Search Documents

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

By Welby G. Courtney

This publication reviews recent U.S. Bureau of Mines studies of frictional ignition of a methane-air environment by coal mining bits cutting into sandstone and the effectiveness of remedial techniques to reduce the likelihood of frictional ignition. Frictional ignition with a mining bit always involves a worn bit having a wear flat on the tip of the bit. The worn bit forms hot spots on the surface of the sandstone because of frictional abrasion. The hot spots then can ignite the methane-air environment. A small wear flat forms a small hot spot, which does not give ignition, while a large wear flat forms a large hot spot, which gives ignition. The likelihood of frictional ignition can be somewhat reduced by using a mushroom-shaped tungsten-carbide bit tip on the mining bit and by increasing the bit clearance angle; it can be significantly reduced by using a water spray nozzle in back of each bit, which is carefully oriented to direct the water spray onto the sandstone surface directly behind the bit and thereby cool the hot spots formed by the worn bit. A bit replacement schedule must be used to avoid the formation of a dangerously worn bit.

Jan 1, 1990

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

Measure tattling in cemented backfill when installation of bore-hole extensometers is not feasible. Problem To evaluate the amount of load that backfill carries during pillar recovery, information about how much the backfill settles after placement is often required. However, the composition of some backfills makes them difficult to drill and the installation of borehole extensometers almost impossible. Approach Bureau researchers have developed a vertical fill extensometer that can be cast in place as a stope is being filled. It consists of a baseplate, sections of steel pipe enclosed in loosely coupled polyvinyl chloride (PVC) pipe, and a top anchor assembly that contains a displacement transducer (fig. 1).

Jan 1, 1990

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By Richard J. Mainiero

The U.S. Bureau of Mines in cooperation with Jim Walter Resources, Inc. (JWR), Brookwood, AL, evaluated the use of sheathed explosive charges in breaking up large stones that can jam the feeder¬breaker or pan conveyor on longwalls and halt operations. Use of the sheathed charge reduced the downtime of the longwall panel to 15 to 30 min as compared with the 1 to 2 h required to drill and shoot the stone. Firing the sheathed charge at the face caused no significant damage to Iongwall equipment. Use of the sheathed charge also represented an improvement in safety by eliminating the exposure of miners to the inherent hazards of the face for extended periods of time. Another benefit, which is difficult to quantify, is the elimination of the temptation to shoot mudcaps or adobes, which is illegal in U.S. underground coal mines.

Jan 1, 1990

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) measurements provide direct evidence for the involvement of Cr(V) in the reduction of Cr(VI)· by NAD(P)H. Addition of hydrogen peroxide (H2 O 2) to NAD(P)H-Cr(VI) reaction mixtures suppresses the Cr(V) signal and generates hydroxyl (·OH) radicals (as detected via spin trapping), suggesting that Cr(V) reacts with H2O 2 to generate the ·OH radicals. Reaction between H2O 2 and a Cr(V)·glutathione complex, and between H2O 2 and several Cr(V)-carboxylato complexes also produces ·OH radicals. These results suggest that Cr(V) complexes catalyze the generation of ·OH radicals from H2O 2, and that ·OH radicals might play a significant role in the mechanism of Cr(VI) cytotoxicity. KEY WORDS: ESR. spin trapping, Cr(VI) reduction, Cr(V), hydrogen peroxide, free radicals.INTRODUCTIONThis communication reports an ESR spin trapping detection of hydroxyl ( OH) radicals.in reactions between some Cr(V) complexes containing biologically important ligands and hydrogen peroxide (H2O 2 ). This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step in the mechanism of Cr(VI) toxicity, the reaction· mechanism is not yet clear. 1 Mutagencity has been well documented for Cr(VI) via various bacterial assays, while Cr(III) has been shown not to be mutagenic.2 • 3 Since it has been reported that compounds containing Cr(VI) do not react with isolated DNA,4 the reduction of Cr(VI) by other cellular constituents has been thought to be important in the mechanism of Cr(VI) induced DNA alteration.1·4 • 5 For cellular systems earlier studies include those on the reduction of C~(VI) by microsomes,6-8 rat liver DT-diaphorase,9 and aldehyde oxidase. 10 Regarding the reduction mechanism, Jennette used ESR spectroscopy to show that a long-lived Cr(V) complex is formed as an intermediate in the microsomal reduction of Cr(VI) in the presence of NADPH.8 She postulated that Cr(V) is the ""ultimate"" carcinogenic form of chromium compounds. This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions.11 - 19 More recently, however, it has been suggested that oxygen-derived radicals generated during the Cr(VI) reduction are the species responsible for the DNA alteration.20.2• To the best of our knowledge, however, no information is available on the generation of such radicals in the reduction of Cr(VI) under biologically relevant conditions, except some preliminary results on the glutathionyl (GS·) radical formation in the reduction of Cr(VI) by glutathione (GSH). 11 - 19 We, therefore, undertook a systematic investigation of the reaction of Cr(VI) with NAD(P)H, GSH, ix-hydroxycarboxylic acids, and H2O 2 • NADPH was chosen as a model reductant because of its ubiquitous existence inside the cells, its critical role in the enzymatic Cr(VI) reduction,1·6-9 its representation of important cellular Cr(VI) reductants, and its ability to reduce other metal ions.22 GSH was chosen as another model Cr(VI) reductant because GSH also exists inside cells, it represents another important category of cellular Cr(VI) reductants, the thiols, and it also plays an important role in the Cr(VI) toxicity .1• 1 ""- 19.i3.i4 For further clarification, we also studied the reaction of Cr(VI) with several '1'.-hydroxycarboxylic acids in the presence of H2O 2 since these acids are definitively known to reduce Cr(VJ) to form stable, isolable Cr(V).25 .2 6 The results obtained indicate that Cr(V) complexes, produced in the reduction of Cr(VJ) by cellular reductants, react with H2 O 2 to generate ·OH radicals, which might be the initiators of primary events in Cr(VI) carcinogenicity."

