Search Documents

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. ' In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

"Let us not think of our departed dead As caught and cumbered in these graves of earth; But think of death as of another birth, As a new Freedom for the wings outspread, A new adventure waiting on ahead, As a new joy of more ethereal mirth, As a new world with friends of nobler worth, Where all may taste a more immortal bread." FLOYD W. PARSONS N. CHRISTENSEN JOSEPH F. PETERS GEORGE B. PARKER ROBERT WILLIAMS B. F. DEVINNY

Jan 1, 1942

By W. F. Murray

Coal mining as an occupation, is hazardous under the most, ideal conditions. Confronted with this inescapable fact, every possible emphasis is placed by the Phelps Dodge Corporation, at the Dawson mines upon the employment of every means available for safeguarding its employes from the dangers attending their vocation. Accidents have a human aspect and a direct bearing upon the well-being of the workmen themselves. They cause a loss of wages, suffering and often privation of the employe and those dependent upon him. In case of death, his children are often forced into the wage earning class without preparation to fight the battles of life, with the result that the efficiency of the next generation is lowered. Dr. Jones, formerly of the war industries board, is responsible for the following statement. "Accident prevention as it is now conducted is principally a matter of education and not merely one of protection against physical hazards as frequently believed. In fact, the last ten years experience in accident prevention has demonstrated conclusively two things: 1. That three-fourths of all deaths and serious injuries in industry can be prevented. 2. In the industries doing the most efficient work, two-thirds have been accomplished thru organization and education as against one-third accomplished by means of mechanical safeguards or equipment. Experience in the past decade has conclusively proven that the work of accident prevention is not a "one man job" that satisfactory results can be secured only thru the highest measure of co-operation between the employer and employe, and this by means of organization. The employer must be vitally interested in the work if he expects to educate his men to share the responsibility with him. The men must be given a part to perform in it, if their interest is to be aroused and maintained. It is only thru organization that this is possible. In this connection it is interesting to note the results obtained by the Old Dominion Co. of Globe, Ariz., in reducing accidents after the organization of their safety department. The O. D. Co. are pioneers in the adoption of the workmens safety committees and and the results obtained by this, company after their safety work was well organized are truly wonderful. For the years 1913 to 1916, inclusive, at which time the safety work was not well organized, there were a total of 18 fatal accidents, the years 1917 to 1920, inclusive, was a period of intensive safety work, during which time there were only three fatal accidents, none having occured during 1919.

Jan 1, 1922

By F. C. Miller

The Colorado Fuel and Iron Company has divided their coal mines into groups or divisions: Las Animas, Huerfano, Fremont and Gunnison counties. Each division is represented by a safety committee composed of three men appointed by the management and three men selected by the employes? representatives. The three men appointed by the management are usually from a group engaged in routine work that is primarily of a safety nature. Mr. Robert McAllister, chief mine inspector; Mr. George B. Parker, superintendent of first aid and mine rescue training; Mr. F. C. Miller, chief chemist, fuel department; and Mr. 0. C. Irwin, assistant chief electrician. The three men appointed by the management act in each of the four divisions. It is the duty of the safety commit- tee to visit each mine three times per year and make a thorough investigation of conditions underground and on top. Their report is in the form of recommendations to the management for their consideration. They are also called to investigate all fatal accidents and learn, if possible, the cause leading up to the accident and recommend precautionary measures that will prevent the recurrence. This committee inspects the haulage roads, air courses, manways, electrical equipment, ventilation, timbering, working places and humidity. In addition, each mine has a local safety committee with the superintendent acting as chairman. It is the duty of this committee to keep in daily touch with conditions underground and on top. They hold weekly meetings and discuss problems related to safety. These men work on local conditions that govern their affairs. As an example: One of the mines has a checking out board at the man-trip parting in addition to the regular checking in and out system as required by law, and this board is checked before the man-trip leaves for the outside, giving the officials a chance to take prompt action in looking up a man who may have become ill or injured. Should a man walk out and forget to check off, there is a penalty imposed. The ventilation of a coal mine is most important and the method of conducting the air to the working face is one of the greatest precautionary measures linked with safety. A quantity of air must be maintained at every working face to insure rapid diffusion of explosive or noxious gases and in a manner without interruption. With this intent in, view, the Colorado Fuel and Iron Company is installing fan equipments with capacities of 200,000 cubic feet per minute with dual drives, twin fans in some instances, for insured circulation. Dual drives consist of a steam engine using exhaust

