Search Documents

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By J. C. Barry, J. H. van Laar, P. L. Crouse, H. Bissett, I. J. van der Walt

"Plasma-assisted spheroidisation of metal powders offers several technical advantages with respect to both the ease of materials handling and powder-metallurgical item manufacturing. Advantages include improved flowability, increased powder packing density, elimination of internal component cavities and fractures, changes in morphology resulting in decreased friction between particles and contamination during pneumatic transport and enhanced particle purity. In this empirical study, spherical iron particles were produced using a microwave plasma operating at atmospheric pressure and characterized using optical microscopy and SEM techniques. Iron powders were fed into the system at fixed operating conditions, resulting in particles with spherical structures. The theoretical estimate of the time required for melting to occur is 1.6 ms, an order of magnitude smaller than the actual residence time. IntroductionParticle design and functionalization has become an increasingly popular aspect of materials synthesis and powder-metallurgical item manufacturing. One such technique involves the spheroidisation and densification of feed materials, typically in the form of chemical powders with wide particle size distributions. The major benefits of powder spheroidisation include improved powder flowability, increased powder packing density and powder purity, reductions in internal voids and defects, as well as the ability to manipulate the particles surface morphologies (Boulos, 2004). Thermal plasma processing has the potential for scale-up and for producing industrial quantities of spheroidised powder.Thermal plasma technologies offer a wide spectrum of material synthesis and treatment options, amongst others the synthesis and spheroidisation of nano-sized ceramic and metal particles (Kumar and Selvarajan, 2006). The spheroidisation process occurs within the plasma discharge via in-flight heating and melting of the powder feed material, given high enough plasma temperatures (Fridman, 2008, p. 495). Surface tension in the molten droplets results in spherical, or nearly, spherical, powder particles being formed upon exiting the plasma discharge where the droplet undergoes rapid cooling and freezes. Quite often, the bulk density of these spherical particles is higher than that of the starting material (Boulos, Fauchais and Pfender, 2013, p. 42). The different plasma spheroidisation techniques reported include radio frequency (RF) induction thermal plasmas (Jiang and Boulos, 2006; Karoly and Szepvolgyi, 2005; Yuming, Junjie and Yanwei, 2013), nontransferred direct current (DC) thermal plasmas (Chaturvedi et al., 2014; Kumar and Selvarajan, 2008; Suresh, Selvarajan and Vijay., 2008) and microwave-assisted plasma processing methods (Chen, Gleiman and Phillips, 2001; Vanamu et al., 2004; Weigle et al., 2004)"

Jan 1, 2016

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African coal discards derived from feed coal for thermoprocesses pose human health and environmental problems and incur high disposal costs. These issues need to be resolved. Coal fines and a coal fines/ K2CO3 blend were combusted at 700°C in a laboratory rotary kiln to produce ashes containing metakaolinite (Al2O3.2SiO2) and illite/muscovite/orthoclase amorphous materials. The blend ash and coal fines ash, containing 18% K2O and <1% K2O respectively, were leached with water and with 1 M and 8 M NaOH at 80°C for 4 hours using a solid to liquid ratio of 1:5. The 8 M NaOH leach yielded 17% sodalite (Na8Si6Al6O24(OH)2) formation through SiO32-, Al(OH)4-, and Na+ precipitation in the leached ashes. The 1 M NaOH leach yielded no sodalite. X-ray fluorescence analysis of the original ashes and leached ashes showed low Al and Si dissolution efficiencies due to the sodalite formation. Sequential NaOH leaching resulted in the highest potassium dissolution efficiency of 89% for the ashes of fines/K2CO3 blend and 59% for the fines. It may be possible to increase the ash-derived zeolite concentration by using even higher NaOH concentrations (12–20 M NaOH) during leaching. Sodalite derived from coal ash could possibly be utilized for water purification in industrial applications, or as molecule separators. The potassium-containing liquid could be used in fertilizer manufacture.

Mar 30, 2023

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By H. W. J. P. Neomagus, R. K. K. Mbaya, J. R. Bunt, N. T. Leokaoke, N. W. Makgobelele

Silicon Smelters consumes more than 80000 t/a of wood-derived charcoal as carbonaceous reductant in the production of silicon metal. More than 10% of this material is discarded as fines (<6 mm) generated due to abrasion during processing. Charcoal fine residues (<650 μm) and polyvinyl alcohol (PVA) binder were used in this study to produce mechanically strong charcoal briquettes for metallurgical application as carbonaceous reductant. The PVA binder was added in mass percentages of 1, 3, and 5 wt% to the charcoal fines. The compressive strength, abrasion resistance index (ARI), drop shatter resistance (SRI), and water resistance index (WRI) were measured as functions of curing for up to 7 days under atmospheric conditions, and the results compared with metallurgical grade coarse charcoal. The ash content of the produced briquettes was found to be high (6.6–8.0%) compared with the coarse charcoal (1–3%). The 3 and 5 wt% PVA-bound briquettes were found to be the strongest, with compressive strengths of 40 and 115 kg/cm2 respectively, with WRI values of 75 and 73% respectively. The produced briquettes were found to have lower ARI and SRI values compared to the coarse charcoal. Future work should include beneficiation of the fine charcoal discards prior to briquetting, and an increase in binder addition to above 6 wt% to improve the ARI and SRIn.

