Search Documents

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

An International Ferro-alloys Congress, arranged by the Ferro Alloy Producers' Association of South Africa, the South African Institute of Mining and Metallurgy, and the National Institute for Metallurgy, will be held in Johannesburg, South Africa, in April 1974. The technical programme, occupying five days, will cover the following topics in relation to all ferro-alloys: 1. Burden preparation, blending, pelletization, handling, reducing agents. 2. Electric smelting furnaces-design, operation, management,- smelting optimization, shop practice, refractories. 3. Mineralogy, reduction behaviour, smelting reactions, slags. 4. Automation, Pollution control. 5. Applications, trends in comsumption, trends in composition specifications. There will be no parallel sessions. Papers in the above topics are invited; review papers will also be welcome. Proposed titles and abstracts in not more than 200 words should be submitted before the 30th of November, 1972, to The Chairman, Programme Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa. The abstracts will be considered during January 1973, and papers accepted for the Congress must be submitted in final form before the 31st of July, 1973. The proceedings of the Congress will be published as a special volume. There will be a series of post-Congress tours to ferroalloy plants and other places of both technical and scenic interest. A full ladies' programme will be arranged. The First Circular, giving further details, can be obtained from: The Secretary of the Organizing Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa.

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

By A. P. L. Kotzé

This paper gives a brief description of the control measures used in the establishment of the Grootegeluk Coal Mine, near Ellisras in the Transvaal. Specific reference is made to the planning offunds, cost and financial control, and economic evaluation.

Jan 1, 1982

By M. W. John, I. D. Matthews

SYNOPSIS This paper describes the process adopted for the recovery of gold from a dump originating from clean-up operations at Durban Roodepoort Deep Gold Mine. The gold-bearing dump material was refractory in nature, not being amenable to cyanidation because of the high level of carbonaceous material present. The laboratory tests on the material involved particle-size and chemical analyses, a mineralogical examination of the material, preliminary tests, and optimization of the process for the treatment of the dump material. The preliminary tests included tests on roasting, flotation, pre-leaching, adsorbent-in-leach, and blinding. Of these options, carbon-in-leach showed the greatest potential. The rate of gold dissolution, the rate of gold adsorption by the carbonaceous material, and the ratio of carbon to pulp were then investigated. It was determined that the ratio of carbon to pulp necessary to yield a reasonable gold recovery resulted in a carbon loading that was not high enough for economic elution and regeneration. A process incorporating washing of the carbon with cold acid between adsorption cycles was tested, and reasonable gold recoveries and carbon loadings were obtained. Durban Roodepoort Deep Gold Mine piloted the conceptualized process and determined that it was economically feasible. Two Browns tanks on site were modified, and an acid-wash tank was installed. The capital outlay for the plant was recovered within some 3 months.

Jan 1, 1990

ENERGY 73 The First International Energy Exhibition will be held in Brussels from 13th to 18th May, 1973. Vllth INTERNATIONAL CONGRESS ON CYBERNETICS This congress will be held in Namur, Belgium, from 10th to 15th September, 1973. GRADUATE SCHOOL OF BUSINESS ADMINISTRATION University of the Witwatersrand The Sixth Executive Development Programme is scheduled to take place from 2nd July to 24th August, 1973. IFAC SYMPOSIUM 1973 Second announcement ofthe International Symposium on AUTOMATIC CONTROL IN MINING MINERALS AND METAL PROCESSING to be held at the University of New South Wales, Sydney, Australia, from 13th to 17th August, 1973. MINERALS AND ENVIRONMENT The effect ofthe mineral industry on the environment and mineral resources The Institution of Mining and Metallurgy, with the co-operation of the Institute of Quarrying and the Institution of Mining Engineers, will hold a Symposium "Minerals and the environment" at the Institution of Electrical Engineers, Savoy Place, from 4th to 7th June, 1974. COLLOQUIUM ON SLlMES DAMS The South African Institute of Mining and Metallurgy have great pleasure in advising members that a two-day colloquium on slimes dams is bei ng arranged for the 14th and 15th November, 1973. INTERNATIONAL SOLVENT EXTRACTION CONFERENCE This conference will be held at Lyon from 8th to 14th September, 1974. Particulars may be obtained from the Secretary: Dr A. Naylor, British Nuclear Fuels Ltd., Windscale and Carder Works, Seascale, Cumberland CA20 IPG, United Kingdom. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RIOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. Proceedings of the Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) The Proceedings of the APCOM Symposium held in Johannesburg from April 9th to 14th, 1972, have now been published. Members of the Institute may buy the Proceedings at a special price of R12,50 as against the list price of R25,00 to non-members. Verrigtinge van die Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) Die Verrigtinge van die APCOM Simposium, wat op April 9 tot 14, 1972, in Johannesburg gehou is, is gepubliseer. Lede van die Instituut kan die Verrigtinge teen 'n spesiale prys van R12,50 koop, in teenstelling met die prys van R25,00 vir nie-Iede.

By B. G. Fordyce, W. B. Parker

A description is given of the methods used in management planning, pit-equipment selection and maintenance operator training, and formal organization of mining personnel.

Jan 1, 1979

By X. Jia

The ability to perform three dimensional imaging at micron-scale resolution of real mineral floc sediments and structures using commercially available Micro X-ray Tomography (XMT) instrumentation can be used for the analysis of aggregates and granules, liberation and dewatering of sediments. This paper presents are view of recent work by the authors relevant to the mining and minerals industries. It covers three main topics: X-ray imaging of agglomerates and multi-component mineralic particles,, permeability of sediments, and dissolution of granules with potential application to heap leaching.

Jan 1, 2008

By P. R. Beeley

Metal founding - a modern perspective The recent development of metal founding is reviewed in the context of basic requirements for the successful manufacture of cil;5ti,ngs.Progress has been related to the two interdependent fields of process technology and product characteristics. . After a brief review of the growth of the traditional industry. various features of the modern industry are discussed. Reference IS made to current trends in process technology and to the introduction of new techniques affecting production engineering, product quality. and the general nature of the industry. Metallurgical aspects of metal founding are considered, and modern techniques for the control of casting conditions are examined. These aspects are related to the structure and quality of cast metal and to the development of newer types of cast material and product.

Jan 9, 1976

One of the largest and most exciting cast murals in the world has been erected in Johannesburg, forming the focal point of the large atrium in the new headquarters complex for Johannesburg Consolidated Investment Company Limited (JCI). Known as 'Rockface', this is waterwal1 structure formed of cast stainless-steel panels

Jan 1, 1986

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By I. H. Clark

A variety of backfills is presently being placed in different gold mines. The backfills are pumped as slurries to stopes where they are discharged into some form of retaining paddock. The effectiveness of fill as a support medium will depend on a number of factors. These can largely include (i) inherent properties of the material, e.g. particle size, shape, distribution and com- position, and (ii) conditions of placement. The terminology required for describing backfills is introduced, and the various laboratory-measured properties are presented for a variety of fills. Finally, the properties of the fills as they are placed underground are discussed.

Jan 1, 1988