Jan 1, 1925

PRESIDENT LITTLEJOHN: Before we open the discussion on the Utah mining laws, I want to bring out what I consider a slight misunderstanding on some of the things that I said this forenoon relative to our comparison of accidents. I did not mean to infer that we, as mine officials, are satisfied we have done the best we can to eliminate the accidents, when I was talking about a four-to- one comparison. I do not want any- one to get the idea in their heads that I do not think we are doing all we can. There is not any of us who can state that, even if we better these figures. It is the general understanding that these figures are based upon ratios per thousand man shifts and not upon the tonnage basis that we use. If it were based upon a tonnage basis, I think the figures would be pretty nearly reversed, for we are producing from two to four tons more per man than they do in Great Britain. The discussion will now be continued as I said this morning. There is a gentleman in the audience here that is as guilty of making these laws as I was, and I am quite sure when speaking he will confine himself to the subject of Utah Mining Laws and the prospective results. Before Mr. Monay starts with his paper, I want it understood that this discussion must be finished by 2:30 for the reason that we have still quite a lot of business before us this afternoon.

Jan 1, 1925

By R. Dawson Hall

R. DAWSON HALL (The Coal Age, New York City) : Mr. Chairman and gentlemen: I do not feel that I have anything in particular to say. I have not prepared anything for an occasion such as this. I just came from New York City, and as one man said to me today, "That is not any recommendation in particular." (Laughter.) In answer to your request for a few remarks of a timely character I would say: One of the possibilities in the Rocky Mountain Region coal mines is the use of steel arches, posts and straps. The timber of the region seems unusually subject to dry rot and does not last long, especially in those places as in southern Wyoming, where the mine atmosphere is likely to contain a large quantity of carbon dioxide. It is true that, in many mines, much care is taken to drive out this gas and to arrange that the timber will have the fresh air that will prolong its life, but despite such provision much timber is subjected to speedy rot. Steel has made rapid progress in England, Germany and France and is recognized as an economy, not an extravagance. Frequent replacement of rotting wood and removal of broken rock are a source of great waste, risk and inconvenience in operation that together spell great cost. The very dryness of the mines and the lack' of acid water are favorable to the use of steel where support of roof or sides is necessary.

Jan 1, 1932

By J. J. Forbes

Gentlemen : It is a pleasure to come to Glen- wood Springs to participate in this meeting of the Rocky Mountain Coal Mining Institute an organization created to handle chiefly the economic questions dealing with the coal industry of the Rocky Mountain District. I am not unmindful of the many and varied problems confronting the mining industry of this country which is so general at the present time throughout the United States. By reason of the difficulties experienced in marketing the product of your mines, there is all the more reason for greater economy and efficiency in production. No industry can be efficiently operated without giving due consideration to the safety of the employees. Safety and efficiency are inseparable for the success of any industrial enterprise. While the Bituminous coal companies of the United States are doing splendid work in the promotion of safety, yet our fatality rate is exceedingly higher compared with that of foreign countries, and with greater cooperative organized effort on the part of mine owners, mine officials, mine workers, and state and federal governmental agencies having jurisdiction, much more substantial progress can be made in the future and a greater economic saving .to the industry effected, not taking into consideration the greatest and most important phase of safety, which is the conservation of life and health of all those who are engaged in the occupation of mining. You are concerned with freight rates, marketing of coal and similar operating problems. Yet have you earnestly considered the vital question that plays so important a part toward the success of any mill-

