Search Documents

By Mike McWha

Drivers to increasing RM use ?Compliance issues ?Section 12 JSE Listing Rules ?Canadian NI 43-101 ?Sarbanes Oxley ?Shortage of African ore reference materials ?Poor perceptions about quality of some local RM?s

Jan 1, 2005

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By K. G. Philo, R. C. W. Webber-Youngman

mining, where data-driven decision making optimizes resource extraction, enhances safety, and ensures sustainability. The adoption of digital technologies like artificial intelligence (AI) and the Internet of Things has amplified the importance of digital information. However, the integrity and security of this information are paramount, leading to the exploration of blockchain technology as a potential solution for secure digital value exchange in mining. This research examines blockchain's capabilities, drawing insights from its applications in sectors like banking, government, healthcare, and entertainment, and evaluates their relevance to mining's core value chain processes. The study identifies blockchain's distributed ledger technology, cryptographic security, and decentralization as unique advantages that can revolutionize mining by enhancing transaction speed, reducing costs, and improving supply chain transparency and compliance with sustainability standards. Blockchain's transparent and auditable records can enhance business transparency, fostering trust among stakeholders, including investors and regulatory bodies. The technology's consensus mechanisms and smart contracts further promote trust in collaborative ventures. This research provides a foundational understanding for decision-makers in the mining industry to evaluate blockchain's feasibility and potential return on investment, guiding strategic planning and resource allocation for blockchain applications. By leveraging blockchain, mining companies can optimize operations, improve sustainability practices, and establish a robust foundation for future growth, positioning blockchain as a transformative technology in the sector

Jul 10, 2024

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By M. Ataei, F. Sereshki, R. N. Masir

Given the inherent risks and disruptions in underground coal mining operations, strengthening the resilience of critical infrastructure has become a vital priority. This paper aims to evaluate the resilience of the underground coal mining environment using historical data and expert judgment. The study serves as a framework for optimising the utilisation of critical infrastructure to minimise operational disturbances. To achieve this, a practical methodology has been developed, incorporating nearly two and a half years of collected operational data, a hierarchical structure, and a systematic approach. Furthermore, a case study is conducted to demonstrate the real-world applicability of the proposed method. Finally, the resilience index isintroduced as a straightforward summation of ranked impact factors, providing a clear metric for resilience assessment.

Dec 15, 2025

Falls of ground (FOG) still account for around 35 per cent of all fatalities in underground southern African mines. To help reduce FOG, appropriate support technology needs to be implemented, and a mindset and cultural change are required to make a significant change. Discipline plays a major role and needs attention, whilst appropriate first-world support technology is available to assist in the reduction of injuries and the improvement of productivity. Section 54 mine stoppages due to FOG are costly. Appropriate support should reduce these unnecessary stoppages. Coal mining has adapted leading support technologies over the years. Platinum and chrome mines have shown significant moves towards adopting leading and appropriate support technologies, seeing noteworthy changes in injury statistics for the better. In typical conventional underground mining operations, the use of temporary support components offers some protection to workers while the permanent and generally more elaborate support systems are installed or constructed. Nonetheless, FOG continue and still result in injuries to people. The author wishes to explore the options and practicality of making use of new-generation support products and technology to provide not only safer support operations, but to also enhance productivity at the working faces. This paper will examine the use of appropriate support technology as a means to making the working stope or development end a safer and more productive workplace.

