Search Documents

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By N. S. Dalal, J. F. Mega, X. Shi, V. Vallyathan

Several studies have suggested that pulmonary toxicity to asbestos and silica may be mediated through oxidant-induced cell injury. We have reported recently that surface radicals associated with freshly fractured silica may be an imponant factor in cell injury and induction of pulmonary disease. Although the generation of oxygenated radicals in dust-cell interactions has been demonstrated, there are no data correlating the toxicity of a dust with the level of oxygen radical generation by the dust during its interaction with phagocytic cells. In the present study, we have investigated the in vitro generation of oxygen free radicals from human neutrophils and rat alveolar macrophages stimulated with freshly fractured silica, aged silica, amosite, crocidolite, chrysotilc, and a nontoxic dust, barite. Electron spin resonance (ESR) with the aid of a spin trap phenyl-N-ten-butyl nitronc (PBN) was used to measure the oxygen radicals generated during phagocytosis of the dusts. The relative toxicity index and ESR peak heights, on an equal surface area basis and normalized to barite as one, showed a direct relationship. The normalized toxicity indices and peak heights were: silica, 3.5 versus 2; chrysotile, 4 versus 2; crocidolite, 11 versus 8; and amosite, 26 versus 13. Addition of hydroxyl radical scavengers such as catalase, dimethyl sulfoxide, 1,3 dimethyl-2-thiourea (DMTU), sodium benzoate, and mannitol prevented the radical generation. Carmustine, a glutathione reductase- glutathione peroxidase inhibitor, caused a 5-fold increase in the radical generation. These results indicate that a nontoxic dust such as barite generates toxic oxygen radicals at a minimal level that can be quenched by the normal cellular defense system. For toxic dusts such as silica, amositc, chrysotile, and crocidolite, the potential for oxygen radical generation is enhanced by their surface propenies, physical dimensions, and the surface-based radical-generating redox sites. The enhanced radical generation may impair the cellular defense system, resulting in cell injury. Use of scavengers, chelators, and potentiating agents suggests the membrane-based oxidase system as the probable primary source of the radical-generating system. The data presented herein suggest the generation of oxygen free radicals as an important primary event in silica- as well as asbestos-induced cell injury.

Mar 1, 1992

By M. W. Barger, J. K. H. Ma, J. Y. C. Ma, V. Castronova

The objective of this study was to investigate the effects of various bisbenzylisoquinoline (BBIQ) alkaloids on respiratory burst activity of alveolar macrophages and to characterize the interaction of these drugs with alveolar phagocytes. BBIQ alkaloids were chosen for study because they exhibit a wide range of antifibrotic potencies in a rat model, with tetrandrine being very effective and tubocurarine being ineffective. These drugs inhibited zymosan-stimulated oxygen consumption with a potency sequence of tetrandrine (IT) = fangchinoline (FA) > berbamine (BE) ., cepharanthine (CE) "" cycleanine (CY} ~ tubocurarine (TU). This inhibition of respiratory burst activity could not be attributed to a drug-induced decline in the ATP content of these pneumocytes. Drug binding to alveolar macrophages was directly dependent on temperature and drug concentration. The sequence for binding capacity was FA > TT = BE = CY > CE ~ TU. Therefore, there was no simple relationship between binding capacity and inhibitory potency. Binding capacity was not related to lipophilicity of these alkaloids. In addition, tetrandrine failed to bind to metabolically dead cells or sonicated macrophage preparations. These data suggest that the interaction of BBIQ alkaloids with phagocytes is not simply nonspecific binding to membrane lipids. Alteration of the cytoskeletal system with vinblastine, taxol, or cytochalasin B decreased tetrandrine binding by approximately 33% when adtkd separately and by 93% when added jointly. Pre-exposure of alveolar macrophages to stimulants increased the ability of BBIQ alkaloids to inhibit both oxygen consumption and superoxide release. These data suggest that the mechanism by which BBIQ alkaloids inhibit activation of phagocytes involves microtubules and bules and microfilaments. Pre-exposure of macrophages to stimulants would change the conformation of cytoskeletal components and may make these structures more susceptible to drug interaction.

