Search Documents

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By Anthony K. Anyimadu, Chris M. Rule

Froth flotation is the primary mineral processing separation step employed in the beneficiation of PGM ore bodies. Anglo Platinum operates a significant portion of the total installed flotation capacity in the PGM industry, which is installed at 20 operating plants across the Bushveld. PGM flotation has undergone a considerable evolution in both the capacity of flotation cells employed as well as in the circuit design configuration over the past thirty years. Certain of Anglo Platinum?s flotation circuits have been in operation for a relatively long period of time, (in some operations installed equipment dates from the 1960?s) and this allows comparative operating performance between various equipment types and circuits to be evaluated. This paper summarizes some aspects of this experience. Research trends in flotation are continuously monitored to incorporate appropriate findings into existing and future circuit designs. Continuous evaluation and monitoring of flotation performance is undertaken to identify opportunities for increasing flotation efficiencies. Mineralogical and fractional analyses of plant composites and survey samples are analysed to interrogate speciation and association data. This analysis has enabled a better understanding of priorities and opportunities for improved metallurgical performance. These opportunities are divided into three improvement areas: stability, liberation, and fines flotation. The paper discusses these, as well as the circuit design improvements required to take full advantage of the opportunities identified.

Jan 1, 2007

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By D. Bessinger, H. Kotzé, J. Beukes

Keywords: Pyrometallurgy, furnace, ilmenite, smelting, Ticor Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and Mineral Separation Plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2 slag and 145 kt/a of pig iron.

Jan 1, 2006

By K. Thambi

The court in Baleni v Minister of Mineral Resources [2019] 2 SA 453 GP and [2020] 4 All SA 374 (GP), deliberated on the protection of rights of a community holding informal land tenure under Customary Law. The contention related to the necessary level of consent needed to acquire a mining right over such land. Moreover, whether consultations with such communities (Section 23, Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) or consent (Section 2, Interim Protection of Informal Land Rights Act, No. 31 of 1996 (IPILRA)) was required to acquire such right. The case has a significant bearing on the granting of mining rights in South Africa, and the discretion of the Minister of Mineral Resources (the Minister) in this regard. However, the objectives of the MPRDA and IPILRA do not dovetail, therefore consultation and consent are not mutually exclusive (Tlale, 2020). This note argues that, despite the resounding victory of this case, the peripheral basis surrounding the decision and the various levels of engagement require serious deliberation. Equally, the degree of reliance on the IPILRA requires clarity to avoid aborting the fundamental objectives of the MPRDA. This paper provides considerations and recommendations that may reduce or eliminate the tensions between the statutory and socio-economic rights in the application of the two statutes.

Sep 1, 2022

By N. C. Joughin

Potential for the mechanization of stoping in gold mines by N. C. JOUGHIN B.Sc. Eng., Ph.D. (Rand) (Member) The basic requirements for stoping machines are identified first by examination of the mining rates and productivities attained in conventional stoping, and then by examination of a series of problem areas associated with the shape of the reefs, rockbreaking, rockhandling, and the support and design of the machines. Some of the more important machines being developed are described briefly, and their principal features are compared with the basic requirements identified in the first part of the paper. An estimate of the potential demand for the different types of machines is given.

Jan 1, 1976

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

Newmont is one of the few remaining large mining companies that was established in the early nineteen hundreds. The company has a long, colourful and enviable history. This paper provides highlights of Newmont?s business and technical history since its inception in 1916, its transition to a ?gold only? company in the early 1990s and progress since that time up until the present day. Details of Newmonts current gold operations and its gold production profile for 2008 are also provided in the paper Over the last 50 years Newmont has developed a host of innovative gold technologies to meet the challenges of treating the complex refractory gold ores, found at the company owned mines in the Carlin region and around the world. Details of the technologies are provided and they include chlorination, roasting, bacterial and pressure leaching, leaching gold with thiosulphate and thiocyanate, N2Tech flotation, HPGR treatment of hard and abrasive ores and, finally, the use of Hydro-Jex technology for improving gold recovery from heaps.

