Search Documents

By W. H. Eddy

The Bureau of Mines used several laboratory batch flotation schemes combined with magnetic separation to investigate the feasibility of recovering potash feldspar and glass sands from molybdenite tailings. Four molybdenite tailings or prospective tailings were used as test samples. Feldspar concentrates containing from 10.7 pct to 12.0 pct K2O were recovered from three of the four samples. The alkali content of the fourth sample met the grade for a mixed feldspar. All the feldspar concentrates contained iron in excess of the 0.10-pct-Fe203 specification for most uses. Electron-beam microprobe examination of the feldspar concentrates showed the presence of an iron-bearing potash feldspar in quantities that were excessive with respect to most iron specifications. However, a high-quality glass sand was produced from all of the samples.

Jan 1, 1980

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

By H. B. Carroll

The Bureau of Mines has designed and built a controlled-environment test chamber specifically for instrument evaluation in simulated work atmospheres. The atmosphere inside the 300-liter stainless steel chamber can be controlled at any selected temperature and relative humidity in the range of 2° to 93° C and 20 to 95 percent, respectively. Instruments placed inside the test chamber are subjected to an atmosphere at a preset temperature and humidity containing various concentrations of toxic gases such as CO, C02, NO, NO2, S02, and H2S. Toxic gas losses resulting from wall reactions, monitoring instruments, and instruments under evaluation are compensated by the use of a dynamic gas blending system.

Jan 1, 1973

By J. H. Jacobs

In late 1946, research was begun at the Bureau of Mines Electrometallurgical Laboratory at Boulder City, Nev., to determine the possibility of electrowinning manganese from chloride electrolytes on a continuous basis. All phases of electrodeposition were investigated on a small scale it the laboratory, and the results were reported by Jacobs and Churchward. These results indicated that a chloride process had certain possible advantages over the sulfate process that made it worthwhile to continue the investigation on a semi-pilot-plant basis, and this paper reports the results of this work. Research and development work on a process for electrowinning manganese from low-grade ores has been carried on intermittently by the Bureau of Mines since 1936. A process was developed, using sulfate electrolyte, that has been extensively described in the literature.

Jan 1, 1951

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes Initial capital investment ranges from $26,498,500 for the 1.03- million-ton-per-year (MM tpy) mine to $67,173,300 for the 3.09-MM-tpy mine. Total capital investment ranges from $37,437,500 to $92,984,300 for the same mines. Corresponding selling prices for the coal range from $14.83 to $13.26 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1975

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By J. E. Fraley

This report describes the preliminary results of a Bureau program to develop and test an inexpensive grout for full-column support of roof bolts. Various inorganic grouts were tested in both cartridge and slurry form. Tests were also performed on methods of water packaging and on the effect of fillers on the grout strength. Results showed that some grouts had poor early strength and exceptional mid-to long-term strength. Laboratory tests have shown that rapid-setting inorganic grout could be an economical replacement for resin bolts if the short-term strength could be increased. Further development to improve its early strength would need to be tested in the laboratory and underground to prove its potential for the mining industry.

Jan 1, 1987

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,540,700 for the 1.06-million-ton-per-year (MM tpy) mine to $44,720,500 for the 4.99 MM tpy mine. Total capital investment ranges from $21,850,700 to $75,693,500 for the same mines. Corresponding selling prices for the coal range from $8.76 to $7.53 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

By C. E. Coleman, Joseph D. Davis

During some distillation experiments conducted by the Bureau of Mines in cooperation with the Trent Process Corporation it was observed that amalgams of heavy petroleum oils and finely pulverized coal tended to produce a denser coke than that obtainable from the coal when retorted alone . Even anthracite coal when retorted with oil yielded a coke . This led the writers to believe that by mixing a lowrank coal ( sub-bituminous or even lignite ) - with asphaltic oil and retorting it, a coke suitable for domestic fuel could be made . Thus there was contemplated the production of domestic coke and the utilization of a low- grade oil in one operation . - In order to decide on the practicability of this process , it was necessary to know the value of products obtainable by such a method , as compared with those obtained by separate distillation . A laboratory method was therefore devised , and while it was realized that no small - scale testing apparatus for destructive distillation gives results that are directly applicable to commercial - scale operations , by keeping distillation conditions uniform for comparative tests , results were obtained valuable for purposes of comparison . The plan was to distill mixtures of coal and oil in a laboratory retort , and then distill the constituents separately under the same conditions . The comparative quantities of products yielded were thus directly obtained , and their quality was determined by analysis . The following are the main points investigated : ( 1 ) Quantity and quality of coke ; ( 2 ) Quantity of oils boiling below 221 °C . ( gasoline stock) and oils boiling at 221 to 300° C . ( kerosene stock) ; and ( 3) Quantity and quality of gases .

Jan 1, 1922

By R. S. Sanford

The Claim Point chromite deposits are at tidewater near the southern tip of the Kenai Peninsula in southwestern Alaska, The United States Geological Survey had a field party in the region from July until September 1940 under P. W. Guild, assistant geologist; maps and geological data were assembled and made available to the Bureau of Mines. A preliminary investigation of the deposits at Claim Point by the senior author during July 1941 was followed by surface sampling and core drilling to determine the quantity and grade of the ere, The Geological Survey was represented at the project by George O. Gates, geologist. Cores were checked and the structural data revealed by drill cores were interpreted. The principal chromite deposits have been sampled and delimitated by trenching and core drilling. Other deposits were trenched and sampled but were too small or too low-grade to warrant core drilling.