Mar 1, 1992

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

By V. Vallyathan, Xianglin Shi, N. S. Dalai

While Cr(VI) is a known carcinogen, the underlying biochemical mechanism is still not fully understood (1). In a pioneering study Jennette (2) utilized electron spin resonance (ESR) spectroscopy to demonstrate that a long-lived Cr(V) species is generated during the reduction of Cr(VI) by microsomes in the presence of NADPH. Later Wetterhahn and co-workers (3, 4) showed that incubation of chromate with isolated rat liver mitochondria causes the reduction of Cr(VI), as well as the formation of a Cr(V) species. Analogous Cr(V) species have also been detected in the reduction of Cr(VI) by other cellular systems such as Hanserulla polymorphared (5) and blood cells (6, 7). All these as well as other studies (8-12) have suggested that this Cr(V) species plays a significant role in the mechanism of Cr(VI) toxicity. Thus far, however, the chemical structure of this dominant Cr(V) species formed in cellular systems has not been identified, and this observation provided an impetus for the present investigation. Another reason for undertaking this study was that some recent reports (10-16) suggest that hydroxyl ('OH) radicals may also play an important role in the mechanism of Cr(VI) toxicity. In particular, it has been shown that OH radicals are formed in reactions between Cr(V) species and H2O2 (13-16), and that the radical yield depends on the chemical structure of the Cr(V) species (15). For example, while Cr(V)-diol complexes efficiently generate OH radicals, another Cr(V) species, the tetraperoxochromate (CrO3/8) ion, does not (15). Thus in the present study, we focused our attention on the following: (a) structural identification of the Cr(V) species generated in the reduction of Cr(VI) by subcellular as well as cellular systems, using microsomes, mitochondria, and Escherichia coli; (b) possible detection of OH radical in the same systems since there is no earlier report of chromium-mediated generation of 'OH radicals in a cellular system; (c) possible involvement of molecular oxygen in chromium-related OH radical generation since a recent report (17) indicated that Cr(VI) mutagenesis is strongly oxygen dependent; and (d) elucidation of the mechanism of OH radical formation in these systems.

Mar 1, 1992

By M. S. Seehra, R. S. Pandurangi

"The interaction of amorphous silica particles with several hydrogen bonding agents (H2O,, C2H,OH, C,H,NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy, It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction of surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C,H,NO > C2H2OH > H2O.The use of IR spectroscopy to study the adsorption on solid surfaces is well documented in the literature,"" For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1. Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-6 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity,7-9 catalysis,10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated-have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8N0), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by IR spectroscopy, and Knozinger16 and Rouxlet and Semples17 have used transmission IR spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties, In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18,19 Moreover, according to a recent paper,20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry, In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H5OH, and H20) with the silica surface by monitoring changes in the surface IR modes, Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents, Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16,17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification, Details of this work are given below,The Cab-O-Sil samples of silica used here were obtained from the Cabot Corporation of Tuscola, IL, In our earlier studies,14,20 we have shown these particles to be amorphous and about 0.05 am in size, For coverage of these particles with H20 and C2H50H, the following procedure was employed. About 5 mg of silica was mixed with 50 mL of the liquid (H2O or C2H5OH) and refluxed for one hour, The remaining liquid was allowed to evap¬orate to dryness and 1 mg of the treated sample was used to collect the PA spectra. In the case of PVPNO, the amount that binds to Cab-O-Sil is taken from the data on quar"

Mar 1, 1992

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992

By R. L. Grayson, W. E. Wallace, T. Simonyi, J. C. Harrison

"Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz may have different amounts of surface-availablequartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface-available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.INTRODUCTIONFrom our previous work (Grayson, 1991), we have shown that the amount of pure quartz in a respirable coal mine dust sample appears to vary directly with the rank of the seam (using fixed carbon as the basis for comparison), except when a substantial rock parting, roof or floor are mined. Our other work (Wallace et al., 1989) showed that high-silica particles in a clay mine may generally be coated with clay, rendering the quartz core non-available for surface reaction in the lung. The combination of these findings led us to hypothesize that the coating phenomenon may indeed be present in coal mines as well, and that a rank relationship may be present regarding this phenomenon. Thus higher rank coal seams may have more surface-available quartz as well as more pure quartz particles in their respirable dusts. The scientific protocol for testing this hypothesis and the results obtained to date are discussed in this paper. Thus far, there is no reason to doubt that the relationship holds."