Jan 1, 2012

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By T. Bohmer, L. Auret, N. Pillay, Z. Horn, P. Rambalee, A. Haasbroek

As part of a broader digital technology-enabled transformation programme, a major mining company is systematically implementing Advanced Process Control (APC) solutions and associated instrumentation throughout their operations. This paper highlights the approach and benefits of this holistic approach for a specific instrumentation installation, and APC installation at a South African coal processing plant. For the coal processing plant under consideration, a systematic approach was followed. Process sections/units are considered from upstream to downstream processing. APC solutions are designed for each process section and each process section is interrogated in terms of availability of sufficient process measurements to ensure stable, capable, and ultimately, optimised performance. Where insufficient process measurements are available, instrumentation upgrades are implemented. Finally, APC solutions are implemented, and evaluated in terms of productivity, safety, health, and environmental benefits. For the flotation section, an opportunity was identified to install froth sensors. The installed froth sensors provide measurements on froth velocity, bubble size, height, colour, and stability. The improved visibility that the froth sensors provided on the flotation process resulted in quick gains in terms of productivity: for example, instability in the feed to the flotation section could be quantified. This resulted in targeted process troubleshooting in an upstream thickener, and subsequent improvement of process stability, and reduced feed variance. The measurements from the froth sensors were further integrated in an APC solution. Proportional mass pull contributions per cell and per line can be inferred from the froth sensors, serving as controlled variables, while pulp level set points serve as the manipulated variables. On-off tests indicated that the advanced process control solution provided increases in yield and product quality.

Sep 1, 2021

By T. Bhambhani, E. Arinaitwe

Solvay has developed several novel reagent innovations to improve separations in sulfide ore flotation and address major industry challenges. These innovations include: a) carbon management strategies to reduce the deleterious impact of organic carbon on flotation circuits; b) new collectors for heavily tarnished or oxidized Cu-Au ores; and c) a functionalized depressant for minimizing penalty elements in metal concentrates. Owing to their unique chemistries, these innovations exhibit a wide spectrum of rather unique properties that are quite in contrast to the traditionally used reagents. The chemistry, attributes, application, and advantages of these innovations are discussed in this paper based on laboratory, pilot, and plant results and observations for various ores

Jan 1, 2023

By R. Mumbi, M. Peart, E. Arinaitwe, B. Mbao, J. Zulu

Since 1925, xanthates have been widely used in sulfide flotation due to their low cost, ease of manufacture, and ability to float most value species. However, the industry's increasing need for safer and more selective alternatives, driven by low head grades, poor-quality, difficult-to-process ore with complex mineralogy, and stricter environmental regulations, has led to the development of Solvay's AERO® XR series of collectors. These custom-formulated products are based on greener chemistries and offer metallurgical benefits that are similar to or better than those of xanthates, without the safety concerns. Developed through Solvay's Flotation Matrix (FM) 100 approach, the XR series collectors are suitable for a wide range of applications, including the processing of Cu, Zn, and Cu-Ni, as well as the flotation of precious metals. This paper will highlight the differences between xanthates and XR series collectors, and present case studies of their successful commercial application at various global operations.

Jan 1, 2023

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

By J. Petersen, T. Moyo, D. Maharaj

This study investigates the effect of ammonium thiosulfate on the leaching of gold from the contacts of unpopulated cut electronic printed circuit boards (PCBs). Studies in the literature show ammonium thiosulfate to be a viable option in comparison to the commonly used but hazardous cyanide leaching route. However, the simultaneous dissolution of Cu interferes with the Au leaching reaction, often limiting the extraction to moderate levels. To optimize the system, an ammoniumthiosulfate system containing 0.5M ammonia, 0.5M ammonium thiosulfate, and Cu(II) sulfate at varying concentrations was studied as an alternative hydrometallurgical option for the recovery of gold from PCB. Tests were done with unpopulated standardized model PCBs (cut to 15 x 30mm pieces). Gold extraction of 47.3% was achieved after a 24-hour leaching experiment with a 0.02M copper background concentration. Further experiments focused using different initial background Cu concentrations (0M – 0.1M) to determine its effect on both gold and copper extractions. An initial Cu concentration of 0.045M resulted in the highest gold extraction, with 93.7% extraction after 6 hours of leaching. Further analysis of the data shows that the kinetic rate of gold leaching is correlated in a first-order dependence with the actual copper concentration in the solution, which increases with the concomitant dissolution of copper and gold from the PCBs. A lower threshold of 0.017M and an upper threshold of 0.15M copper in solution were determined, in between which gold extraction shows this first-order rate increase. The upper threshold is potentially linked to the onset of copper precipitation, which blinds the metal surfaces, slowing further leaching. The findings of this study suggest that in an industrial recovery operation of gold from waste PCB using the thiosulfate method, copper concentrations need to be carefully monitored, and the process should preferably operate with uncut or coarsely cut untreated boards to minimize exposure to copper circuits.