Jan 1, 1926

The Forty-Sixth Meeting of the Rocky Mountain Coal Mining institute convened at the Hotel Colorado, Glenwood Springs, Colorado, June 19, 1950, at 10:00 a. m., G. E. Sorenson, President, presiding. PRESIDENT SORENSON: The meeting will come to order, gentlemen. I note from the program here this morning that you were supposed to have an address by the president. I can assure you, gentlemen, that the president is not going to make an address, so you don't need to squirm in your chairs. I do want to say it's certainly a pleasure to be here. I am sorry that I wasn't here last year. Apparently my absence lent consent, and I think it would be a good warning to every member of the organization to be here for all the meetings for your own protection! It's always a pleasure to be here and meet again with some of our old friends and meet a lot of new ones. It always interests me at these meetings to meet with the rugged individuals that operate the coal industry. They have to be rugged; they couldn't be any other type of men and live in it. I also know that it takes a good rugged man to fight this game nowadays. I feel that the men who operate the coal industry are fighting a battle against socialism. You all know we are the first industry they have their eyes on. If they take over our industry, they will take over everything else.

Jan 1, 1950

Disclaimer ?You may hear something today that surprises you. If you are pregnant or have a heart condition, you may elect to stop hearing now. ?Some of what you are about to hear you may already know. ?Much of what you are about to hear and see is information that is from and can be found via other sources. ?If any of my statements during the course of this presentation are thought or found to be incorrect, I am not responsible for these comments.

Jan 1, 2006

PRESIDENT WETZEL: The meeting will come to order. We are pleased to see a few of the more hardy survived last night's-ordeal and are present this morning. The Secretary has some correspondence which he will read. SECRETARY WHITESIDE: Gentlemen, I have a couple of telegrams and a letter which I would like to read to you at this time. First, a telegram addressed to Mr. Wetzel: "Regret greatly necessity canceling my plans to be present at meeting. Appreciate your conveying my best wishes to members for successful and profitable session.

Jan 1, 1942

Business meeting was opened at 9:30 a.m., June 28, 1967. President James Westfield asked that the meeting come to order. "We have some business to be taken care of this morning. First, we will have a report from the Auditing Committee." Mr. W. S. Landers read the report and said that it had been audited and approved and the motion was made and seconded that it be accepted. It was accepted unanimously. (See Index for Treasurer's Report.) The Resolutions Committee Report was read by Mr. Cliff Artis as follows:

Jan 1, 1967

At the meeting of the American Institute of Mining and Metallurgical Engineers, G. S. Rice, Chief Mining Engineer of the U. S. Bureau of Mines, announced the definition of a gassy mine. This definition has been awaited with much interest, especially by the Safety Committee of the Rocky Mountain Coal Mining Institute. It applies to the whole area of all mines, any part of which is on the public domain of the United States. Consequently it will be of wide application in the western part of this country. The safety committee of the R. M. C. M. I. has been hopeful that the Institute would adopt this definition without exception as the codes of rules to be recommended at all mines in the Rocky Mountain area. The statement follows: "The U. S. Bureau of Mines believes that all coal mines are potentially gassy; but for purposes of administration in respect to prevention of explosions and fires, the Bureau recommends the following classification: "Class 1 coal mine-A practically non-gassy mine in which flammable gas in excess of 0.05 per cent cannot be found by systematic search. "Class 2. coal mine-A slightly gassy mine in which (a) flammable gas has been found, ? but in quantity less than two per cent in still air in any active or unsealed-abandoned workings; or (b) flammable gas can be found, but in quantity less than four per cent, in some place from which the ventilating current has been shut off for a period of one hour; or (c) flammable gas can be found,* but in quantity less than one-fourth per cent in a split** of the ventilating current; or (d) flamamble gas is found in quantity greater than' specified rate*** of not more than 25 cu. ft. per minute. "Class 3 coal mine- A gassy mine in which flammable gas is found in quantity greater than specified for a Class 22 coal mine. GENERAL NOTES REGARDING DECISION NO. 3 "(A) Flammable gas found in coal mines is, with rare exceptions, methane. In coal-mining fields where natural gas is found in lower geologic horizons by deep wells which pass through or nearby the coal mines, there have been rare instances of la leakage from the well. Natural gas is chiefly methane; that constituent almost always forms more than 85 per cent of the whole, but it usually contains ethane, propane and traces of butane also. Therefore if the latter gases are found in mine air it is an indication of leakage. The lower limit of explosibility of methane-air mixture when there is turbulence of five per cent and of natural-gas-air mixtures with about ten per cent ethane and associated hydro-carbon gases is 4.6 per cent. The limit therefore varies with the character of the mixture. " (B) To determine the proper classification of a coal mine, it is advisable that systematic testing and sampling be done at least three times in a period of not less than 72 hours. All tests and samples of the mine air, except one, must show an inflammable-gas content less than the maximum limit of the class to which the mine is assigned. In other words, a tolerance of one test or analysis may be permitted to provide for a mistake or a very exceptional occurrence. "(C) When a new mine is being opened in a coal field where existing mines are generally gassy, it is common sense to assume that similar conditions will be found in the new mine, and its development and equipment should be based upon the expectation that it will be assigned to Class 3."