Mar 1, 1992

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By R. Hogg, E. Kaya

"The presence of agglomerated particles in airborne dust in coal mines has been confirmed by SEM examination of static samples collected on substrates. In addition, the effect of agglomerated particles on the performance of cascade impactors and cyclone-type personal samplers has been studied. Simple procedures have been developed for evaluating the extent of agglomeration in air-borne dust by comparing the observed size-selectivity of the sampling devices with that expected under idealized conditions. Applications of these techniques in the laboratory and in underground mines are discussed.INTRODUCTIONAirborne dust is invariably present in mine atmospheres. Particle size is a primary factor in determining the behavior of the dust, its effects on miners' health and the effectiveness of dust control measures. Obviously, agglomeration of the dust particles can have important effects on: ""natural"" dust removal processes such as settling• the use of water sprays etc., for dust control• pulmonary deposition characteristicsIn addition, the presence of agglomerates could influence the effective toxicity of the dust. For example, ultrafine particles are often thought to be relatively unimportant in the development of respiratory ailments because of their low deposition efficiency. However, the latter could be substantially increased if such particles were present in larger agglomerates. It is by no means obvious that there should be significant agglomeration of the airborne dust in a mine atmosphere. In fact, calculations based on the classical coagulation theories indicate that, at the kinds of dust concentrations that exist even in what would be regarded as “very dusty"" atmospheres, the coagulation half-time* .should be of the order of weeks or even months. On this basis, agglomeration would be expected to be essentially negligible. On the other hand, laboratory experiments (Polat et al., 1991) have revealed very extensive agglomeration in the airborne dust released during the crushing of individual coal and mineral particles. It is postulated that such agglomeration occurs immediately at the point of dust generation. In other words, many of the fine fragments produced on fracture are never completely separated from their neighbors."

Mar 1, 1992

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By C. P. Fang, V. A. Marple, K. L. Rubow

"Studies of the flow fields and particle impaction characteristics are more complicated in multi-nozzle impactors than in single-nozzle impactors, since the jets of air must penetrate cross-flowing air to impinge on the impaction plate. Results of heat and mass transfer analysis are employed to describe the cross-flow pattern in multi-nozzle impactors. A cross-flow parameter has been derived to predict the deflection of the air jet by the cross-flow. This parameter is expressed as a function of the geometric parameters for the multi-nozzle impactor. DnN 4D,, where N is the number of nozzles, Dn the nozzle diameter and D, the nozzle cluster diameter. Empirical particle collection data show that multi-nozzle impactors operate satisfactorily, if the cross-flow parameter is less than a critical value of 1.2. Impactors operating with a cross-flow parameter larger than this critical value are shown to possess poor particle collection characteristics.Inertial impactors of many designs have been used for sampling aerosol particles. Impactors can be single stage, consisting of a nozzle and an impaction plate, or a cascade impactor with several stages in series. The simplest design for a stage is a single nozzle with a flat impaction plate. However, many designs use stages with multiple nozzles of identical size, which allows for compact impactors to be designed at rather substantial flow rates and moderate pressure drops.Nearly all of the theoretical work, and much of the experimental work, has been performed on single-nozzle impactors. The results of single-nozzle impactor analysis are often applied to multiple-nozzle impactors, which are assumed to be a group of individual nozzles, each operating as though they were single nozzles. However, an important fact is often ignored: the interaction of flow from adjacent nozzles can change not only the fluid mechanics in the impaction region, but also the locations of the jet stagnation points, and the impaction characteristics of each nozzle.The effect of multiple nozzles on the particle collection characteristics of impactors has been studied by a few investigators. May (1964), Fletch et al. (1967), Friedrichs (1968), and Vaughan (1986) reported that the quantity of particles in deposits of nozzles in the first two stages of the Andersen multi-nozzle cascade impactor were not equal. The inner deposits appeared to contain fewer particles than the outer ones. However, Vaughan (1986) in addition showed that many of the deposits in the outer three rows were missing on the first stage, even though the outer deposits that were present were larger than the inner deposits.May (1964) conducted experiments and explained the phenomenon of smaller deposits near the center than near the edge. He noted that in Andersen cascade impactors the air issuing from the nozzles moves radially outward along the narrow channel between the nozzle plate and the impaction plate. This flow at 28.31min -1 created a pressure difference of about 1 mm water between the inner and outer sections of the channel. The effect was most pronounced in the first two stages, where the pressure drop across the nozzles was also about 1 mm water. Here, the flow velocities in the nozzles, and hence the deposits, were smallest at the center and increased toward the periphery of the impaction plate. since the pressure drop across the nozzles was the smallest at the center and a maximum at the periphery. This effect was negligible in the lower stages because of a larger pressure drop across the nozzles. According to May (1964), this effect could be eliminated by increasing the nozzle-to-impaction-plate distance to three nozzle diameters and improving the nozzle arrangement to allow air flow to escape to the periphery more easily."

