Search Documents

During 1990-1999, a total of 458 fires occurred in all coal mining categories; 157 of those fires caused 164 injuries and 2 fatalities. The greatest number of fues and fire injuries occurred at surface mines, whch also had the highest risk rate values. A total of 66 fuefighting interventions were required. Of these, there were 25 mine rescue team interventions in underground mines, including 5 mobile equipment firefighting interventions, and 41 fire brigade and fire department interventions at all surface operations, including 19 mobile equipment interventions. In all, 50 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 1 14 fires were detected late by smoke, and 42 fires were not detected.

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By John K. Alley

Fibrous silicon carbide was produced by thermal decomposition of certain silicates contained in graphite crucibles. Induction heating was used to produce the necessary temperature and thermal gradients. Both green and white fibers were mainly the beta modification even though each color grew within a different temperature zone. Alpha silicon carbide, present in insufficient amounts for X-ray detection, was identified by electron diffraction. The white fibers formed in a zone between 1,365° and 1,634° C (±50° C). The green fibers (less contaminated) formed in a much more narrow zone between 1,650° and 1,672° C (±50° C). The average lengths and widths of microscopic fibers grown by this method were 1.5 mm/0.002 mm (white) and 1.2 mm/0.0035 mm (green); however, same fibers observed by electron microscope had cross-sectional measurements of 150 to 300 A. Both differential thermal analysis and thermogravimetric analysis showed that silicon carbide fibers oxidized in air at temperatures above 500° C. Fibrous silicon carbide was indexed as a cubic cell with the dimensions a = 4.358 A. The density calculated from X-ray data was 3.217 g/cm3.

Jan 1, 1963

By J. Roger Loebenstein

ASARCO Incorporated, the only domestic arsenic producer, terminated copper-smelting operations and the associated recovery of byproduct arsenic trioxide at Tacoma, W A. in 1985. It still shipped small quantities of trioxide from its remaining stocks in 1987. Imports for consumption of arsenic trioxide were slightly higher than in 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1989

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature on the nonmetal binary and ternary compounds of the group IVB, VB, and VIB elements, with emphasis directed to the following nonmetals: B, C, N, O, and Si. This review examines each of these binary and selected ternary compounds of the group IVB, VB, and VIB elements as coatings and gives some of their preparative methods, uses, and properties. A total of 259 references were found for these compounds of the nine elements. This review was utilized in the Bureau's research to provide abrasion-, erosion-, and corrosion-resistant coatings in order to conserve critical metals and protect various metallic surfaces in metallurgical, mining, and energy conversion systems.

Jan 1, 1983

By M. M. Tilman

A series of alloys was laboratory prepared by adding up to 4 weight-percent cobalt to the basic composition of type AM 350 (AISI 633) stainless steel. Aging curves were established for each alloy at 750° F, 850° F, and 950° F for lengths of time up to 100 hours. A series of annealed steels containing as much as 1 weight-percent cobalt was cold-rolled 50 percent and aged for 3 hours at 850° F. No improvement in hardness due to cobalt was observed in the steels transformed by heat treatment. Slight improvements in hardness were observed in the steels transformed by cold working.

Jan 1, 1968

By E. Aamland

Preparation of high-purity magnesium-yttrium alloys by electroreduction of Y2O3 dissolved in a YF3-LiF bath and the subsequent deposition of yttrium in a molten magnesium cathode was investigated in laboratory-scale apparatus. Parameters such as temperature, current density, and electrolyte density were studied. Electrolysis was conducted in a specially designed MgO diaphragm cell at temperatures ranging from 780° to 970° C. Alloys containing up to 55 weight-percent yttrium were prepared at cathode current efficiencies of 21 to 60 percent. Cell design and operation are described, and some of the limiting conditions pertaining to the method are discussed.

Jan 1, 1973

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC) , on Contract H0122026 (which began in August of 1971) . Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of in- dependent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "seismic Detection and, Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971