Jan 1, 1926

Briefly, the machine consists of a steel frame mounted on roller bearing wheels and axles, an electric motor, a fully enclosed speed reduction gear unit, a specially designed centrifugal pump driven through a friction clutch and silent chain, a mixture tank and agitators, and all necessary operating and control mechanism. The wheels are mounted on solid roller bearings made of special roller bearing steel, and are cast with deep chilled threads. The axles are of high carbon axle steel. A General Electric Company motor, of special design to exclude dirt and moisture, is used. It has an unusual overload capacity and a maximum torque at starting speed. Special arrangement can be also made for storage battery operation. The motor drives from one end, through a flexible coupling, to the speed reduction unit, and from the opposite end, through a similar coupling, to the pump clutch. The design of the flexible couplings is such that the drive is reversible. The speed reduction gears are enclosed in an oil and dust proof housing. All spur gears, as well as the main drive clutch, are made of steel forgings, with accurately cut teeth. An aluminum bronze worm wheel and special heat treated alloy steel worm provide the speed reduction for the traction drive. The worm shaft is mounted on Hyatt roller bearings and the thrust is taken in each direction by ball thrust bearings. The main drive shafts are of special alloy steel and operate in Hyatt roller bearings. The slow speed shafts run in extra large bronze bushings. Ample and constant lubrication is provided by splash from the gears running in oil. The Mudite pump is of special de- sign. A renewable wearing plate protects the pump casing from the natural wear of the mixture. The open runner is mounted on an extra large shaft which runs in a Hyatt roller bearing on the pump end and in Timken roller bearings on the outboard end. A special cage prevents water and grit from reaching the pump bearing. All thrust from the runner is taken on the Tim- ken bearings and these bearings also provide for the accurate and easy adjustment of the runner. The pump is driven by a silent chain, which operates on cut steel sprockets, from a friction clutch. The clutch is designed to secure long wearing qualities with minimum attention and its adjustment is easily effected. It is mounted on Hyatt roller bearings and the clutch drive shaft also runs in the same type of bearings. The pump discharges through a nozzle, which is adjustable, and controlled by the operator. The mixture tank is of approximately 650 gallons capacity. It is provided with a mixing well constructed of perforated plate screen to prevent large hard particles from getting into the valve or pump. The tank is filled through an opening in the top directly into the mixing well. On a shaft running longitudinally through the tank are arms so arranged that the mixture is thoroughly mixed and kept in continuous circulation from end to end. This shaft is driven from the speed reduction unit by a steel roller chain operating on cut sprockets. The traction drive is taken from the worm wheel shaft through steel roller chains of extra large size that run on cut steel split sprockets on both axles. An idler sprocket provides for easy chain adjustment. The axles are mounted in solid roller bearings in fully-enclosed dust proof housings, which support the frame through coil springs. These springs eliminate twisting strains on the frame on account of track irregularities and also relieve the working mechanism from road shocks. The speed reduction from the motor to the wheels is such that it gives an operating speed of approximately ninety to one hundred thirty feet per minute. The brakes are of the conventional shoe type and engage the wheels on both axles. They are operated by a hand wheel conveniently located and

