Search Documents

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By N. S. Dalal, Xianglin Shi

"INTRODUCTIONEpidemiologic studies of workers in chromate-ore related industries, 1-3 and stainless steel welding and related occupations4 have shown that they have about 20-40 times higher risk of throat or respiratory track cancer than controls. Although the actual carcinogenic substances were not identified in these statistical studies, Cr(VI) compounds (for example, calcium chromate, zinc chromate, and lead chromate) were implicated as the causative agents, whereas Cr(III) compounds were not suspected as carcinogens. s These suggestions were supporte4 by laboratory studies wherein many Cr(VI) compounds produced sarcomas at the implant or injection sites.1,5 Squamous cell carcinomas and adenocarcinomas closely resembling human lung cancer were induced by intrabronchial implants of calcium chromate in rats, 6·7 whereas Cr(DI) oxide and Cr(lll) sulfate did not induce any tumor formation.6,7While the mechanism of the chromate-induced carcinogenicity is not fully understood, it is generally thought8 that it involves some damage to DNA. Specifically, it has been reported that: a) the chromate ion, henceforth referred to as chromate, can pass through the cell membrane and enter the cell while CR(DI) does not, 9 b) chromate does not interact with either native or denatured DNA 10 while Cr(III) does, 11 and c) the final Cr-DNA complex isolated from cellular reactions of chromate is Cr(III)-DNA, with Cr(III) binding to the phosphate groups.12,13 Thus the important question is: since Cr(DI) cannot pass through the membranes, how does Cr(III)-DNA complex form? For this to happen, Cr(VI) must be reduced to its lower oxidation states, 14 ultimately to Cr(III), by some reductants in the cellular environment. Unless this reduction occurs, the DNA would not be damaged and therefore no chromate carcinogenicity would ensue. Thus the reduction of chromate to its lower oxidation states seems to be a key step in the chromate carcinogenicity .1s One of the major reductants in cellular environments is thought to be glutathione (GSH), both outside and inside the cells.16-lB Some evidence for the role of GSH in the chromate toxicity was provided by recent studies showing that exposure of hamster cells to non-toxic levels of added selemite increases the levels of GSH as well as the Cr(VI)-induced DNA strand breaks,19 and that such DNA strand breaks in hepatocytes also change in direct proportion to the GSH content. 20,21 These observations were interpreted as implying that the reduction of chromate by GSH to some reactive intennediate is an important step in the chromate carcinogenicity. 20.21 In · the present undenaking22 we have used electron spin resonance (ESR) and spin-trap methodology to investigate the reduction of chromate by GSH and find evidence for the involvement of the glutathionyl radical (GS ·) as well as Cr(V)-intermediates."

Jan 1, 1990

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) spin trapping experiments have been carried out to investigate the mechanism of sulfite oxidation em¬ploying 5,5-dimethyl-l-pyrroline-1-oxide (DMPO) as a spin trap. The results show that sulfite autoxidation, catalyzed by Mn(II), involves not only the SO-3 radicals but also the •OH radicals. An addition of H2 02 to the sulfite aqueous medium significantly increases the •OH radical formation. This result provides new clues to the chemical mechanism of the sulfite oxidation and the sulfite toxicity.INTRODUCTIONStudies of the oxidation of the sulfite (SO 2-/3) ions under various conditions are of high current interest because excessive exposure to sulfite is toxic and the origin of this toxicity seems to involve sulfite oxidative pathways [1]. An important fact is that human exposure to sulfite is on the increase [1,2]. Some of the increase in the sulfite exposure is linked to the fact that SO2 is a major air pollutant [2] and in aqueous media SO2 exists in equilibrium with SO2-/3. In addition, beverages and foods are common sources of sulfite intake. For example, sulfite is used extensively in the wine industry as an inhibitor of yeasts and bacteria and is present in finished wines in concentrations up to 6 mM [1]. Sulfite is also often added to dehydrated fruits, vegetables and soups, as well as fruit juices and beer [1,3,4]. Because of these, the mean daily intake of sulfite from diet (in the United States) has been estimated to be between 0.0014 and 0.14 mM/kg body weight [1]. At such high levels, sulfite exposure can have toxic effects, such as the induction of an acute asthmatic state [5,6]. Sulfite also appears to have adverse genetic effects [7] and can act as a mutagen or comutagen [8] and a cocarcinogen [5,7-9]."

