Search Documents

By K. Cybulski

In 2002 a coal dust explosions occurred in the Polish collieries “Jas-Mos” and “Rydultowy” in the Upper Silesia coal basin. In the “Jas-Mos” colliery the coal dust explosion was initiated in the face of gallery by explosives and causing ten death. The stone dust barrier extinguished the flame, stopped the explosion development and saved forty nine miners working in that area. In the “Rydultowy” colliery methane inflammation caused three deaths and seven serious burns and ignited the coal dust explosion. The coal dust explosion was stopped by stone dust barrier and did not cause any victims itself. This paper presents the investigation carried out by the Central Mining Institute Experimental Mine “Barbara” and shows that the stone dust barriers remain still a basic mean for suppression of coal dust explosion in mines. The investigation were aimed at determining the cause of explosion and circumstances that led to their propagation. The evaluation of the state of dust explosion hazard in the areas of accidents have been performed, and the range of flame estimated.

Jan 1, 2003

By O. I. Ostrovski, D. K. Belashchenko

The aim of this paper is the construction of models of systems with ionic and ionic-covalent bonds (molten salts) using experimental diffraction data and the calculation of their structure and thermodynamic and transport properties. Modelling was performed using algorithm BELION, in which the non-coulomb part of interaction potential between ions in the model was determined by the method of iterative simulation which targeted agreement between calculated and experimental partial pair correlation functions (PPCFs). The ionic charges in salts, which can be fractional, were determined by minimization of internal energy. In this paper, the algorithm BELION is applied for chlorides of alkaline-earth metals. Pair potentials, PPCFs, atomization energies, self-diffusion coefficients and electric conductivity are calculated. The charge of alkaline-earth metals was in the range of 2.0-2.1, slightly increasing from Mg to Ba. Partial pair correlation functions and atomization energies of models agree well with experimental data for MgCl2, SrCl2and BaCl2. Keywords: molten salt, molecular dynamics, partial pair correlation function, ionic charge, atomization energy, diffusion.

Jan 1, 2004

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

By Y. Mitani, F. Vallier, T. Esaki

Shear-flow coupling tests are conducted using an original apparatus, and a shear-flow coupling model using Geographic Information System (GIS) is developed in order to evaluate shear-flow coupling properties of a rock joint. Shear-flow coupling tests indicate that the hydraulic conductivity of joint once decreases, and then rapidly increases at the shear displacement near the peak shear stress. The proposed model simulates the test results relatively well. However it indicates that it is difficult to apply the local ‘cubic law’ model in the initial shear stage, in which the change of selective flow path is remarkable. Scher-Fliess-Kopplungsversuche werden mit einem neuartigen Versuchsgerät durchgeführt und mithilfe von Geo-Informationssystemen (GIS) gedeutet, um so ein Modell für die Scher-Fliess-Kopplung in Gebirgstrennflächen zu entwickeln. Die Versuche zeigen, dass die hydraulische Leitfähigkeit zuerst abnimmt, dann aber schnell wieder zunimmt sobald die maximale Scherfestigkeit erreicht ist. Das vorgestellte Modell bildet die Testergebnisse relativ gut nach. Es zeigt auch, dass es schwierig ist, das lokale Cubic Law im Initialstadium der Scherbeanspruchung anzuwenden, in dem die Variationen selektiver Fliesswege gross ist. Les essaies hydro-mécaniques couplés en cisaillement sont réalisés grâce à un appareil éxperimental prototype et un modèle de couplage hydro-mécanique utilisant le S.I.G (systeme d'information géographique) développé dans le but d'évaluer les propriétés hydro-mécaniques des joint rocheux. Les résultats indiquent que la conductivité hydraulique des joints décroit puis augmente rapidement en se rapprochant du pic de cisaillement. Le modèle proposé simule relativement bien les résultats expérimentaux ; mais indique également qu’il est difficile d’appliquer localement la loi cubique au début du cisaillement où, les changements d’orientation dans le réseau d'écoulement sont considerables.

Jan 1, 2003

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By D. M. Poulter, J. N. Brooke, P. H. Williams

"The complexity of the mining and metallurgical operations of Nchanga Consolidated Copper Mines, Limited, has made it necessary to use computer-assisted planning techniques in order to maximize copper production and marginal contribution to profit. The most successful of the Group Production Scheduling systems utilized linear programming to optimize the concentrate routing only. This third-generation system was commissioned in March, 1968.It bad become necessary by March, 1970, to expand the long-term planning activities and to take into account new mines and new concentrate treatment schemes. Technical difficulties and manpower limitations made it impossible to expand the third-generation system, and it was decided to construct a new Group Production Scheduling system using only linear programming.The plant models in the new fourth-generation system are based on data available from the monthly reports of the metallurgical plants. The models consist of mass balances and empirical relationships. Matrix coefficient assignment and management reports are produced using a Report Generator Language designed for linear programming data files. The development of this system is an example of a user application of a system package."

Jan 1, 2014

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

By J. P. Hoffman, A. S. M. de Jesus

Additions of boron have been found to increase the hot workability of stainless steels. Boron forms complex chromium-iron borides, primarily at grain boundaries but also on delta-ferite stringers. This paper describes how a nuclear technique based on the track-etch method was used to distinguish between borides and chromium carbides on grain boundaries and to investigate the distribution of boron in stainless steels. The method was found to be sensitive for boron, and made it possible for boron precipitates to be identified on grain boundaries and interphase boundaries.

Jan 1, 1989