Search Documents

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By William W. Adams

A new record in accident prevention was made by the metal-mining a industry of the United States in 1938, as signalized by a lower fatality rate than in any previous year. The rate was less than half as high as in 1911, the earliest year for which figures are available. A good safety record was also established in the prevention of nonfatal injuries, as the injury rate was lower than in any other years except 1931 to 1935, a 5-year period notable for its unusually low injury rates. Employment was more limited in 1938 than in 1937, both in number of men employed and total number of man-hours worked. The number of workdays per man also was smaller than in 1937. Operating companies reported that 7,233 mines were active in 1938 or some part of the year and that the total number of men employed was 103,027. This figure represents the summation of the average number of men employed as reported by the companies, the average for each mine being that for the period during which the mine was active. The number of employees at all mines in 1938 was 15,402 less than in 1937. Reports covering all mines indicated a total of 188 million man-hours worked during the year, or 21 percent less than the nearly 240 million man-hours worked in 1937. In the performance of this work accidents occurred that resulted in the death of 156 employees and the injury of 1.2,722, each injured employee being disabled for more than the remainder of the clay on which he was hurt.. The fatality rate for 1938 was 0.83 per million man-hours worked, which was 9 percent more favorable than the rate of 0.91 for 1937. Nonfatal injuries occurred at the rate of 67.61 per million man-hours worked, an improvement of 10 percent compared with the injury rate of 75.37 for 1937.

Jan 1, 1941

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By H. J. Rose, H. H. Lowry

Considerable information on the organization of German fuel research and recent developments was obtained and published in several combined Intelligence Objectives Sub-Committee Reports. This material, although avail- able in the initial reports, has never been consolidated, so that it may not have come to the attention of many readers. This report gives a summation of the authors' observations at six different research laboratories.

Dec 1, 1947

By Gerald R. Smith

Because of continuing concerns regarding the effects of cumulative quantities of materials in the environment, the Bureau of Mines has initiated a series of studies to evaluate, to the fullest extent possible, all aspects of the materials flow sequence fur selected commodities. Although tungsten and its compounds do not pose a significant health hazard to the environment, they do represent valuable resource materials to which appropriate conservation considerations must be given. The present study includes a description of recent trends in the consumption, loss, and recycling of tungsten-containing materials in the United States during the period 1974 to 1991 and an estimation of the cumulative loss of tungsten to the environment since 1910. Obsolete tungsten is recycled primarily as cemented tungsten carbide components that have been used in cutting and wear-resistant applications. The quantity recycled, as a of annual U.S. consumption of tungsten, was estimated to have increased from 10% in 1974 to 341a in 1991. An estimated 58% of the 148,000 metric tons of primary tungsten consumed since 1910 was lost to the environment through means such as dissipation, discard, and dilution.

Jan 1, 1994

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By Chas. F. Jackson

This paper is one of a series dealing with special mining problems and forming part of a general study of mining, methods and costs being conducted under direction of the Bureau of Mines. A considerable part of the material assembled and discussed in this paper has been gathered from articles on individual mines written by consulting engineers to the bureau who are engaged in active mine operation at the properties described, while other data have been taken from the technical press or gathered from personal observations. OBJECT AND SCOPE OF PAPER C. F. Jackson4 ha[-] pointed out that underground transportation (tramming, haulage, and hoisting) absorbs an appreciable percentage of the total underground cost of most mines, averaging for different methods of mining 12.9 to 28.4 per cent of the total underground cost. In general the percentage of cost accounted for by transportation was shown to be highest for the low-cost mining methods.

Jan 1, 1931

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By A. C. Fieldner

In 1927 the Carbonization Committee of the American Gas Association proposed cooperation with the Bureau of Mines in the development of suitable methods for determining the carbonizing properties of American coals. It was further proposed to apply these methods in the testing of representative coals and to make the information obtained available to the public through Government publications. A cooperative agreement was signed whereby the Gas Association contributed part of the funds necessary for beginning the project and appointed a committee to consult and advise the Bureau in the work. The Advisory Committee has been reappointed each year, and the Bureau has had the benefit of its advice. The composition and carbonizing properties of 33 coals previously tested have been given in technical papers of the Bureau of Mines and in short reports published for the most part in the Proceedings of the American Gas Association. A complete list of publications on the work previous to 1937 is appended to this report. The present report gives the composition and carbonizing properties of seven additional coals from West Virginia. The data include results of blending tests in which Beckley led low-volatile coal was used with all the high-volatile coals except the Alma coal, with which Pocahontas No. 4 coal was used.

Jan 1, 1938

By IRENE AITKENS

The emerald is the most costly of all gems , due to the scarcity of flawless stones . This fact gave rise to the ancient axiom , " As rare as an emerald without a flaw . The finer gems not only command the highest prices at all times , but when flawless are considered the most highly prized of all gem stones . George F. Kunz divides emeralds into two distinct classes : " Exceptional specimens , " which bring as much as $ 6,000 a carat ; and " fine- quality specimens , " which bring about $ 1,000 a carat .

Jul 1, 1931

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural- gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas, in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and In solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil- bearing horizons.

