Search Documents

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By S. F. Ravitz, T. M. Romslo

During 1940 and 1941, the Bureau of Mines examined a large number of silver mines in Arizona for their potential as producers of manganese ores. Although very little manganese ore had been produced from these mines, it was generally known that manganese oxides in appreciable amounts were associated with the silver ore. Following the examinations, the Bureau further investigated some of the ore deposits by diamond drilling and other types of sampling. The results of these investigations, from the viewpoint of manganese, were discouraging. However, the investigations did indicate that appreciable tonnages of manganese-silver ores had been left in some of the mines by earlier operators. Most of these ores were too low-grade for direct shipping as ores of manganese or silver, and their beneficiation by ordinary processes was not economic. Exploitation of the ores appeared to be dependent upon the development of a low-cost milling method, which would yield a marketable manganese product and recover a high percentage of the silver. Later, the Bureau of Mines constructed an experimental mill at Salt Lake City, Utah, for the treatment of manganiferous ores by the dithionate process, designed to recover manganese as a high-grade product. The dithionate residues can be treated by other processes for the recovery of additional values that may be present in the ore. This development focused attention on the manganese-silver ores of Arizona and led to setting up Bureau project No. 370, which is the subject of this report.

Jun 1, 1947

By J. B. Gayle

A half-ton experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial, slot-type ovens. The reasons for constructing an oven of this Size, the details of the design, and the operating characteristics of the oven have been given in previous publications.3/4 The present report deals with the reproducibility of test-oven data and the effects of variations in flue temperature on the physical properties of the cokes produced. Also included are the results of 2,400° carbonizing tests for several coals and coal blends not included in the earlier reports.

Jan 1, 1955

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938

Develop a mobile manipulator that one person can use to lift and maneuver 50- to 600-pound loads. It can be used in maintenance shops and mines to reduce lifting accidents (Figure 1 and 2). Background Lifting heavy items is one of the leading causes of injury in the workplace. Mine Safety and Health Administration statistics showed that, in 2004, back injuries accounted for over 20% of all injuries (1,699 cases) and resulted in 110,000 lost days of work. Forty-one percent of those injuries resulted from materials-handling or maintenance activities.1 In addition to back injuries, lifting injuries include hernias, ruptures, sprains, and strains resulting from losing control of the item being lifted. Factors associated with accidents are weight of the item being lifted, awkward postures, inadequate handholds, and the working environment itself. High accident rates were noted when lifting items that ranged from 50 to 600 pounds, particularly in tight working quarters where maneuverability was critical. Research indicated that a mobile lifting arm would eliminate many lifting accidents in environments where other lifting devices (fork lifts, overhead cranes, mobile A-frames) would not be practical. NIOSH has built a first-generation mobile manipulator unit designed to be used on hard, level floors such as in a shop. The complexity of motion, number of moving parts, compact design, and design constraints of the manipulator required advanced computer-aided design work (Figure 3). As a result of the design work, thirty-eight claims are included in the patent applications. NIOSH will be conducting field trails and working with manufacturers to put the manipulator into industrial use.

Dec 1, 2006

By J. A. Ruppert, P. M. Sullivan

A process was developed on a laboratory scale in which iron contained in galvanizers ' zinc dross and aluminum contained in scrap zinc die - cast alloy were removed simultaneously . Melting both types of scrap together in the proper proportions resulted in formation of solid intermetallic Fe₂ Alg , which was readily removed from the melt by filtration and centrifugation . Recovery was 87 to 92 percent of the available zinc . Refined filtrate contained 0.02 percent iron and 0.20 percent aluminum. Aluminum content was further reduced to less than 0.01 percent by fluxing with zinc chloride . Low temperatures employed and inexpensive equipment requirements make the process commercially attractive .

Jan 1, 1964

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

By W. H. Young

THE BITUMINOUS coal and lignite industry declined slightly in 1961, compared with the 1960 figures. All of the major items, production, consumption, average value, exports, and employment, declined. Even the steady upward trend in mechanization failed to materialize; the percentages of total tonnages mechanically loaded and cleaned remained the same as in the preceding year. However, tonnage per man per day increased from 12.83 tons in 1960 to 13.87 tons in 1961, owing partly to the increased tonnage produced by continuous mining machines. Also, the percentage of total production mined by stripping and by augers increased slightly. Production.-The output of bituminous coal and lignite in the United States in 1961-403 million tons-was 3 percent less than the 416 million tons produced in 1960. Production was retarded in 1961, owing largely to the business recession and reduced exports.

Jan 1, 1962

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By Hal D. Peterson

In research sponsored by the Bureau of Mines, a technique was developed for simulation of heap leaching on uranium ores. The equipment used for this simulation consisted of 2-ft-diam columns, constructed in sections, such that ores as coarse as minus 4-in could be treated in bed depths ranging from 8 to 18 ft with test condition variations. The technique consisted of the separate steps of ore preparation, column loading, charge wetting, leaching, washing, and residue recovery. For the ores studied, sulfuric acid was found to be generally superior to alkaline lixiviants. The rate of uranium extraction by acid leaching proved" to be primarily a function of percolation rate, alkalinity of the ores and oxidant requirements of the ores. Column leaching was closely comparable to field-scale heap leaching in terms of uranium extraction rate and recovery results. Acid and oxidant requirements were lower for the field-scale operation. All column tests, as well as the field-scaly heap, achieved in excess of 96-pct uranium extraction on a Bear Creek, Wyoming ore.

Jan 1, 1985

By James W. Jensen, Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muff ling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the sod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are investigating technology and methods to monitor the blind areas around large haulage equipment used in surface mines. On average, six fatalities a year can be attributed to equipment colliding with other vehicles or pedestrian workers, or backing over the edge of a dump point. Several off-the-shelf technologies exist for monitoring areas that an equipment operator cannot see from the cab, including radar, video cameras, and radio signal detection systems. NIOSH researchers have tested many of these systems on large dump trucks both at their test facility and at surface mines. This article discusses the technologies available for this application and their effectiveness in detecting objects near an off-highway dump truck. Also, guidance is presented for mine safety personnel who are planning to evaluate collision warning systems or cameras on their haulage equipment. Available Technology Over the past few years, the number and types of systems available for monitoring the blind areas around heavy equipment have increased. Systems marketed for the automotive and recreational vehicle industries have been around for a while. Small video cameras can be found

By James V. Kelly

During the spring and summer of 1947, the Bureau of Mines conducted an investigation and core-drilling program in the vicinity of the Rodham mine, approximately 4 miles north of Shullsburg, Wis. This work was undertaken as a part of a general study of the zinc and lead-producing area of southwestern Wisconsin. Work in the Rodham-mine area was done to investigate further a mineralized area frilled in part by the Puritan Exploration Co., a Delaware corporation, with offices in Galena, Ill. Some significant lead-bearing samples were obtained, but no continuous ore body was disclosed as a result of the Bureau of Mines work.

Jan 1, 1949

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947