Mar 1, 1992

By E. V. Cilento, R. C. Laotz, K. A. DiGregorio

"PULMONARY ALVEOLAR macrophages (PAM) protect the lungs by providing a first line of defense against inhaled foreign debris and bacteria. In this role PAM phagocytize foreign matter, secrete enzymes that augment microbial killing and digestion, and produce reactive oxygen me-tabolites (2, 3, 18, 19, 22, 26). However, in addition to this antibacterial function, PAM participate in a diversity of functions, such as tissue repair, lipoprotein metabolism, and immunoregulatory activities (11, 22).Studies have suggested the existence of a heterogeneous population of PAM with respect to immunologic function, enzyme release, phagocytosis, morphological characteristics, expression of membrane receptors, ad-herence, and superoxide (O2•) release (4-7, 10, 16, 21, 23, 28). This heterogeneity has been observed by analyz¬ing subfractions of PAM separated by cell density frac-tionation. For example, using guinea pig PAM, Dauber et al. (7) showed heterogeneity in cell density and size, morphological characteristics, and cytochemical properties, whereas Holian and co-workers (16) reported variations in migration, chemotaxis, O2• release, and pinocytosis among subfractions collected. Similarly, O'Neill et al. (21) observed functional heterogeneity in rat PAM with regard to phagocytosis, O2 • release, and lysosomal enzyme activity.Several investigations have reported a correlation between PAM activity and cell volume. Most studies have shown that O2 release from PAM increased with decreasing cell size (15, 21, 25), although Bielefeldt Ohmann and Babiuk (4) reported a decreasing trend. However, Gallin (13) has suggested that significant variability may even exist within density-defined or cell-volume subfractions that could lead to misinterpretation of results concerning PAM heterogeneity.A better understanding of the heterogeneity in O2 production may be obtained by using single cell meas-urements to evaluate whether functionally distinct sub-populations actually do exist. As such, the present study was designed to examine heterogeneity in O2 • release from single PAM using a recently developed electrooptical technique (8). The initial oxygen metabolite, O2•, produced by NADPH oxidase at the surface of the plasma membrane, was measured by quantifying the reduction of nitro blue tetrazolium (NBT I to a diformazan precipitate. Measurements were made from video recordings of individual cells stimulated by their adherence to the bottom of a culture dish. The cell volume and degree of spreading also were determined directly from the same video recordings, and the data were correlated with the initial rate and maximum amount of diformazan produced by the same cell."

