Search Documents

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By George McCaa, H. C. Howarth

"During recovery operations following a recent coal-mine explosion, 12 small fires were encountered near the break line of pillar extraction in a large panel. All of the fires except one were quickly extinguished by the rescue and recovery parties. This fire had found its way into a large quantity of loose material at a corner of the cut-through between two rooms, about 100 to 150 feet from the break line of an extensive goaf; had it been necessary to seal the fire, the inclusion of this break line not only would have made the work difficult but would have made the section hazardous as it probably would have given off gas. The fire covered a floor space of about 100 square feet and when discovered was burning briskly, with the flame extending to the roof at a height of 3 or 4 feet; it was the cause of much apprehension on the part of those in charge of the recovery operations and resulted in delaying the work considerablyThe object of this article is to describe in detail the method by which the fire was brought under control and finally extinguished, so that other persons encountering similar conditions may have the benefit of the experience.When the fire was discovered a request for rock-dust, fire extinguishers, and other fire fighting equipment was telephoned to headquarters on the surface. The promptness with which fire fighting equipment and material was provided was a big factor in finally extinguishing the fire and illustrates one of the many advantages of a good organization for fire-fighting. Material was transported in mine cars to a point on the main hauling road about 1,200 feet from the fire. It was then carried to the scene of activity by workmen. The first material to be delivered at the fire was a number of fire extinguishers of various types. The contents of 30 to 35 of these were discharged on the fire and with the aid of a small quantity of rock-dust were sufficient to smother the flame temporarily. It was the opinion of several persons who were present when the fire extinguishers were used that the acid-soda type of extinguisher gave more effective results than the two or three other types used.When the contents of all of the fire extinguishers had been exhausted the fire was temporarily smothered, but as there appeared to be danger that the flame would burst forth again, means for completely extinguishing the fire were"

Feb 1, 1929

By George A. Morgan

The 53 countries that constituted Africa in 1989 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant minerals to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, and the titanium minerals-ilmenite and rutile, vanadium, vermiculite, and zircon. Despite the underdevelopment of much of Africa, mineral raw materials played a very important part of the national economies of many of its countries. In terms of percent-age of export earnings, minerals accounted for more than 90% in some cases. In several countries with agrarian economies and little economic diversification such as Angola and Guinea, a single mining operation could represent an important source of foreign exchange. These latter operations tended to be the more easily mined surface deposits of diamond, gem stones, and precious metals. Mineral commodities for which Africa had a high percentage of world output were bauxite, 16%; chromite, 44.5%; cobalt, 76.5%; copper, 13.9%; diamond, 50.7%; gold, 32.9%; manganese, 27.1 %; phosphate, 22.1 %; platinum-group metals, 48%; uranium, 29.2%; vanadium, 54%; and vermiculite, 41 %. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States.

Jan 1, 1992

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers' methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981

By James R. FitzSimmons

This report describes an instrument developed by the Bureau of Mines as an improved device for examining roof rock in bolt holes. The unit consists of a commercially available fiberoptic unit adapted for use as a flexible stratascope. Field testing in both metal and coal mines has shown the instrument can be easily transported and used by a single operator. The size and flexibility of the instrument eliminate the need for specially drilled holes.

Jan 1, 1979

By R. V. Lundquist, H. Leitch

The solubility characteristics of mono calcium aluminate (CaO A₁₂ 0 ) in water and in NaOH , Na₂ CO₂ , and NaOH - Na₂ CO₂ solutions were measured by determining the changes in Al2O3 concentrations in solution over a period of time at a specified temperature . The monocalcium aluminate was synthesized by sintering its starting components for 72 hours at 1,375 ° C. Distilled water and aqueous solutions of technical grades of NaOH and Na₂ CO₂ were used as solvents . The extraction of alumina from the monocalcium aluminate was dependent on the composition of the solvent and partially dependent on temperature for leaching . About 98 percent extraction of alumina from the aluminate occurred in Na₂ CO3 solutions containing 10 to 12 percent NaOH . Other solution compositions produce lesser extractions .

Jan 1, 1963

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By N. Kumar Kittusamy

Operators of construction equipment perform various duties at work that expose them to a variety of risk factors that may lead to health problems. A few of the health hazards among operators of construction equipment are: (a) whole-body vibration, (b) awkward postural requirements (including static sitting), (c) dust, (d) noise, (e) temperature extremes, and (f) shift work. It has been suggested that operating engineers (OEs) are exposed to two important risk factors for the development of musculoskeletal disorders: whole-body vibration and non-neutral body postures. Method: This review evaluates selected papers that have studied exposure to whole-body vibration and awkward posture among operators of mobile equipment. There have been only few studies that have specifically examined exposure of these risk factors among operators of construction equipment. Thus other studies from related industry and equipment were reviewed as applicable. Conclusion: In order to better understand whole-body vibration and postural stress among OEs, it is recommended that future studies are needed in evaluating these risk factors among OEs.

Jan 1, 2004

By Ronald H. Church

As part of the Bureau of Mines health and safety research program in strata control, a ground-penetrating radar (GPR) system capable of pene-trating approximately 10 ft into the mine roof has been devised to identify anomalistic conditions. The GPR system consists of a transmitter with carrier frequencies of 250, 500, and 1,000 MHz, utilizing a dipole antenna, and a receiver, consisting of a dipole antenna fed into a sampler with a time base housed in a storage oscilloscope. A computer was utilized for data acquisition and data processing. Data analysis by computer enhancement revealed recognizable return ra-dar signatures from the middle man rock and main roof of the test site. These stratigraphic anomalies can be cataloged for recognizable fea-tures, which from the past history of the mine may have been shown to create strata control problems. Early recognition of such features could lead to immediate corrective actions and result in the saving of lives.

Jan 1, 1985

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Steven J. Page

Longwall double-drum shearers frequently have difficulty complying with the 2.0 mg/m3 dust standard and, therefore, require the use of effective dust controls. However, before dust controls can be implemented effectively, the major individual dust sources must be determined and their relative severity evaluated. The Bureau of Mines has recently developed a sampling strategy, based upon short-term gravimetric sampling, that can identify the major dust sources contributing to the shearer operator's exposure. This technique utilizes approved gravimetric sampling equipment already available to all mine operators and can be performed by two people in 2 days. Five examples, including data analysis, are discussed with respect to various cutting sequences. In addition, typical dust source contributions obtained from studies of double-drum shearer operations regularly in compliance are included. Mine operators can thereby compare their dust source evaluation results with those from these longwalls.

Jan 1, 1982

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974