Dec 11, 2024

By A. Rödfalk, P. Bloemer, J. P. Nilsson, N. Brogden

"Reliable and accurate metal transfer information during silicon tapping from an EAF is invaluable for decision-making and process optimization, while obtaining such information safely is a necessity.Elkem Thamshavn Norway, a producer of metallurgical-grade silicon, identified inherent safety problems with gauging fill levels in ladles using dip bars while molten metal was continuously pouring from a rotating EAF. Operator safety was a paramount concern, and an alternative automatic method of controlling the tapped fill level needed to be found.It was also considered that further benefits could be achieved such as monitoring the tapping flow from the EAF in order to identify any clogging, as well as the potential to use the live feed from such a system to assist decision-making regarding work around the taphole area.Agellis Group AB, Sweden, a company with over 30 years of experience in gauging molten metal levels in the metals industry, was able to design a solution for Elkem Thamshavn that would provide the required real-time process data while enhancing operator safety.This paper shows how the Agellis AB EMLI-L system was successfully installed at Elkem Thamshavn’s EAF continuous tapping area, how ladle fill levels were constantly monitored, and how full ladles were replaced by empty ones without the need for operators to be in the tapping area to take level readings. The results were used to compare the accuracy and reliability of Elkem Thamshavn’s current measuring methods with that of the EMLI-L system. The paper also covers how problems such as how to connect, run, and protect cables in and around the EAF tapping area, as well as connector and cabling survivability during the three day refractory pre-bake period, were solved. Finally, the paper discusses the potential production improvements, maintenance requirements, and data integration attainable through the installation of the system, as well as the major safety improvements that have been achieved."

Jan 1, 2014

Keywords: Pyrometallurgy, zinc, electrowinning Zincor has been producing zinc since 1969 via the roast-leach-electrowinning process. It is the only primary zinc producer in South Africa, and currently supplies the entire country with zinc. The plant was built by Goldfields of South Africa, on the site of an old gold and uranium mine. Since then, the ownership of the plant has changed a couple of times, and the plant and process have also been improved. Production output has increased from around 80 000 tons per year to more than 110 000 tons per year. This was done mainly through increasing the capacity of the roasters and acid plant. Zincor produces four main grades of zinc: SHG, Zn1, Zn2, and Zn4, in three shapes: a 25 kg ingot and 1 and 2 ton jumbos. In 2005, a pre-alloy furnace was built that enabled the production of jumbos pre-alloyed with aluminium. This has allowed Zincor's customers to improve the efficiency of their continuous galvanizing lines and to lower their production costs.

Jan 1, 2006

"I have been involved in the refractory industry for many years and at some time or another I have designed materials, tested materials, manufactured materials, installed materials, in fact I have done everything except actually chemically analyzed a refractory material.So I would not even begin to tell you how to analyse a refractory material. I'm sure everyone here knows more about chemical analysis than I do.However you could regard me as a customer with and perhaps the insights I have developed may help in putting the role of chemical analysis in the Refractories into perspective.For a start, let's take a step back and ask why we test refractories. The refractories handbook of the American Foundry Association gives four reasons:1. To determine appropriate specification.2. For quality control, to ensure conformance to specifications.3. To provide special property information not available elsewhere.4. For postmortem analysis to determine property changes in service and provideinformation that can point the way to better service.I want to discuss these points with regard to the role of chemical analysis and in particular the abuse of in house chemical analysis facilities. Let me talk first about detelmining appropriate specifications. Most refractory products are made from alumino-silicate raw materials.The phase diagram for alumino and silica is as follows:"

Jan 1, 2014

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016