Search Documents

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By Luthie Els, Chris Coetzee, Roedolf Koekemoer, Casper Els, Olof Vorster, Frank Fereday

Three electric arc furnaces (EAFs) were constructed by Union Carbide at Tubatse Ferrochrome (TFC) in1975. This plant was expanded to four furnaces at the East Plant in 1985 and the gas cleaning system was enlarged without taking flow dynamics into consideration. In order to improve competitiveness, TFC has increased furnace capacity, partially substituted coal for coke, and changed the charge mix. These changes increase the heat and dust load into the air pollution control (APC) system. TFC embarked on a project to improve the APC capacity by: ?Quantifying the required off-gas capacity ?Optimising the aerodynamic flow through the system by means of Computational Fluid Dynamics (CFD) ?Converting the old Brandt Koyo top entry baghouses to bottom entry ?Upgrading the cleaning system ?Installing Gore-tex® ePTFE membrane filter bags The estimation of required off-gas capacity is traditionally done by rule-of-thumb methods such as specific extraction. A more elegant evaluation method was developed for simulating the effects of changes in charge mix on the furnace reaction gas volume and the APC system. Reaction gases are calculated by modelling the reactions taking place in the furnace and off-gas volumes are compared to both fan and baghouse capacity. This enables identification of bottle-necks in the off-gas system. CFD techniques were utilized to evaluate geometric imbalances and propose solutions to ensure optimal use of off-gas capacity. The system modifications were completed over several months and the modified equipment went into service in May2006.

Jan 1, 2007

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By K. Barani, S. M. S. Ganji

Creatine was used as a lixiviant for gold dissolution from gold ore. The effects of creatine concentration, temperature, leach time, and pH were examined for their influence on extent of gold dissolution. The results show that at a temperature of 75°C and pH 11.5, gold dissolution increased from 51% to 88% on increasing creatine concentration from 25 to 50 g/t. Further increase in creatine concentration showed a negative effect on the gold dissolution. Gold dissolution increased from 47% to 87% by increasing the temperature from 25°C to 55°C, and from 61% to 89% by increasing pH from 10 to 11.5. Under the optimum conditions of solids’ content of 30%, pH 11.5, creatine concentration of 100 g/t, temperature of 75°C, and hydrogen peroxide addition of 2%, about 90% of the gold could be dissolved from the ore after 24 h. A comparison between creatine and cyanide leaching showed that 90% gold dissolution was achieved at a cyanide concentration of 300 g/t, which is three times higher than the creatine concentration under optimal conditions.

Apr 14, 2024

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By M. S. M. Aljuhani

In this paper, one of the human factors that affect productivity in an underground gold mine in Saudi Arabia was investigated and analysed for the purpose of improving productivity. The human factor that was investigated is labour utilization and labour productivity. In the selected mine, labourer?s performances were measured carefully. It was found that in this mine, workers spend only 65% of the shift time in a productive work, and they spend 35% of the shift time in non-productive activities. As a result, recommendations were presented to enhance productivity in the selected underground gold mine by enhancing labour utilization.

Jan 1, 2002

By B. McFadzean, N. Patterson, M. Becker, S. Geldenhuys

The retreatment of secondary tailings for platinum group metals recovery presents a range of potential challenges, which vary depending on the nature of the original ore and the type of pretreatment it was subjected to. These challenges include the prevalence of ultrafine particles, which promote slimes coatings on valuable minerals, hinder bubble-particle attachment, increase pulp viscosity, and lead to higher gangue entrainment; surface oxidation of minerals, which alters their floatability; and the presence of deleterious gangue minerals and residual platinum group metal species that are inherently difficult to recover by flotation. This study compares the batch flotation performance across a range of tailings samples from the eastern and western limbs of the Bushveld Complex. A complementary mineralogical analysis was conducted to gain deeper insights into mineral behaviour. The paper evaluates these findings to identify the key factors contributing to poor platinum group metal performance.

Mar 6, 2026

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025