Jan 1, 1925

By Samuel Tescher

The operation of gaseous mines is a problem, due to the fact that we have not only the ordinary mine accidents to guard against, but have also the ever present menace of a mine disaster involving a large number of human lives, and the destruction of valuable property. In looking over the reports of mine disasters throughout the country in the past several years, we find that methane gas, coming in contact with an ignition agency of some kind, has been the source of at least 75 per cent of our mine explosions. Coal dust, of course, plays its part in propagating the explosive action throughout the mine workings and rendering it more violent and destructive; nevertheless, the initial ignition of a body of explosive gas-sometimes of very small volume-has been the primer for the large majority of our mine disasters. We find also, that the places of initial ignition are most frequently found at the working faces, or in close proximity thereto. This is mainly due to the following reasons: First-The working faces are, as a rule, the places where methane gas is most freely generated. Second: They are places that are most poorly ventilated. Third-They are the places where ignition agencies are most frequently found. The sources of ignition, as a rule, consist of naked lights, the shooting -of shots, defective flame safety lamps, and electrical arcs. The problem, then, in the operation of gaseous mines, is primarily to so ventilate the working faces that an explosive mixture is not likely to occur, and to endeavor to keep away from the working faces all sources of ignition. To do both of these things may seem impossible. Nevertheless, by working along both of these directions, a great many disasters can be avoided. The efficient ventilation of the working faces is paramount. By efficient ventilation, we mean the continuous passing of large volumes of air at the working faces. This can only be accomplished by adequate ventilating equipment, capable of being driven by at least two independent and distinct sources of power, together with large, clean, straight air courses which are free of short turns, constructed areas, and leaky doors and stoppings. In other words, furnish a suitable course for its travel through the mine. Many of us sharpen our pencils and rack our brains to properly estimate the proper size pump and pipe equipment that may be needed to handle a certain amount of water. We estimate the size of copper conductors to a nicety. We immediately rush to repair leaks in our water, compressed air or electric lines. But how many of us give serious thought to the travel of the air through our mines, the health and safety-giving fluid on which so much depends! In driving air courses, a certain economical cross-sectional area should be adopted and maintained as standard. When turns are necessary, they should be made with long radius curves, and the cross-sectional area should be increased on the curves. All entry stoppings should preferably be built of monolithic concrete, with suitable hitches into floor and ribs, and after the concrete has set, they should be examined and leaks due to shrinkage and settling should be eliminated. Overcasts and their approaches should have cross-sectional areas larger than the entries leading to them, to allow for the sudden change of direction, bearing in mind that air wants to travel in straight lines. In the early development of a property, ample provision should be made in the size of the main entry pillars to allow for the driving of additional

Jan 1, 1925

By C. H. Trik

Any article or discussion on the ventilation of Working Faces under different systems of concentrated mining is of little value to any practical man unless based upon facts gleaned from actual experience, and empirical data on this subject is, to say the least mighty scarce. Of this one thing, however, you can rest assured, the old cry of "no air at the working faces" will have become a thing of the past. No longer will we hear of some operator who has been too eager to get out the coal and who has lost sight of everything else in his mad dash for production, digging himself shut until his airways are mere pin- points and his air current a feeble thing, too weak to combat the high resistance of his restricted mine. A mine operating under one or more of the various systems of concentrated mining should always have plenty of air, for in concentrated mining the tendency is toward greatly reduced mine resistances due to increased sectional areas. It can readily be seen that the tendency is to large, wide areas across the panel and where this is true large volumes and low gauges are the rule, unless inordinate restriction is encountered in the permanent airways, and no operator, far sighted or progressive enough to adopt this system of mining when his conditions permit, would ever allow his main airways both intake and return, to be anything but model courses. As a matter of .fact, we are likely to encounter the opposite of what is usually the case in most mines to day. We are apt to find the air at the working faces sluggish due to the large areas of passage rather than to high resistance. This is combated in. various ways which will be discussed further along in this article. Those companies, of which we have knowledge in this country who, to- day are using any of the new systems of mining, seem to proceed alike in the general method of developing their acreage. Let us assume, for this discussion, the Utah Colorado Coal Corporation is going to open a mine under the new system and their conditions are such as to permit their adopting the simple block system, each face served by a separate machine, each entry having its conveyor to the cars. After the permanent haulage and airways are driven "narrow work" starts to shape the blocks. We are not interested in the length of these "conveyor headings" since we do not need to drive breakthroughs nor build stoppings for ventilation until we have reached their end when we connect them together. We have two methods of sending air to the face of these dead ends. We can laboriously and expeilsively install brattice cloth, as we go, or we can use a small auxiliary blower with canvas tubing to the face. Indeed I may say that one of the great difficulties encountered under the new systems is in the ventilation of these narrow faces. After they have been connected and an air circuit or current established, ventilation becomes plain sailing until the block is worked out. The auxiliary blower when used with flexible canvas tubing, has been found to be the ideal answer to the question of how to ventilate the headings which are anywhere from 100 to 1,000 feet long. These small blowers when properly used, can go a very long way to assist in further reducing the cost of production already assured by the new method of mining. Right angle bends are made by the tubing manufacturers to enable the fan to sit in the fresh air current, yet out of the way of operations and any recirculation is positively avoided by blowing the air around the corner to the face.

