft was quickly controlled.

Jan 1, 1928

Objective A cable bolt can be a strain-measuring device as well as a supporting device in underground mines. Placing instruments on a cable bolt allows certain characteristics of a rock mass, such as high strain and load, to he evaluated during mining and provides a means for mining engineers and mine inspectors to forecast a potential roof fall. Background Thousands of cable bolts are installed in U.S. mines each year. Studies performed by NIOSH researchers show that support loads can exceed the yield point of the steel, which can result in unstable ground conditions that pose direct safety hazards for underground workers. Rock falls can also create secondary hazards, such as caved escape ways and blocked ventilation passages. Development of methods and tools to assist in the evaluation and selection of rock supports could reduce the number of unplanned rock falls significantly. Approach Instrumented cable bolts developed at NIOSH’s Spokane Research Laboratory were used along with existing ground control systems to monitor rock mass loads and movement Axial and shear loads on the cables are determined as these loads are transferred to strain gages embedded in the king wire. In longwall, room-and-pillar, or underhand cut-and-fill mines, rock mass loads and movements can be detected down to microstrains of stress or millimeters of movement. By detecting such small amounts of ground movement and support load, early intervention to prevent a roof fall is possible, and miner safety and health are increased. How it Works Up to 10 strain gages are embedded in the king wire at whatever locations a mine ground control engineer may specify. The gages m either be set in pairs in the same plane to detect shear or set at 90° angles to detect loading in three dimensions. The cables are up to 5 meters long if they arc to be grouted with resin or up to 15 meters: if they will be grouted with cement. They arc capable of holding m ultimate lend of 214 kN and produce reliable readings to 178 kN, as shown in the calibration curve. The cables are fitted with an instrument plug for monitoring the gages and a special head for insertion into the rock. A data acquisition system, such as a Vishay strain indicator box, Campbell Scientific, or Omnidata system, is required to obtain the data for load and displacement calculations.

Nov 1, 1998

By R. E. Stiles

The modified perchloric--EDTA method devised by the Bureau of Mines for the determination of copper in high-grade samples gives results that are more precise and more accurate than those from the classical sulfuric-iodometric method. Although the perchloric--EDTA method is more costly than the conventional method, the savings in time alone largely offsets this difference. Specifically, the modifications wade in the more conventional procedure comprise (1) use of perchloric acid instead of sulfuric acid for dissolution of copper minerals, (2) precipitation of copper as copper sulfide from dilute perchloric acid solution, (3) wet oxidation and dissolution of the precipitated copper sulfide, (4) use of larger amounts of indicator than those employed in the Schwarzenbach method of titrating low-tenor copper solutions with disodium ethylenedinitri10-tetraacetate and murexide indicator, and (5) use of refrigeration to partially stabilize aqueous solutions of the indicator.

Jan 1, 1966

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Twenty-five years ago, the former U.S. Bureau of Mines funded a research project aimed at developing the enabling technology for incipient failure prediction in electric power system components as a means of reducing the injuries and fatalities that sometimes occur when equipment malfunctions. Over the ensuing years, interest in this has waxed and waned, but recently interest has been growing for both civilian and military applications. This paper addresses the level of turn-to-turn insulation deterioration that can be resolved using an on-line monitoring technique. The detection of turn-to-turn defects is especially important because they are believed to represent the beginning stage of most motor winding failures.

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX C SCALING RELATIONSHIPS 1. Scaling Law for Fly Ash Crater Formation The scaling law derived for predicting crater diameters at different scales is developed below by considering the equation of motion of individual fly ash particles. It is assumed that the air drag on each particle is characterized by Stokes flow, and at the borehole - passage intersection the air velocity and the fly ash particle velocity are the same. The equations of motion for a fly ash particle are the following, (see Figure C-1).

Jan 1, 1973

By J. S. Malesky

"INTRODUCTION The Airdox method of breaking coal utilizes compressed air under high pressure and was developed to replace explosives. It is used in Illinois and Indiana mines to a large extent and also has been introduced in mines in a few other States.ACKNOWLEDGMENTThe author gratefully acknowledges the information and photographs furnished by the Cardox Corp.HISTORYIn the early 1920's, with the adoption of mechanical mining in States where on-shift shooting was prohibited, it became desirable to develop some means of breaking coal from the face without the use of explosives. At that time it was thought that a pressure of 20,000 pounds per square inch would be necessary to break the seal. It was impossible to obtain a compressor that would develop this pressure therefore, the 'patentees developed and applied the Cardox method, which utilizes liquid carbon dioxide as the blasting medium."

Aug 1, 1948

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By Florence L. Feicht, Carlton E. Brown

"INTRODUCTION This report contains information on the approximate size of the smallest dust Particles revealed by or the limit of visibility of various microscopic systems. The information was obtained mainly for use in interpreting and evaluating results of number-contentration and particle-size, determinations on, samples of unhygienic particulate matter collected from industrial atmospheres and in developing better methods for determinations nations.Some speculation and even controversy have been published on the limit of visibility of the widely used microscopic system (16-mm., 0.25-or 0.3-N.A. objective, and axial light-field illumination) used in counting the dust in the liquid medium from impinger, 4/ 5/ filter-paper, 6/ and other samples, but little or no quantitative data have been published on the limits of visibility of this or other microscopic' system.ACKNOWLEDGMENTSThe interest, encouragement, and assistance received from H. H. Schrenk, chief of the Health Division are gratefully acknowledged, as is all other assistance received in this study."

Aug 1, 1945

Reduce workers' dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

By Steven R. Davis

Dear Interested Party: Subject: Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals The Department of Natural Resources, Division of Minerals, is seeking outside opinions concerning the leasing of state owned lands far the mining of metallic minerals. Enclosed for your information in a copy of the Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals.

Jan 1, 1994

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961