Search Documents

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014

By P. G. Gresse

The Orange-Vaal River system is known to be the primary secondary source for alluvial diamond deposits in the northern Cape and along the west coast of Namaqualand. The higher order sources for diamonds contained within this system are still not defined entirely to satisfaction, but certainly include kimberlite pipes exposed in the catchment regions of these rivers. The focus of alluvial diamond mining along the Orange-Vaal system recently changed from the traditional areas in the upper catchment regions?the Barkly West, Christiana, Bloemhof, Wolmaranstad, Schweizer-Reineke region, and the lower regions near the mouth of the Orange River at Baken, Alexander Bay and Oranjemund, to the area between Douglas and Prieska?the so-called mid-Orange region (Figure 1).

Jan 1, 2003

By I. M. W. Preston

A new shaft system was required to replace stope face for the North Section of Harmony Mine and to allow for systematic opening up of the North Eastern Section. Owing to the economic circumstances at the time the project started, it became vital to alter the original planning and to sink the service shaft first. The MATLA coal-sinking headgear, a novel presinking arrangement, allowed sinking to continue to 108 m concurrently with the erection of the permanent sinking headgear and sinking winders. It is estimated that this arrangement resulted in a saving of two months on the overall project.

Jan 1, 1983

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By B. R. Broekman, D. W. Penman

SYNOPSIS This paper traces the developments in flotation practice at Anglovaal's Prieska Copper Mine, with em¬phasis on the depression/deactivation of lead and zinc. A depressant system was devised to accept feed material that was once regarded as untreatable. Of particular interest is the long-term downward trend of concentrator working costs in real terms. This trend follows the classic Experience Curve, which relates production costs to cumulative experience. It is felt that the experience-curve concept has important implications for the mining industry in general.

Jan 1, 1991

By B. R. Broekman, D. W. Penman

Discussion by P.J Lloydt Broekman and Penman describe (J.S. Afr. Inst. Min. Metal., vol. 91, Aug. 1991, p. 261) the addition of sodium cyanide and zinc sulphate to the flotation feed at Prieska. They note that for 'safety sake, lime was added to the rod mil to raise the pH to 9,5', and that 'personnel working in the vicinity of the rod mil were required to wear gas masks'. Author reply to P.J. Lloyd We thank Dr Lloyd for his interesting contribution. As he correctly points out, the Prieska float had run with cyanide solutions at pH values of 6,4. In fact, it ran safely for extended period with the pH slightly below 6.

Jan 1, 1991

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

By L. Stamenov, A. Grigoryan, M. Nolte, E. Ayvazov, K. Evtiminova

Dundee Precious Metals Inc. (DPM) owns and operates the Ada Tepe gold mine and processing facility (previously referred to as the Krumovgrad Gold Project) located in south-western Bulgaria. The Ada Tepe mine became the first green filed project in past 40 year in Balkans and one of the few in Europe when it was commissioned during the first half of 2019. The plant produces a high-grade gold silicate concentrate generated through its comminution circuit and staged floatation reactors (SFR’s) while depositing its tailings in a state-of-the-art Integrated Mine Waste Facility (IMWF). This paper presents the successful commissioning, ramp-up and optimization of the Ada Tepe processing plant and how the various challenges, including that of an inexperienced front-line workforce, were overcome. More specifically addressing how the implemented modern processing technologies and the operational readiness program, supported the people and process to achieve the design parameters safely and consistently. Keywords: Commissioning, Optimization, Innovation, Gold mine, Digital mine

Jan 1, 2020

A brief overview is given of the issues regarding the processing of waste electrical and electronic equipment (WEEE). The printed circuit board component of WEEE is an exceptionally complex feed to possible recycling processes. Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy. Iron and aluminium were found not to be part of the alloy. The alloy was characterized by SEM-EDS, and three phases were identified: alpha and delta bronzes, and a lead-rich phase. Calculations show that about 56 mass per cent of the alloy is the alpha phase, 35 per cent delta phase and 9 per cent lead phase. A simplified approach using appropriate binary phase diagrams was used to derive a phase composition for the alloy. This was further backed by FactSage calculations, which showed that the simplified approach was appropriate for this alloy. The experimental findings and theory were found to agree well.

Jan 1, 2009

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

By E. H. van Niekerk

The production of high-strength Iow-alloy (HSLA) steels containing either niobium or vanadium as the principal micro-alloying element is discussed, including recent developments in steelmaking practice that have had a great effect on the development of HSLA steels; strengthening mechanisms, as well as the principles of thermomechanical treatment during controlled rolling on a hot-strip mill; and the results of production heats with various amounts of micro-alloying elements.

Jan 1, 1984

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By B. Strohmeier

The role of large, ultra-high-powered arc furnaces in a fully integrated steelworks for the production of flat products is outlined, and an account is given of the technological improvements that have been implemented over the past few years to enable the arc furnace to remain competitive against the conventional route using blast furnaces and top-blown-oxygen steelmaking (LD). Modern secondary refining facilities have been installed, enabling the arc furnace to operate at high production rates in the manufacture of high-quality flat products.

Jan 1, 1985

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By D. W. Horsfall

This paper reviews the properties and uses of mixtures of coal with fuel oil, methanol, or water, emphasis being placed on mixtures of coal and water. The material presented is taken from studies conducted overseas, and it is recommended that similar studies should be conducted on mixtures containing South African coals, which differ from the coals of the northern hemisphere

Jan 1, 1990

By H. J. de Klerk

The metallurgical phenomena in the design and manufacture of high-strength low-alloy (HSLA) steels are reviewed, and some aspects of the production of Supraform TM (thermo-mechanically processed) steel are discussed. . The weldability of Supraform TM is related to changes in the microstructure of its heat-affected zone.

Jan 1, 1984