Jan 1, 1926

By John M. Jennings

The Hiawatha pitmouth is located at the head of the middle fork of Miller creek, at an altitude of approximately 8,100 feet. The coal is lowered to the tipple down a gravity tram two miles long, in 16 car trips which carry about 60 tons net. The average running time of the trip is about nine minutes. At the bottom of the tram there are two tracks for the loads and two for the empties. The trip, after being cut off the rope, is dropped by gravity onto a feeder, where the cars are uncoupled and fed one at a. time across the pitcar scales and into the dump. The dump is of the full revolution type, friction driven. On passing out of the dump the cars are returned by a kickback onto the empty car haul. They are caught at the bottom by a brake which consists of a pair of steel squeeze blocks operated by heavy springs. The empties are elevated to the double tracks, where the trips are made up. The feeder, scales, dump and empty car haul are all built on the solid ground of the hillside instead of being incorporated in one structure with the screening plant. The coal is dumped into a small hopper with a capacity of about 15 tons, whence it is fed by a reciprocating feeder onto a scraper conveyor which takes the coal over to the screening plant, a distance of 120 feet. This conveyor is 48 inches wide and travels at 120 feet per minute. The screen itself is interesting. It is of the Marcus Horizontal type.

Jan 1, 1925

By O. C. Irwin

For several years the C. F. & I. Co. men have been working on a fan signal and many different schemes have been tried. I will describe a few of them. A make-and-break attachment was placed on the fan shaft which caused a light to flicker. A hinged door was placed on air course and counter balanced so that it would have a slight travel when the air pressure was reduced an appreciable amount. This motion was used to open the power circuit, blow a whistle, or ring a bell. Series transformers were placed in motor leads of fan drive motor and the variation in amount of power to motor was used to control the fan signal through a magnet or relay. A governor was placed on the fan shaft which opened a signal circuit when speed of fan was reduced. We tried to produce a machine actuated by the volume of air, (that is on the principle of the anemometer) but had to discard this due to its being too delicate. None of the above schemes seemed to fill the conditions which the State and our Mine Inspector wanted covered. They gave us the following demands for a signal: 1. Must open mine circuit and sound alarm when air pressure was reduced below a certain amount. 2. Must be fool proof. 3. Must work on any kind of fan drive (steam or motor). 4. Must be safe to ' install- in any mine or fan house. 5. Must not depend upon mechanical device which could become inactive due to friction or other causes. 6. Must be as simple and easy to adjust as possible.

Jan 1, 1925

By T. H. Butler

February 22nd, 1926. Mr. Benedict Shubart, 521 Boston Building, Denver, Colorado. Dear Mr. Shubart: At your request, am submitting to you several suggestions for the amendment of our safety code which you felt should be kept up to date. As before, am advising you that these suggestions do not have the approval of the entire Safety Committee, but rather are the individual opinions of several members who have expressed their wishes in the form of letters to me. I am particularly indebted to Mr. Dan Harrington and Mr. Wm. Littlejohn for their assistance. Would recommend the following amendment a to the various sections. Section 1. Wherever possible trolley wires should be securely hung to roof or timbers at a distance of not less than five feet and not more than six and one-half feet above rail and six inches to one side. Spacing of hangers should be from 20 to 25 feet apart. Section 2. 500 volts D. C. should not be allowed in any installations. Trolley wires should not carry a voltage of more than 250 D. C. Pumps, mining machines and other small machinery units where A. C. power is used should not carry a voltage of more than 220. Large units, such as pumps, motor genera- tor set and hoists, may use a voltage of 2,200. When power cables to operate same are of armored construction, cables should be securely buried at all crossings. Section 4. Where power lines pass through door frames or stoppings they should be properly insulated with porcelain or rubber tubing. Whenever men get on or off man-trips in vicinity of trolley wires same