Jan 1, 1936

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By Henry Kreisinger, F. K. Ovrrz, C. E. Augustine

The Bureau of Mines is conducting investigations to determine how fuels belonging to or for the use of the United States Govern- ment can be utilized with greater efficiency. As a result of these investigations a number of reports have been published, each report treating of one phase of fuel utilization. A list of these publications is given at the end of this bulletin. The efficient utilization of coal depends on the correct design of furnaces and on their proper operation. To attain both of these conditions a knowledge of the fundamental principles of combus- tion is necessary. Therefore, the study of the combustion of coal in industrial furnaces has been made a part of the bureau's fuel in- vestigations. The desirability of investigating the fundamental principles of combustion was suggested by the study of a large number of steam- ing tests made by the fuel-testing division on coals from all of the more important fields in the United States. The results of these tests have been published in Bulletin 325 of the United States Geological Survey and in Bulletin 23 of the Bureau of Mines. As a result of that study a plan to investigate the combustion of coal in a special apparatus in which all conditions could be controlled was presented to the National Advisory Board for Fuels and Struc- tural Materials at its meeting of April 10 and 11, 1906. The plan received the approval of the board, and since the establishment of the experiment station of the Bureau of Mines at Pittsburgh the investigation of the combustion of coal has been carried on intermit- tently. The history of these investigations is given in Technical Paper 63.

Jan 1, 1917

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By D. Harrington

We Americans pride ourselves that ours is the greatest, most advanced and most civilized nation in the world, yet statistics indicate that apparently we have little appreciation for the lives and limbs of the people whose efforts give us whatever greatness we possess. The latest available statistics indicate that the annual accident death rate per 100,000 of population is nearly 80 or far higher than that of any other country in the world except Chile; is more than double the rate in Hungary, Netherlands, Ireland, Belgium, Denmark, Italy, Germany, Norway, Sweden, and Finland; is nearly double that of England, Wales, the Union of South Africa, New Zealand, Japan, Australia, and Scotland; and is 25 to 40 percent greater than Switzerland, France and Canada. To make matters worse, from the viewpoint of mining; the latest available statistics give mining by all adds the worst accident rate of the major industrial occupations in the United States, the accident severity rate for mining in 1935 being listed by the National Safety Council as 10.14, the next highest rate being 4.52 for construction, and the average rate for 30 main industries being 1.58. IMPROVEMENT IN SAFETY RECORDS Offsetting to a slight extent this rather dark picture is the fact that starting about 1930 the mine-accident rate in both coal and metal mining began to fall, reaching an all-time "low" in metal mining in 1932 and in coal mining in 1933. It now appears probable that the year 1936 has again lowered the accident rate in coal mining and this, together with the fact that the years 1933, 1934, 193 5, and 1936 all set much lover accident rates in coal mining than ware achieved for any similar previous period, gives hope that the trend is definitely in the right direction, though from the above figures mine-accident severity has a long, tedious road to travel before it becomes as low as the severity rate of all other major industries in the United States.

Jan 1, 1937

By Frank Cook

In this two-year study, an evaluation of mining and reclamation practices at 159 randomly sampled surface coal mines in the United States was conducted. It is concluded that reclamation practices in most of the 22 coal-producing states were adequate during 1975, but that improvement in reclamation performance was desirable in the acid area of the central U. S. and in mountainous southwestern Virginia. Productivity improvements should result from research to determine efficient or optimal operating procedures for dragline stripping of single and multiple seams, surface mining of lignite, multicut and multiseam haulback mining on steep slopes, mountaintop removal, and surface mining in swampy or deeply glaciated areas. Specific candidate research projects are discussed in this report.

Jan 1, 1976

By E. K. Stanek

This report contains the results of several related research efforts, all of which were aimed at enhancement of mine power system safety and reliability. The largest single effort was on optimum spares and maintenance scheduling for various components of a mine power system. Two closely related tasks involved calculation of the minimum arcing faults that could occur on dc trailing cables and the use of trippable load break switches to clear ground faults. Both of these tasks are concerned with reliable fault clearing to prevent shock and fire hazards. Three other closely related tasks were concerned with aspects of mine power system design: (1) alternate network topologies, (2) optimum voltage selection for mine power systems, and (3) selection of system components. The other research task consisted of laboratory tests to ascertain the effects of repetitive, low-level transients on insulation systems.

Jan 1, 1979

By Steven R. Davis

Voyageurs National Park in northern Minnesota, and a 30-mile radius area of influence on the United States side of the International Border, was examined for hardrock (nonferrous metallic minerals and diamonds) mineral potential and environmental sensitivity by the U.S. Bureau of Mines. The investigation also included an analysis of current Metallic Minerals Leasing Rules of the State of Minnesota, and the probable effects of changes proposed to the current rules by the State of Minnesota in order to "encourage mineral exploration and development." The study has determined that the proposed changes to the Minnesota State Leasing rules will have minimal, if any, impact on the likely, foreseeable levels of mineral-related activities in the State as a whole, and particularly, in the area of influence to the Park. Voyageurs National Park management was advised on the extent and character of the proposed rules changes, and on those items of concern meriting a specific and timely response by the National Park Service.

Jan 1, 1994