Mar 1, 1992

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

"Correlatina Lung Crackle Usina Holographic lnterf erometryAli Afshari, MS, West Virginia University, 1989The Effect or Surfactants on Suppression of Non-Wettable ParticlesAli Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989Geochemical Characterization of Kerogem, ShaJes, and Coal .Refme ~ted with Allegheny Fonnationof Cases of Northern West VirginiaDick Andre, MS, West Virginia University, 1987Particle Concentrations in a Hazelton Inhalation ChamberShahram Bavani, MS, West Virginia University, 1985Use and Potential of Luer Holographic Interferometry and Subsidence Model Study of an Underground.Room and Pillar MineRichard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall MineRichard Begley, PhD, West Virginia University, 1990.Redesign of Micro-Orifice Unifonn Deposit ImpactorSteve Behm, MS, University of Minnesota, 1991A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine FragmentFonnationZ. T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University,University Park, PA. Final Report, October 1, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine AtmospheresR. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental StudiesR. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987Experimental Studies of Dispersion and Deposition of Fane Particles in a Wind Tunnel and Mine AirwayKlaus Bode, MS, Mining Engineering, The Pennsylvania State University, 1991Perf'onnance of the High Yield Technology PM - 100 - Particle 11ux MonitorRobert Caldow, MS, University of Minnesota, 1987Development of Improved Methods for Monitoring and Control of Diesel Particulate in an Underground CoalMineD. H. Carlson, B. C. Cornilsen, P. L. Loyselk, X. Shan and J. H. Johnson, Michigan Technological University,Houghton, Ml. Final Report, June 15, 1991"

Mar 1, 1992

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By N. S. Dalal, Xianglin Shi

"The mechanism of vanadium(V) V ) toxicity is still not fully understood in spite of extensive current effort (1-3). The presence of a vanadium(V) V ) -dependent NAD ( P )H oxidase in cell membranes suggests that at least one of the pathways involves oxidation of NAD(P)H (1-3). Considerable effort has therefore been devoted to finding the mechanism of NAD ( P ) H-oxidation by va¬nadium( V ) (1-19). Recently Liochev and Fridovich (4, 16) provided a critical review of vanadium( V) -stimulated NAD (P )H oxidation by plasma membranes. They out¬lined a mechanism in which vanadium(V) V )-stimulated oxidation of NAD ( P )H by biomembranes involves an O2 - initiated free radical chain reaction (4 ). While the above may be the major pathway for the vanadium-me¬diated NAD (P )H oxidation in membrane-related sys¬tems, some recent results suggest that in the presence of NADPH the flavoenzyme glutathione reductase can function as a vanadium(V) V ) reductase (18). Because of the significance of this result in relationship to the mech¬anism of vanadium( V) metabolism and the novelty of the metal-reductase behavior of a flavoenzyme, we have car¬ried out additional studies on one-electron reduction of vanadium( V) by two other, related flavoenzymes: lipoyl dehydrogenase and ferredoxin-NADPH oxidoreductase. These two enzymes were selected because they are known to catalyze a one-electron reduction of Cr ( VI ) (19-21 ), which is isoelectronic with vanadium( V ).The present study also reports on the generation of hydroxyl ( • OH) radicals in the vanadium( V) -flavoen-zyme redox system without exogenous H2O2. The • OH study was undertaken because • OH radicals are known to be generated in reactions of vanadium( IV) with H2O2 (17,18,22-27). For example, Piette and co-workers (17, 22) have studied effects of vanadium(IV) IV ) on lipid per-oxidation and NADPH oxidation and suggested that va-nadium( IV) -induced • OH radical formation may play an important role in vanadium( V) toxicity. Carmichael (25, 26) investigated the reaction between a RNA /VO 2' complex and H2O2 with a view to probe the possible re-lationship between vanadium( IV) -mediated • OH radical generation and DNA damage. He has suggested that in this reaction the • OH radical adds to the C (5) carbon of uracil, causing nucleotide damage, similar to what occurs in the nucleotide /Fe2+ / H2O2 reaction (28) and in y-irradiated aqueous solutions of nucleic acids (29 ). To our knowledge, however, there is as yet no report on ·OH radical generation in any reaction involving the reduction of vanadium ( V) by a well-characterized enzyme, without exogenous H20 2 • The present study provides evidence that ·OH radicals can form in a flavoenzyme-mediated reduction of vanadium( V) to vanadium( IV) and that this process involves also the reduction of molecular oxygen ( 0 2 ) to H20 2 • The H20 2 thus generated reacts with vanadium( IV) to produce ·OH radical, in analogy with the Fenton reaction ( Fe2 + + H20 2 - Fe3 + + OH- + ·OH)."

Mar 1, 1992

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992