May 1, 2021

By C. Tokoro, T. Kato

The objective of this study is to improve the shrinking core model for particles with a particle size distribution and clarify the activation mechanism of rare earth elements dissolution by mechanochemical activation. To achieve this objective, the method, called the doubly integrated micromodel, was applied for a shrinking core model in this study. This method consists of integrating the batch leaching rate of a single particle over the distribution of both feed particle size and reactor residence time to arrive at the fraction unleached. The usefulness of the shrinking core model improved by doubly integrated micromodel was confirmed by comparing it with a shrinking core model. To apply the shrinking core model improved by doubly integrated micromodel to rare earth elements dissolution from weathered residual rare earth ores by mechanochemical activation, leaching experiments were performed for grinding samples by planetary ball milling. The reaction equation of mechanochemical reaction by planetary ball milling for weathered residual rare earth ores was investigated by x-ray absorption fine structure analysis. As a result of a kinetics study, the rate-determining process of leaching changed from reaction to diffusion reaction control by planetary ball milling. Based on these results, it was revealed that the main mechanism of activated rare earth elements dissolution from weathered residual rare earth ores was a mechanochemical reaction by planetary ball milling. Keywords: Mechanochemical reaction, particle size distribution, shrinking core model

Jan 1, 2020

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019

By Y. Fan, D. H. Zhang, J. Y. Xu

The hydrogeological conditions in the Chambishi mine area in Zambia. were investigated. Chambishi is a very wet mine and groundwater discharge costs are high. The research goal was to identify methods to reduce the discharge costs without greatly affecting the mining process. Hydrogeological data was obtained from measurements in drill-holes and from drill cores. The differences in structural deformation in different areas determine whether a layer of rock is an aquifer. In the mine region, the Lower Roan Group ore shale and quartz-sandstone unconformably lie on the basal schist and granite aquifuge. The Upper Roan Group dolomite is continuously distributed over a large area around the orebody. This dolomite is the main target of groundwater control efforts, and its water yield is also influenced by the deformation intensity. Based on the observations, backfilling was gradually adopted to appropriately safeguard the integrity of the aquifuge above the orebody. The overlapping relationship between the aquifer and aquifuge has been utilized to increase mine drainage efficiency. This measure has not only greatly reduced the costs of mine drainage, but also improced protection of the groundwater environment. The old drill-holes that were not sealed after exploration drilling were grouted. Further, possible water-conducting fracture zones were investigated. Cover drilling towards the suspected zone was conducted to prevent the high-pressure groundwater from shallower aquifers from entering stopes in deep areas of the mine.

Jun 10, 2024

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By H. S. Marshall

Optimum Colliery is an opencast strip mine producing 18Mt of bituminous coal per annum for the export and inland markets as well as for domestic power generation at the Hendrina PowerStation. Coal is exposed by four 60m3 and four 11m3 walkingdraglines and transported from the open cuts to the processing plants by twelve 130 ton coal haulers. Overburden and interburden areas are drilled by nine 250mm-diameter rotary drill rigs. Until 1997 all surveying tasks were conducted by electronictotal stations requiring accurate control points from which line-of-sight XYZ readings could be taken. In 1997 a GPS system was introduced which consisted of a fixed base station and two rovers. The rovers were able to perform most of the survey tasks assigned to total stations. In addition, two overburden drills were equipped with blasthole drill navigation systems, which includes the drill monitoring and material (strata) recognitions system. The rest of the drilling fleet will also be equipped with GPS systems. Blasthole positions are designed in the office based on survey and geological/geophysical information and transmitted via radio link to an industrial PC on the drills. Together with GPS positional data, both the planned and actual drill positions are displayed on an LCD screen. This eliminates the need for surveyed hole positions to be staked before drilling, and for actual hole positions to be surveyed after drilling. As holes are drilled, performance and rock property data transmitted back to the office. Future applications will include GPS monitoring of dragline positions and pad elevations. GPS receivers on the draglines will utilize the existing base station to calculate and transmit XYZ co-ordinates. Another application will be locating of boreholes in the field prior to the pumping of specified explosive charges into the blastholes. Charging instructions for each blasthole will be loaded into the computer on the explosives truck which will be equipped with a GPS system for hole identification.