Jan 1, 1990

Develop personal computer (PC) based software for analyzing and/or filtering time- and frequency-domain attributes of seismic and electromagnetic signals from geophysical surveys for the enhanced interpretation of rock masses and subsurface geologic structure. The Problem Both mining and petroleum geophysicists utilize seismic signals to characterize rock masses for delineating subsurface stratigraphy and structural conditions. However, a vast amount of information available in seismic project evaluation data often is unavailable for interpretation unless these data are enhanced. New processing technology increases the quality of these signals for analysis and interpretation. Comprehensive signal processing software is mostly written for petroleum exploration companies. Commercially available signal processing programs are often limited to a single application or are restricted for use with specific hardware, e.g., a digital oscilloscope or a mainframe computer. The programs may use computer codes that are proprietary, restrict user modification to expand capabilities, or may be hard to interface. They may have insufficient documentation for easy use and be support dependent.

Jan 1, 1990

By Joseph Gersic

In 1989-90, the Bureau of Mines appraised selected high resource potential areas containing gold, rare-earth-element, or pegmatite deposits in or near the Black Hills National Forest. Available mineral resource data were used to construct mine and mill models and to compute discounted cash-flow rate-of-return analyses. Using this information, the economic feasibility of possible operations and probability (in the nonmathematical sense) of exploration and development within the next decade were assessed. High exploration and development probabilities are forecast for gold deposits around existing and permitted mine areas near Lead-Deadwood and west of Galena. The area east of Galena has low to moderate exploration and development probability; the Rochford area has low to high exploration probability and low to moderate development probability; the Keystone area has low to moderate exploration probability and low development probability; the Medicine Mountain area has moderate to high exploration and low to moderate development probabilities. Exploration probability in the Bear Lodge Mountains area is high for rare-earth elements and gold; development probability is low. Exploration probability for gold in the Mineral Hill area is low to moderate; development probability is low. The current level of activity associated with pegmatite mining in the Black Hills would probably not change significantly in the next decade; both exploration and development probabilities are low to moderate.

Jan 1, 1990

By S. P. Signer

The Bureau of Mines conducted a series of field tests to improve the understanding of the support interaction mechanics between fully grouted bolts and coal mine roofs and to help lay the foundation for improved design and evaluation techniques. Strain gauges were installed on 14 fully grouted bolts placed in shale roof rock at four mines in Colorado, Illinois, and Pennsylvania to determine how load was transferred between the bolts and the rock. The results of field tests on elastic bolt behavior compared well with previous laboratory work and numerical models. The field tests showed that the anchorage length of grouted bolts installed in shale was slightly longer than the anchorage length determined in laboratory tests conducted in concrete blocks. The field results produced more variability because of geological variations. Tests run past the yield point of the steel bolt indicate that the yield zone varies significantly and translates down the length of the bolt anywhere from 4 to 22 in.

