Search Documents

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By Ray J. Holmquist

"INTRODUCTION The Copper King or Red River copper mine was examined on December 13, 1942, by the Bureau of Mines at the request of Richard Kelly of Santa Fe, N. Mex. The examination was made to determine whether the expenditure of funds for rehabilitation work necessary to make the workings accessible for examination would be warranted.As a favorable report was made, the workings of the Copper King mine were opened and sampled under the direction of the author. The portal of the Copper King adit was opened first. Considerable rehabilitation was necessary in the first 50 feet of the workings, but the remainder of the drifts and crosscuts were sufficiently open to permit surveying and sampling.An attempt was made to open the Waterbury atilt, which was reported to be about 30 feet east of the Copper King portal, and to crosscut the ore body nearly to its southern border. However, slide rock and mine dumps had completely obscured the portal of this adit, and no opening into it could be found or made.Work on the project was started on September 27 and vas completed on November 6, 1943."

Apr 1, 1947

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By E. A. Barrett, K. M. Kowalski

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent- image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3- D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 1995

Develop a means for estimating vertical stress conditions in or around an underground mine so that appropriate measures for ground control can be taken before hazardous conditions arise. Background High vertical stress in an underground mine could cause or enhance hazardous ground control conditions which might lead to accidents, fatalities, and loss of reserves. An understanding of the vertical stress conditions at the mining level would allow a mine operator to take precautions that will minimize the occurrence of ground control problems. A knowledge of the underground stress conditions prior to mining could be used as an aid in future mine plan development to avoid or minimize ground control problems. Approach The Bureau of Mines developed a computer program for calculating the vertical stress resulting from the pressure of overlying rock masses on a mine or geologic surface at various depths.

Jan 1, 1990

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987

By Allan F. Smith

The Bureau of Mines studied toxic products produced by burning eight fire-resistant mines conveyor belts, a brattice cloth, and an electrical cable insulation obtained from laboratory-scale burning experiments under various air-flow conditions. Generally, CO product concentrations for most materials were noticeably higher then the NO2 and HC1 levels that were measured; also, no phosgene was detected. However, several of the fire-resistant belt samples yielded HC1 concentrations that were above the reported lethal level for 1/2 to 1-hour exposures, although these data were limited to flow conditions where air dilution effects were small; the belt materials that showed this behavior included samples of polyvinyl chloride, styrene butadiene, styrene butadiene blends, and a British neoprene which yielded the greatest amount of toxic vapor. In addition, some results are presented on the phosphoric acid concentrations that may be produced from the decomposition of ammonium dihydrogen phosphate when dispersed on a burning coalbed.

Jan 1, 1973

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

The first phase of our work for PMSRC on this contract was devoted to a comprehensive and in-depth assessment of electromagnetic (EM) noise measurements and data taken by several contractors for use in the design of operational and emergency mine communications. Pertinent measurements and data of other selected investigators were also included in the evaluation. This assessment treated the measurements and instrumentation used, the data analysis and presentation methods, and the utility of the final results. This phase concluded with the identification of the most useful results and methods, the remaining data gaps, the contractor most qualified to fill these data gaps, and the definition (with PMSRC and this contractor - NBS, National Bureau of Standards) of a follow-on noise measurement program, instrumentation system, and data processing methods tailored to obtain the necessary but missing noise data. A partial bibliography of references related to electromagnetic and seismic noise and propagation in the frequency bands of interest was also compiled during this first phase. The body of this Part of the final report presents a summary of the findings of our EM noise assessment, together with detailed recommendations regarding the new noise measurements to be taken and the instrumentation and data processing methods to be used. This work was done during the latter part of 1971 and the early part of 1972. During subsequent phases of the contract ADL was asked to perform on-going evaluations of the continuing program of electromagnetic (EM) noise and propagation measurements made by Bureau contractors, and to utilize pertinent data from these measurements to make performance estimates for

Jan 1, 1974

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

In 2005, a total of 2,063 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.1% of all mining operations. ? Bituminous mines comprised 92.6% (n=1,911) and anthracite mines 7.4% (n=152) of coal mining operations. ? Approximately 70% of all coal mines were located in three states: Kentucky (28.0%), West Virginia (21.8%), and Pennsylvania (20.6%).

Jan 1, 2008

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By K. J. Liles

To encourage the development and conservation of the Nation&apos;s ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986

In 2006, a total of 2,113 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 14.2% of all mining operations. ? Bituminous mines comprised 92.5% (n=1,955) and anthracite mines 7.5% (n=158) of coal mining operations. ? Approximately 71.0% of all coal mines were located in three states: Kentucky (29.2%), West Virginia (21.8%), and Pennsylvania (20.3%).

Jan 1, 2008

By M. D. Carver

This publication describes development by the Bureau of Mines of a quality evaluation procedure for certifying the adequacy of production lots of Kroll process zirconium sponge the Bureau had produced for reactor applications. After the procedure was devised, the next step was to apply it in controlling the quality of one-half million pounds of zirconium sponge com-prising 259 production lots, called blends, originating at the Metallurgy Research Center of the Bureau at Albany, Oreg. The Bureau concluded that the evaluation method developed was adequate and that by this method the zirconium blends having impurity levels or other property values outside specification limits were differentiated and thus were diverted from nuclear energy end uses. The research was performed under contract for the Bureau of Ships, Department of the Navy, and for the Atomic Energy Commission (AEC).

Jan 1, 1960