Jan 1, 2009

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By V. H. R. Brereton

The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by V. C. H. R. BRERETON* (Visitor) This paper describes the discovery and recovery of gold, over a period dating back to the 1870s. on the farms Lisbon and Berlyn, situated approxim ately 1I km north-east of Pilgrims Rest. where mining ceased in July 1971. 99 years after gold was first discovered in the Pilgrims Rest and Sabie districts. Included in the paper are accounts of the discovery and mining operations of the Lisbon-Berlyn Company from 1884 to 1890. The operations of small companies and syndicates. the superficial winning of gold by diggers, and the encouraging reports of four mining engineers in 1890 are also mentioned.

Jan 11, 1973

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By I. Ashmole

From the point of view of the environmental impact created, dimension stone mining is a relatively benign industry. There are no emissions besides those of the diesel powered earthmoving equipment utilised in its extraction and a small amount of blasting gases. Contamination of water resources is only likely in the event of petrochemical spillages from storage facilities and equipment, and these can largely be either prevented or cleaned up effectively. The major environmental impacts are of a visual nature, while in sensitive areas, habitat destruction and the destruction of archaeological heritage may become significant impacts. The dimension stone industry has grown at an average rate of over 7% per annum since 1986, and is forecast to continue growing at this rate for the foreseeable future. The cumulative environmental impact of the industry will thus become more significant over time. This paper discusses the environmental impacts of dimension stone mining and recommends effective means for dealing with the practical aspects of reclamation and mine closure in dimension stone mining within the context of environmentally responsible business practices. The discussion focuses mainly on the operations of the Finstone Group in Southern Africa, which are considered to be world leaders in the application of environmental management within the dimension stone mining industry, although reference is also made to other situations which the authors have encountered at dimension stone quarries around the world.

Jan 1, 2008

By U. S. Kusel

Extractive metallurgy in Iron Age South Africa U. S. KUSEL, B.A. Hons. (Pta) (Visitor) The finds relating to the metal-working of Iron Age Bantu tribes are reviewed, the following metals or alloys being considered: gold, tin, copper, bronze, brass, and iron. Most is known about copper- and iron-working, but even this is very little, and no one has successfully been able to demonstrate how iron was smelted in the primitive furnaces that have been found.

Jan 1, 1974

A mineralogical study was conducted on the feed (3.51 g/t Au and ~90 g/t Ag) and four leach residue samples (assaying 0.09 to 0.19 g/t Au and 30.0 to 61.5 g/t Ag) from the Pinos Altos silver-gold deposit in Mexico to determine the cause for gold and silver losses. A comprehensive mineralogical and analytical approach including fire assay, gravity pre-concentration, ore microscopy, mineral liberation analyser (MLA) and electron microprobe was used for the current study. Results showed that gold and silver lost in the leach residues occurred mainly as inclusions in quartz and silicates (accounting for over 80% for Au and 92% for Ag of the head assays, respectively), with a minor amount in iron oxide and other minerals. The amount of liberated gold and silver is negligible. Results also showed that gold and silver particles in leach residues are mainly ranged from 1 µm to 5 µm in size, which implies that ultrafine grinding is required to improve the recoveries of these two metals. Keywords: mineralogy, gold deportment, silver deportment, silver-gold ore, leach residue, recovery improvement.

Jan 1, 2009

By G. Whittle

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction - primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007

By J. Meintjes

The measures taken by Rand Carbide Limited from the 1950s to 1976 to control dust emission from the electric furnaces at its Witbank factory are described. A new design of furnace for calcium carbide followed by a dry-fabric filtration plant for the furnace gases was not successful in arresting the dust. A 131 m chimney commissioned in 1968 effectively dispersed the dust-laden gases from both carbide and ferrosilicon production and so brought considerable alleviation. In 1974 a bag-filter dust-collecting plant was successfully commissioned on a 6 MV.A carbide furnace, and this was followed in 1976 by a bag-filter plant on a 46,5 MV.A ferrosilicon furnace. The company has spent considerable effort and money over two decades in trying to combat dust emission, but eventual success had to await technological development.

Jan 1, 1978

By H. J. S. Kriek

Methods are described by which increased production is achieved whilst retaining full availability of equipment and decreased refractory cost. Refractory materials have certain limitations, and when these limitations are known the variables in operating practice having the greatest impact on refractory life can be controlled. The most important factors to be closely controlled are porosity, chemical constitution of refractory materials, slag basicity, slag volume, FeO content of slag and temperature at which the process is operated. Knowledge of the process is invaluable in deciding on the type of refractory to be used. The types of refractories used in and the operating variables of the ironmaking, steel making and steel finishing units are described.