Jan 1, 1926

By Margaret N. Maxey

For the past quarter century, it is fair to say that the political agenda of Western industrialized societies has been driven by those opposed to forms of economic growth providing sustenance to a growing population. They regard growth as the major threat to their social philosophy which champions a wholly "new ethic of biocentric equality" or "living as if Nature mattered." This ethic demands that "a violent, plundering humankind" must abandon its alleged rape of Planet Earth and derive its ethical norms from pre-existing harmonies and fragile, precarious balance present in Nature. A Green political agenda appeals strongly to deep longings shared among many people whose temperament seeks tranquillity in a world of wild natural beauty uncluttered by dependency on tools and experts and specialists. According to proponents of the Green philosophy, our world is pregnant with enormous problems. Armed with expanded political powers, regulatory guardians at state and local levels have mustered their forces with shotguns cocked, poised to prod an ignorant and lazy citizenry to the altar for an exchange of vows with Environmental Ethics. Social engineers have skillfully discredited the traditional role of professionals in scientific engineering who are summarily dismissed as the failed architects of an industrial system pillaging the earth. They stand accused of producing unmanageable offspring - from mining minerals and energy resources to disposing of toxic wastes - whose disputed parentage and expectant crimes against humanity must be prevented by removing them from normal custody. Green critics claim that markets cannot be given custody of industrial offspring - pollutants, wastes, land-use abuses. Markets appear to have failed to provide equity to present and future generations. The only custodian with sufficient coercive power seems to be the regulatory bureaucracy. The upshot is a stark Hobson's choice - Shotgun Wedding vs. Custody Dispute. It derives its fateful predestination from an uncritical acceptance of several preconceptions which currently undergird the altar of Sustainability characterized by its acolytes as "a new and exciting doctrine." It is significant that Limits to Growth slogans of the 1970s have been displaced in the 1990s by the more palatable language of Sustainability. As a policy recommended to forestall an impending doom, Sustainability derives its credibility from dire predictions of global warming, ozone depletion, acid rain and the like. The Rio Declaration announced to the world in June 1992 that, although energy is essential to human well-being, its production and consumption in wealthy industrialized nations is unsustainable. It called for a complete overhaul of energy systems with nothing short of a total replacement of fossil fuels, uranium fission reactors, and large hydroelectric projects by means of so-called renewable energy sources, augmented by coercive regulations to force conservation and limit consumption demands. The social and political consequences of such a sweeping

Jan 1, 1995

MR. DICKINSON: There is an increase of dust in machine loading, especially with the McKinlay loading and cutting machine which was extremely dusty. MR. FORRESTER: Declared more dust must be expected because when loading by machinery, the coal is shot harder in order to make it easier for the machine to pick it up. He believes however, that there was less hazard because of the closer supervision possible by reason of the concentration of operation. MR. McAULIFFE: Machine loading more dusty than hand loading. D. HARRINGTON: The hazard is greatly increased by modern methods of loading. Not only do the methods increase the quantity of dust, but they also increase the rapidity of mining and the increased quantity of coal broken down causes large quantities of gas to be released. The number of motors on loading machines and conveyors add to the hazard. No more dangerous places can be found for such motors than at the working face where there is excessive quantities of pure coal dust and where there is more gas than along any other point. Regarding Mr. Herres remarks that the machine loading was safer on account of the concentration and possibility of close supervision, Mr. Harrington said he believed concentration likely to prove a source of danger rather than its preventive. At Dolomite, Alabama, a number of men had assembled, and as a result what was a relatively small explosion killed a large number of men. Concentration is not without its dangers to mine operations. MR. McAULIFFE: These arguments do not appeal to me. Few places are better sprinkled than the working places in a machine loading mine. There is. more effective supervision, and there can be more ventilation. I believe machine loading will increase safety by that very concentration that Mr. Harrington deplores.

Jan 1, 1925