Search Documents

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By P. K. Sahoo, C. R. Ray, S. S. Rao

This paper deals with various factors affecting the strength of chromite briquettes which plays a vital role in the smelting of charge chrome / ferro chrome production. Appropriate briquetting parameters like molasses and lime binder level, molasses quality, particle size distribution and segment condition etc. are essential to guarantee quality briquettes in the successful use of briquette and chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the grain size characteristics of the chrome ore fines but also to make an informed choice of the type and quality of the binder and the condition for producing a physically and chemically competent green and cured briquette. This paper also describes the effect of strength of briquettes on various parameters of charge chrome production as the use of quality briquettes in the production of high carbon ferrochrome alloys has a number of operational, metallurgical and economic advantages. It is also a requirement for submerged arc furnace operation that the charge be adequately porous to allow gaseous products of the reduction reaction to escape from the furnace charge burden without hindrance. Otherwise, furnace material would erupt causing electrodes and furnace other equipments damage and risking the safety of the work force. The briquette, because it replaces lumpy charge but has an advantage of smaller size, allows for an uniform and porous charge so that the ascending gaseous products can escape freely. Finally this paper deals with furnace operational results with varying proportion of briquettes having same strength.

Jan 1, 2007

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world?s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of ca. 160 ? 250 Mt; however, all previous attempts to extract the PGE from this ore type proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas arsenide- and sulphide-PGMs, making up ca. 25 per cent of the original Pt content of the ore, largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd)-oxides or hydroxides, or in iron-hydroxides, Mn?Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2012

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By G. L. Dyer, R. D. Alorro, R. E. Browner

A potential new rare earth extraction process has been suggested (Lazo, et al., 2017) (Lazo, et al., 2018) based on converting the rare earth elements to solid phase rare earth oxalates in an oxalic acid leach. Oxalic acid consumption is a significant issue in the process, therefore to improve the viability of this proposed new extraction method, a process to recover oxalate from the leach solution and recycle oxalic acid is required. A review of the literature and confirmation through thermodynamic analysis of the potential options identified precipitation of calcium or ferrous oxalate as the best potential options. The use of metallic iron to both provide ferrous ions as a precipitant and reduce ferric ions in solution would provide the most economical option, however slow kinetics and unreacted iron created significant issues with this process. The direct use of ferrous ions, while faster and more efficient, produced a precipitate with relatively poor solid/liquid handling characteristics and would require an intermediate stage utilising calcium in regenerating the oxalate. Utilising calcium chloride and oxide created very similar precipitates with better physical properties than the ferrous oxalate and that a reasonable proportion of the oxalate could be recovered before neutralisation of the solution induced precipitation of other phases such as iron oxy-hydroxides and calcium phosphate. The produced calcium oxalate was easily converted to oxalic acid and gypsum via immersion in sulphuric acid. It was also found that there is a significant loss of oxalic acid due to factors other than rare earth oxalate precipitation during leaching. This leads to a maximum oxalate recovery in the range of 50 %.

Jan 1, 2020

By R. H. Estrada-Ruiz

This work analyses a new approach to estimates bubble size distribution of froth surfaces using artificial neural networks (ANN).Also, the robustness of ANN to interpret images with illumination perturbations, produced by light problems or dirt attached to the window of the video camera is evaluated. The experimental work was carried out in a laboratory flotation column, instrumented with an image acquisition system. The images were processed making use of a perceptron model with a hidden layer, sigmoidal transfer function and unitary bias, and the ANN trained with a back propagation algorithm. The results of validation show that ANN are reliable for learning and producing generalized predictions of the froth mean bubble diameter and bubble size distribution, when the model is trained using a database that contains information on the illumination intensity. Keywords: image analysis, neural networks, bubble diameter, bubble size distribution.

Jan 1, 2009

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By Austin Whillier, Duncan Mitchell

The problem of heat stress underground in the gold mines is approached on the basis of the heat transfer between the human body and the underground environment. Experimental measurements of radiant and convective heat transfer and a theoretical calculation of maximum evaporative heat transfer enable the maximum cooling power of an environment to be calculated in terms of the dry-bulb and wet-bulb temperature, the mean radiant temperature, the wind speed and the barometric pressure. For most underground applications the cooling power can be expressed as a function of wet-bulb temperature and wind speed only. The relative importance of wind speed and wet-bulb temperature can be assessed: in working places where wind speed is low additional cooling of workmen can be achieved better by increased wind speed than by decreased wet-bulb temperature. The wet kata reading proves to be of limited value as an index of heat stress because environments with equal wet kata do not necessarily have the same cooling power. Finally, thermal equilibrium with the environment is possible when cooling power equals or exceeds the rate of metabolic heat generation. The rates of metabolic heat generation for various underground tasks are indicated.

By Ishwinder Grewal, Michael Fullam

Many factors affect the overall performance of a gravity circuit beyond that of the primary gravity recovery device. It is critical to examine the gravity circuit in its entirety in order to determine the dominant operating variables that affect overall performance. Knelson has developed a mathematical model which has been used to assist in the design of gravity circuits, and in particular, in making accurate predictions of plant scale gravity recovery. More recently, inclusion of recovery by particle size class and additional data from various mine sites and research studies has made the model more robust. The model is now able to predict GRG (gravity-recoverable-gold) recoveries using various devices such as centrifugal concentrators, shaking tables, jigs and flash-flotation within the grinding circuit. The benefits derived by these recent advancements in modeling capability are two-fold; the first is as a tool to assist in circuit design and correct equipment selection and the second is as an analytical tool to help to evaluate and enhance the performance of existing gravity circuits.