Jan 1, 1990

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

INPUT FORMAT INSTRUCTION FILE FOR PROGRAM MFIRE GENERAL RULES FOR DATA INPUT: $THERE IS NO NEED TO DISTINGUISH INTERGER AND REAL NUMBERS. $ $ SYMBOLS FOR NUMERICAL INPUT INCLUDE THE FOLLOWING $ $ 1234567890 -+BLANK $ $ * FREE FORMAT IS ALLOWED. COMMA AND BLANK SPACE CAN BOTH BE $ $ DELIMITERS. SEQUENTIALLY DISTRIBUTED BLANK SPACES ACT AS ONE $ $ DELIMITER. BLANKS ADJACENT TO A COMMA HAVE NO DELIMITING EFFECT $ $ * A ZERO INPUT CAN BE OMITTED BUT NOT THE DELIMITERS EXCEPT WHEN $ $ THE ZERO INPUTS ARE THE LAST ONES ON A LINE. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS "$ IS AN INSTRUCTION $ $ LINE WHICH WILL BE IGNORED IN A PROGRAM RUN. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS NEITHER ONE USED IN THE $ $ ABOVE LIST FOR NUMERICAL INPUT NOR "$, OR WHICH CONTAINS MORE $ $ THAN 3 SYMBOLS OUTSIDE OF THE LIST, IS A COMMENT LINE WHICH WILL $ $ BE SHOWN IN THE OUTPUT FILE. $

Jan 1, 1990

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The usual run time errors occur when illegal mathematical operations are attempted by MFIRE For exam¬ple, if the user enters a negative value for the input variable HEAT to model a heat sink or cooling station, a run tame error will occur because an exponential function is employed to better model the changing temperature dis¬tribution in the airways. DATA FILE ERRORS Two types of data file errors can occur. 1 An error may occur because the input data file itself is invalid This may be caused by: The data file cannot be found due to incorrect spelling, drive, or path specification Check the spelling and path at the prompt for location of the data file. The data file contains non-ASCII symbols Check op¬eration of the text processor to insure that only ASCII characters are produced Delete all non-ASCII and/or all out of place characters. 2 Data are accepted by the program, but are incorrect for the data types or ranges or the combination causes a data inconsistency This may be due to. An invalid character is located where a numerical value is required The input data value is outside the reasonable range The input data is insufficient to build the model for simulation. The input data exceeds the capacity of the program. PROGRAM ERROR DETECTION When the program is running, tracing messages are given on the screen indicating the group and lines of data that have been read and the section of the program that is executing Program termination indicates that problems are caused by the subsequent (not read) data file section. For each detected error, descriptive message starting with * ERROR * is issued and the program terminates. When a possibly wrong value and/or its calculated intermediate result is detected, a descriptive message starting with * WARNING * is issued and the program continues. If a modification of input value or calculated intermediate result is automatically made by the program, descrip¬tive message starting with * ATTENTION * is issued and the program continues. LOCATING ERRORS If a message indicates that the error condition occurred due to the data input file, locate and correct the data item. If no error message is issued, but the simulation results are not as expected, carefully check the list of input data shown in the output file WARNING messages and ATTENTION messages may reveal an error in the input data even though the program continues to operate Insure that the default values or modifications adopted by the program run are acceptable. Anomalistic data, though not incorrect or impossible, may lead to an unusual simulation For example, making a fan unusually powerful may prevent a normal strength fire from affecting the airflow distribution in the system Much care must be employed before considering an ex¬treme case. If a message indicates that the accuracy criterion in the temperature section of the program was not satisfied, a table detailing the current parameters of airways which have large fluctuation in the average air temperature from iteration to iteration is produced If the pattern of the parameters is clearly cyclical, while the variation of natural ventilation pressure is stable or cyclical from iteration to iteration, then, most likely there is no single equilibrium stage for the event If the variation of natural ventilation pressure decreases steadily though slowly, increasing the value of data item variables MADJ or ITN (on control line number 1) may allow convergence.

Jan 1, 1990