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By W. K. Loftus, H. S. Simpson

Discussion I. R. M. Cheston (Visitor): I should like to congratulate the authors on this interesting paper which graphically illustrates the overall effects of the gradual developments in diamond concentrating processes which have taken place over the past few years. These final stages of diamond concentration represent only a minor factor in the cost of diamond production but because of the shortage of highly trained people for this work, any easing of the burden on the sorting staff has an importance far beyond the immediate economic sphere. The search for the solution of problems posed by the economic and social conditions of industry is never-ending. The Diamond Research Laboratory is, even now, carrying out further work to improve still more the operation of general diamond recovery processes as described in the paper. Before looking at some of the latest developments in this field of final recovery, there are a few points arising from the paper on which I would like to comment. On page 321, reference is made to the X-ray sorters originally developed by the DRL. The paper gives a figure of 100 per cent recovery of diamonds from +7 mesh concentrates in two passes through the prototype machine. Not wishing to claim miraculous powers for our group, I would prefer to see this given as virtually 100 per cent recovery of all fluorescing diamonds. Firstly however much care is taken, there is bound to be an occasional operating loss. In the test work, 100 per cent recovery was made on many occasions but this was not always so. Secondly, although most diamonds fluoresce strongly under X-rays, some diamonds only fluoresce weakly. Type IIB diamonds, in fact hardly fluoresce at all, but the incidence of this special type of diamond is very low in most deposits. However, in operating the commercial X-ray machines, there is a certain background level of reflected radiation from other feed particles. Unless the diamond fluorescence is several times greater than this, it is not possible to achieve sufficient sensitivity in ejection. A certain small but variable proportion of diamonds from each deposit is always found to fluoresce too weakly to be recovered by the X-ray machine. Tests have shown, that for the De Beers mines, this proportion is considerably less than I per cent. These diamonds are nearly all dark brown or black in colour and therefore of low value. The degree of fluorescence does not, however, depend entirely on the colour or quality of the diamond and some of the brightest fluorescence comes from the lowest quality of boart diamonds. Investigations into the property of the diamond which causes this low fluorescence are being carried out. On page 322 it is suggested that zircon fluoresces in the same colour spectrum as the diamond. This is not quite accurate. The total light given out by zircon under X-rays is of the same order as that of diamond. However the zircon radiation has a much wider spectrum band than the diamond fluorescence. Reference is also made on page 322 to the effect of selective milling in small laboratory mills on diamonds. Perfect diamonds are very hard and very strong and are extremely difficult to break. Imperfect diamonds, which form the majority of diamonds recovered from most deposits, although hard, can be very brittle. Even under slight impact some of these diamonds may shatter to powder. Milling conditions must therefore be extremely closely controlled to minimize breakage, and even so, some breakage will always occur. As suggested in the paper, the necessary conditions are: the use of small balls, slow speed mills and very limited water addition. Tests elsewhere have suggested that the water content of the pulp in such a mill must be less than 25 per cent by weight of pulp to prevent diamond breakage reaching significant proportions. The skin flotation techniques described on page 323 operate on a very small scale. It is of interest to note that in West Africa a large-scale continuous skin flotation machine is used to recover the fine diamonds. In this operation the feed is dried and, after standing, is mixed with water and fed in a single layer onto a woven phosphor-bronze conveyor belt. This belt runs at a shallow angle into a water bath and as the particles are carried through the air-water-interface, the diamonds float off and over a weir into a collecting box. The bulk of the particles, being wettable, sink to the bottom of the tank and are continuously removed. If treated without prior drying, the diamond recovery is poor. If material is treated immediately after drying, a lot of the gangue particles also float. During standing, in the hot and humid atmosphere of West Africa, it is found that the gangue particles recover their wettability much faster than the diamond particles. Optimum selectivity is obtained after standing for approximately 24 hours. At the DRL we have been experimenting with optical filters to differentiate between the fluorescence of diamonds and zircon. By limiting the light transmission to the fairly narrow range emitted by diamonds, it is

Jan 4, 1970