Search Documents

By A. A. Hazell

Mine management by objectives by A. A. Hazel Published in the Journal, September 1972 DISCUSSION H. H. McGREGOR Mr Hazell is to be complimented on a thoroughly down to earth analysis of the uses ot which work study can be put and the benefits of properly applying it in the management of underground production.

Jan 9, 2007

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By Johanna van Deventer, Sean Scott, Rene du Preez, Steven R. Izatt

In order to meet the stringent specifications associated with the production of LME Grade A cobalt cathode, producers need to ensure that a number of impurities, including Cd, are removed from the advance electrolyte to ppb levels (~0.1 mg/L). Conventional options include ion exchange using amino methyl phosphonic acid resin and solvent extraction using D2EHPA. More recently a Cd-selective resin, employing Molecular Recognition Technology (MRT), became available from IBC Technologies, Inc. These three potential unit operations were evaluated in parallel at Mintek. MRT was identified as the most technically feasible option. Results obtained on a cobalt advance electrolyte, containing 55 g/L Co, 6 mg/L Cd and 60 g/L Na2SO4, are presented in this paper.

Jan 1, 2007

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

By Y. -L. Chiang

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) The generation and control of manganese sulphide particle size distribution using various mixing configurations were investigated. Specifically, this paper discusses how varying mixing intensities on a macro and micro scale affect the resultant manganese sulphide particle size distribution (PSD) at a constant concentration. The mixing variations were achieved using various Y- and T-mixers as premixing devices into a jacketed, agitated vessel. The reagents used to generate the seeds were aqueous manganese sulphate and sodium sulphide solutions. The results showed that the absence of micromixing resulted in very poor control of the particle size distribution, the particle size and the number of particles produced. This was due to the fact that the macromixing time is much greater than the corresponding precipitation time, resulting in different mixing regions existing within the reactor. From the micromixing experiments, the T?mixer was found to be the most effective mixing device at lower concentrations due to the T-mixer providing a faster mixing time than the other mixing configurations, thereby effectively localizing the supersaturation and hence controlling the precipitation. The results obtained from the direct addition without the extension pipe (i.e. short mixing time) indicated a general increase in mean particle size and decrease in total particle number at reagent concentration of 0.007 mol.dm-3as compared to the corresponding micromixing experiments. The phenomenon may be due to incomplete crystallization at the immediate exit of the mixing device. Further experiments need to be conducted before any conclusions can be drawn about the precipitation mechanisms.

Jan 1, 2007

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By Dechun Lou, Benjamin Ravary, Merete Tangstad, Stein Wasbø, Sean Gaal

The melting phenomena of manganese ore, slag and alloys were studied in an experimental sessile drop furnace. Particles of approximately 20-60mg were placed on graphite substrates and then heated at a constant rate of 5°C/min up to 1830°C in a controlled gas atmosphere of Ar or CO. The shape of the particle was photographed with a digital video camera every second. It was observed that the melting behaviour can vary significantly, with some particles exhibiting a large softening/melting range. Selected samples were sectioned and then analysed with EPMA. The implications of the results on understanding industrial furnace operations are discussed.

Jan 1, 2007

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By J. G. Bruwer

Paper written on project work carried out in partial fulfilment of B Eng Met Surface coatings persisting on zircon particles, after being leached in an acidic solution, are believed to be the cause of zircon misplacement during the electrostatic separation of heavy mineral beach sands. Electrostatic separation is employed to separate non-conductive zircon particles from more conductive rutile particles. Surface coatings on zircon particles are believed to render the non-conductive zircon particles more conductive, resulting in the contamination of the more conductive rutile stream with zircon particles. Resistivity measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed to compare the surface characteristics of zircon particles found in the different product streams following electrostatic separation. XPS analysis showed that no significant difference exists in the outermost layer of the zircon particles found in the different streams. SEM analysis showed the existing surface coatings on zircon particles from different product streams to have similar chemical compositions. Resistivity measurements confirmed the results obtained from both the XPS and SEM analysis; no significant differences in the resitivities were observed. From the results obtained it suggests that surface coatings present on zircon particles are unlikely the primary cause of zircon misplacement. Zircon losses can possibly be a result of machine related aspects. Key words: XPS; SEM; resistivity measurements; electrostatic separation; heavy mineral sands.

Jan 1, 2007

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By Swapan Ghosh, Amitava Sengupta, Proloy Das

Ferro-alloys are very important ingredients used for making of quality steel with desired composition. In view of high demand in various types of ferro-alloys, it has become necessary to produce the same efficiently, safely and cost-effectively with consistent quality maintaining the anti-pollution norms. To achieve this goal, it is necessary to adopt latest process/equipment with the state-of-the-art instrumentation and automation system. A Programmable Logic Controller (PLC) based automation system with suitable Human Machine Interface(HMI) terminals along with intelligent field mounted sensing/control devices allows to monitor and control the complete plant effectively with optimum deployment of man-power. In association with this, use of process optimization controllers enables to achieve specialised functionalities of the submerged arc furnaces like material management, lining management, electrode management, power management, overall production management etc.

Jan 1, 2007

By A. M. Engelbrecht

Paper written on project work carried out in partial fulfilment of B Eng. (Chemical) Membrane processes are vital to a diverse range of technical and biological systems, which also feature in mineral processing applications such as the treatment of mine effluent and extraction of metals. In this study, the use of cellular automata to model a semi-permeable membrane that separates two compartments is considered. Cellular automata are simple models that enable the analyst to represent well-understood local effects, such as the chemical or steric interaction between molecules themselves and between molecules or particles and their environment, which can lead to very complex behaviour on a macroscopic scale. Various physical phenomena, including reverse osmosis, were simulated. Initial results for the effect of temperature, membrane structure and chemical properties of the solutes on the performance of the membrane appear promising. Keywords: cellular automata, dynamic modelling, filtration, membrane fouling, osmosis.

Jan 1, 2007

By H. Jeram

The ilmenite, rutile and zircon processes of the mineral separation plant generate tailing streams, which still contain valuable mineral. This is due to a combination of factors, which include separator equipment efficiency, particle size effects and inefficient operating practices (equipment overloading, blockage, etc.). Recent developments by metallurgical equipment suppliers have led to increased mineral separator performance enabling recovery of previously lost valuable mineral. Mineralogical studies were conducted using QEM*SEM and MLA techniques to identify and quantify gangue mineral species and determine mineral association. Laboratory and pilot-scale test work was then conducted to develop suitable process flowsheets for the recovery of ilmenite, rutile and zircon from current and stockpiled tailings.

Jan 1, 2007

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

While some of the practical details of ilmenite smelting are not well documented, there is a substantial body of literature on the principles of ilmenite smelting, and the behaviour of solidified titania slag. This information is summarized, focusing on the basic reactions, departure from equilibrium, the behaviour of impurities, and reactions of solidified slag. The emphasis is on the South African operations.

Jan 1, 2007