Jan 1, 1990

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By S. P. Sandoval

Several researchers have shown that the surface of chalcopyrite becomes hydrophobic under oxidizing conditions. Because dissolution of copper from chalcopyrite in dump leaching occurs under oxidizing conditions, the U.S. Bureau of Mines studied the effect of surfactants on chalcopyrite leaching under dump chemical conditions. Surfactants were selected for study because they can lower interfacial tension. The tests were conducted in shaking water baths using 250-mL Erlenmeyer flasks in statistical experimental design formats. The addition of nonionic surfactants increased copper extraction in the fernc sulfate leaching of chalcopyrite when sufficient Fe3+ was present. A positive interaction between Fe3l+ concentration and surfactant concentration was demonstrated. Copper concentration in the leachhing solutions was increased by as much as 100 pct at 25° and 50° C by adding nonionic surfactants. ionic surfactants decreased leaching. The structure of the nonionic surfactants and their hydrophile-lipophile balance (HLB) influenced surfactant performance. The branched hydrophile of an ethoxypolyol was beneficial to surfactant performance. The ethoxypolyol was the superior surfactant at 25° C, but became unstable at 50° C. Four surfactants, an ethoxyalchohol and three block copolymers, performed best at 50° C.

Jan 1, 1990

By Jr. Gabler

World resources of cobalt appear ample for the foreseeable future; however, political and economic events have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of cobalt in the economy that would delineate and quantify the production areas where metal values are lost. As a result, the Bureau has developed a computerized commodity flow model. A major attribute of this model is that it is amenable to updating as supply, demand, and/or production data change. This report follows the flow of cobalt through its metallurgical and chemical applications and highlights areas where significant losses occur due to downgrading, export, or disposal. The study indicates that about 4,300,000 lb of cobalt-bearing materials are lost each year, representing 24 pct of U.S. domestic demand.

Jan 1, 1990

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. This report summarizes a more comprehensive minerals report on the Forests prepared by the Bureau of Mines and was written for a general audience without a background in geology or related fields. Mineral resource information indicates that in the Gore Range-the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range.

Jan 1, 1990

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By Cheryl Hill, Michael Keane, Pamela Mike, Raghoottma Pandurangi, William Wallace, Mohindar Seebra, Val Vallyathan

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte bemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz and kaolin dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect of lecithin adsorption. Dust hemolytic potential versus medium pH is presented. Fourier transform infrared spectroscopy and photo-acoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis. INTRODUCTIONQuartz dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction.In the alveolar ·spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, among other functions, mechanically stabilizes the lung from collapse by reducing the surface tension of water in the alveolar sacs.1 This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11 % in dog lavage fluid), and phospholipids (about 88%).2 Pbosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalmitoyl lecithin (DPL).2 Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occurring upon deposition of a particle in a pulmonary alveolus. As may be seen from Figure 1, the DPL molecule has several fixed charges at neutral pH; a positive charge on the trimethylamine (choline) moiety, and a negative charge on the phosphate group. Also evident are the two fatty acid residues of palmitic acid, which are bonded through ester likages to the glycerol segment of the molecule. The fatty acid moieties of phosphatidyl choline make the molecule inso1uble in aqueous solutions under normal conditions, but a colloidal unit of aggregated molecules called a micelle is usually formed spontaneously above a certain minimum concentration. Small micellar vesicles are generally formed in the laboratory by using ultrasonic agitation or by solvent evaporation methods."

Jan 1, 1990