Jan 1, 1949

By Gerrit V. R. Goodman

A laboratory study assessed the impacts of water spray pressure, face ventilation quantity, and line brattice setback distance on respirable dust and SF6 tracer gas concentrations around a continuous mining machine using a sprayfan or directional spray system. Dust levels were measured at locations representing the mining machine operator and the standard and off-standard shuttle car operators, and in the return airway. The results showed that changes in all three independent variables significantly affected log-transformed dust levels at the three operator sampling locations. Changes in setback distance impacted return airway dust levels. Laboratory testing also identified numerous variable interactions affecting dust levels. Tracer gas levels were measured on the left and right sides of the cutting drum and in the return. Untransformed gas levels around the cutting drum were significantly affected by changes in water pressure, face ventilation quantity, and setback distance. Only a few interactions were identified that significantly affected these concentrations. Gas levels in the return airway were grouped by face ventilation quantity. Return gas levels measured at the low curtain quantity were generally unaffected by changes in water pressure or curtain setback distance. At the high curtain quantity, return airway gas levels were affected by curtain setback distance. A field study was conducted to assess the impact of these parameters in an actual mining operation. These data showed that respirable dust levels may have been impacted by a change in water pressure and, to a lesser extent, by an increase in curtain setback distance. A series of tracer gas pulse tests were also conducted during this study. The results showed that effectiveness of the face ventilation was impacted by changes in curtain flow quantity and setback distance. Laboratory testing supported similar conclusions.

Jan 1, 2004

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau&apos;s process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

By Christopher H. Roe

This Bureau of Mines report reviews the various methods of removing the liquid from tailings slurries that contain very fine grained solids. Gravitational settlement, centrifugation, filtration, and thermal drying methods are discussed in detail. Chemical additives, electrokinetic dewatering, and the rotary trommel screen are also mentioned. Lists of dewatering equipment and suppliers are given in the appendixes to assist the planner who must choose the most efficient, economic, and practical method of dewatering very fine grained mill tailings.

Jan 1, 1984

By G. S. Scott

Safety problems in the mining and allied industries have led the Bureau of Mines to investigate over a period of years; the flammability (explosibility) of many types of combustible atmospheres principally at ordinary pressure; the results of these investigations have been made available as a bulletin. However, more recently, the demand for information on the flammability of gaseous mixtures at high and low pressures has increased greatly. In particular, the rapid development of high-altitude aviation has brought demands for information on the flammable (or explosive) characteristics of certain gases and liquids at low pressures. The present report gives the results of about 900 tests made to determine the flammability of the lighter paraffin hydrocarbons mixed with air and nitrogen at pressures of 400 200, 100 and 70 ram. Hg. The gases tested include natural gas, methane, ethane, propane normal butane and isobutane. The minimum pressures at which these gases are capable of propagating flame whorl individually mixed with air also were investigated.

Jan 1, 1952

By J. E. Dooley

A mass spectral scheme of analysis was devised which can be used to identify individually a single compound from a larger group of similar compounds. Mass spectra for 32 alkyl aryl sulfides are provided for future reference work, and analytical correlations used in producing the analytical scheme are discussed. Some of the correlations show that base peaks are either the same mass as the parent peaks or may be derived from cleavage alpha to the sulfur atom with migration of one hydrogen to the sulfur atom. Other spectral consistencies provide means of separating ortho-, meta-, and paratolyl arrangements in an overall analytical scheme. Determinations of chain lengths and separation of isomeric species are also discussed.

Jan 1, 1972

By Jack Wasserman, Don Wasserman, Logan Mullinix, Shekhar Khanal, Kelly Neal

This paper presents current finding on truck driver average exposure to acceleration for several different manufacturer’s cab-over trucks on a variety of roads in different countries. The predominant time, for this aspect of the study has been spent in the area around London, England and Warsaw, Poland. The ECE directive 2002/44/EC has provided specific guidelines for vehicle operators 8 hour average acceleration exposure. The primary considerations have been on truck design including the air-ride driver’s seat. The truck manufacturers have produced truck cabs that have some separate suspension from the truck frame. The truck seat manufacturers have been producing air-ride suspension seats for the cab. Both of these designs have had the objective of meeting the ECE directive and providing the vehicle drivers with some degrees of comfort. This paper will provide some information on the ability of the vehicles to operate on a variety of roads and meet the objectives. Method The primary method for evaluation of the driver’s exposure has been the use of a seat pad attached to the driver’s seat. Although this sensor system provides the critical information for the driver, an understanding of the reasons for the values requires additional measurements. The initial study in England used both driver and passenger seat pads, as shown in Figure 1, as well as triaxial accelerometers mounted on the base of the seat. The latest studies used significantly more transducers to better understand the relative rotations and translations on the truck frame, the cab, and the driver. [ ]

Jan 6, 2006