Jan 1, 2006

By B. Genc

"The risk of spontaneous combustion is well known in the South African coal mining industry. In the coming years it is very possible that the incidence of spontaneous combustion will increase from current levels, due to factors such as an increased rate of mining, re-working of previously mined seams, more stooping and total extraction for underground mines, and higher stripping ratios for surface mines, leading to more spoils. It is also fairly certain that coal mining will face tougher environmental emissions legislation in the near future. To determine the areas where the risks of spontaneous combustion are high, it is necessary to improve on our current laboratory procedures for testing and evaluating coal samples, combining the results with site and field data, and if necessary revising the laboratory rating system to refine our understanding of South African conditions.Currently, laboratory tests are conducted in order to determine both the Wits-EHAC index and the crossing-point temperature which, when combined, give an indication of the spontaneous combustion propensities of the coal samples. This procedure has enabled the establishment of a database of results to review and evaluate South African coal seams. Using this database, the high-risk areas in terms of spontaneous combustion are identified. Tests have been undertaken for five consecutive years, between 2008 and 2012. In total, 119 coal samples from different coal seams and production coalfields have been analysed and classified through a series of laboratory tests. A comprehensive database of these results is available, and is continually being updated as new test results are added. This database will continue to expand, and to provide the basis for an improved risk evaluation methodology for spontaneous combustion"

Jan 1, 2015

By T. Wettainen

Malmberget town is located in northern Sweden, approximately 70 km north of the Arctic Circle. Parts of the town overlie more than 20 iron orebodies, consisting mainly of magnetite with smaller quantities of haematite. The mine is operated by the mining company LKAB. Mining started in the 17th century, but not until the railway to the coastal city of Luleå was completed in 1888 did large-scale production commence. Around 1920, mining proceeded underground and today sublevel caving is the only mining method used. Sublevel caving causes subsidence of the ground surface, and buildings and residential areas have been relocated due to the mining activities for more than 50 years. The number of seismic events accompanied by strong ground vibrations is now increasing. In 2008 the mine received a permit from the Environmental Court of Sweden to increase production to 20 Mt of crude ore per year. A prerequisite for the permit was that the mine conducts a number of investigations regarding the environmental impact on the residents of Malmberget. One of these investigations concerned how seismicity will change as production increases and what measures could be taken to reduce inconvenience to the town residents. Today the mine possesses an extensive seismic monitoring system with more than 180 underground and surface geophones. For this study, eleven seismically active volumes in Malmberget mine were identified, and for each of them, a yearly future maximum magnitude interval was estimated based on the current production plan. Relationships between historical seismic events and measured ground vibrations in the town of Malmberget were established, and future ground vibrations caused by expected seismic events were estimated using a probabilistic approach. The outcome was the number of intervals of expected ground vibration per year and per monitoring point. Possible measures to reduce inconvenience for the town residents include blast restrictions, sequencing, and possibly preconditioning. The ultimate long-term solution is an almost complete relocation of Malmberget town. This process has recently been formalized and LKAB is taking an active part in realizing this goal.

Jan 1, 2014

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By A. P. Squelch

The high incidence of accidents and fatalities in the South African mining industry, in particular those associated with falls of ground, is often attributed to ineffective and/or inappropriate training methods and material. Recently introduced mine health and safety legislation in South Africa also requires that all mine workers receive appropriate and effective training to enable them to operate safely in their given mining environment. There can, therefore, be no doubt that methods to provide effective training, in particular safety related training, are urgently required in the South African mining industry. In the search for alternative and improved training approaches, attention has fallen on virtual reality (VR) technology as a possible solution. VR has found acceptance in a number of industries as an effective method of training for a variety of work place activities, including those of a safety related nature. VR has successfully been applied in a number of industries to improve the effectiveness of safety and hazard awareness training. The CSIR: Division of Mining Technology (CSIR Miningtek), in conjunction with the Safety in Mines Research Advisory Committee (SIMRAC), therefore evaluated the potential of VR to be used as a training medium in the South African gold and platinum mining industry. Aspects of the evaluation included an assessment of the technical capability of VR to represent a typical underground mining environment with sufficient realism and the relevance of the VR training concept for a largely illiterate workforce. For these purposes, a prototype PC-based VR hazard awareness training simulator has been developed by CSIR Miningtek, and a series of evaluation sessions conducted at a typical deep level gold mine. The conclusion from this evaluation work is that virtual reality technology has the potential to provide effective training systems that are relevant to the South African mining industry. Keywords: Virtual reality, mine training, safety training.

Jan 1, 2001

By H. Moosberg-Bustnes

In cement-based products, such as concrete and mortars, a balance between the particle sizes of the components must be kept in order to obtain the required material properties, such as workability and strength. Sometimes the aggregates lack the necessary amount of fines, hence fine particles, i.e., filler materials, have to be added. Large quantities of filler material are needed in the production of modern concrete types; one principle of self-compacting concrete (SCC) is, for instance, the use of large amounts of fillers to reduce the friction between the coarser aggregates. Use of by-products such as slag, dust or sludge from the metallurgical industries as filler materials in concrete may help to conserve natural resources and at the same time be an economically positive option. However, to be able to successfully use the available materials they must be suitable for the planned purpose, i.e., they must be compatible with cement. In this paper three different experimental studies of steel-slags will be discussed. The aim of the studies has been to investigate if it is possible to improve the steel-slags properties, by selective screening, fine wet grinding or remelting, so that the steel-slags can be used as mineral-addition/filler material in concrete. Keywords: concrete, filler, steel-slag, modification

Jan 1, 2004