Jan 1, 1998

The following comment has been received from Mr A. D. Osche* on the above paper, which was published in the Journal in October 1977 (vol. 78, no. 3, pp. 51-62). Obituary: T. K. Prentice The Institute records with deep regret the death on 30th January of its senior surviving Past President, Mr Thomas Kennedy Prentice, at the age of 83. Book reviews R. A. Rich, H. D. Holland, and U. Petersen. Hydrothermal uranium deposits. (Developments in Economic Geology, vol. 6). Amsterdam, Elsevier Scientific Publishing Co., 264 pp. with 77 illustrations and diagrams, 30 tables. U.S. $34,75. M. David. Geostatistical ore reserve estimation. Amsterdam, Elsevier Publishing Company, 1977. 364 pp. World mineral industry The Australasian Institute of Mining and Metallurgy is celebrating its sesquicentenary in 1979. A conference will be held in Perth from 13th to 18th August, 1979, as part of the celebrations, the theme being &apos;Australia&apos;s Role in the World Mineral Industry&apos;. Engineering teaching staff UNESCO has extended its technical assistance to the Venezuelan government in the training of engineers to suit the rapidly developing economy of the country. UNESCO vacancy Vacancy for a post of expert under the UNDP. (1) Title of post: Expert in metallurgical engineering. (2) Duty station: Instituto Universitario Politecnico of Ciudad Guyana (Venezuela). Shell Design Awards The annual Shell Design Awards, organized by the Design Institute and sponsored by Shell South Africa (Pty) Ltd, focus attention on achievements in South African design.

Jan 1, 1978

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By L. S. Linda, P. G. H Pistorius

Ferritic stainless steel is utilized to fabricate automotive exhaust systems using a ferritic weld metal. Ductility of the weld metal is higher if its microstructure contains a significant proportion of equiaxed grains. The formation of equiaxed (rather than columnar) grains is favoured by a higher titanium weld metal content. In this study, the Ti content of ferritic stainless steel weld metal was changed by using Tifree (Type 436) and Ti-containing (441) ferritic stainless steel as base metals. The metal-cored welding consumable contained 0.4% Ti. Gas–tungsten arc welding and gas–metal arc welding processes were compared. The weld metal Ti content ranged from zero to 0.5% Ti, as determined from scanning electron microscopy supplemented by inductively coupled plasma optical emission spectroscopy. Cross-sections of the weld beads were subjected to point counting (to estimate the fraction of equiaxed grains) and image analysis (to estimate the average grain size). Point counting proved to be more reliable. The fraction of equiaxed grains was sensitive to the Ti content, but not to the welding process. Below 0.4% Ti, the fraction of equiaxed grains gradually increased with an increase in the weld metal Ti content; above 0.4% Ti, the fraction of equiaxed grains rapidly increased with increasing Ti content. The transition in behaviour at 0.4% Ti corresponded to a Ti content at which Ti-rich precipitates became stable at the estimated liquidus temperature of the weld metal.

Jul 2, 2022

By D. Menne

An empirical dimensionless correlation is presented that relates system variables to the superficial slip velocity between solid mineral products and an interstitial fluid. The correlation is valid within engineering accuracy for all solids and fluids at all concentrations. The particular usefulness of the correlation is that it provides explicit equations for both slip velocity and voidage.

Jan 1, 1983

By P. C. Pistorius, M. P. Maphutha, J. D. Steenkamp

Advanced high-strength steels (AHSS) are sophisticated materials being developed by the steel industry to mitigate challenges related to the performance of motor vehicles. To meet the requirements of AHSS, the ferromanganese alloys (FeMn) utilized in the production of the steel are required to contain acceptable levels of unwanted impurities, i.e. P, S, N, H, and C. The focus of the current study was to investigate dephosphorization of ferromanganese to produce a low-P alloy that could be effectively utilized in the production of AHSS. The study involved conducting laboratory-scale testwork to study the efficiency of CaO-based slag systems to dephosphorize FeMn alloys. The addition of Na2O, CaF2, and BaO to MnO-CaO-SiO2 slag was considered. The test work was carried out in a 25 kW induction furnace at temperatures of 1350°C, 1400°C, and 1450°C. The P partition coefficient (Lp) remained small at <1, which is an indication that dephosphorization had not been achieved. The baseline slag, comprising 40%CaO-40%SiO2-20%MnO, reported higher Lp values. Addition of Na2O and CaF2 did not show any further benefit. Substituting half of the CaO by BaO, resulted in similar Lp values to those of the baseline slag under conditions of 1350°C and 1450°C at 30 minutes. In summary, based on the Lp values obtained, the conditions investigated with the CaO-based slags appeared to have been unfavourable for dephosphorization of FeMn alloys, as most of this impurity element remained in the alloy.

Sep 1, 2021

By H. Aykul

The choice of which mining method to use at many large surface coal mines is often dicated by what machinery is available or what experience the mine management can offer. One of the most significant surface coal mines in Turkey is owned and operated by the Turkish National Coal Board, located to the west of the city of Kütahya. The Seyitömer Lignite Enterprise (SLE) extracts low quality coal, the majority of which is supplied to an adjacent power station. The coal seems at SLE contain bands of ash which under normal mining conditions are extracted with the coal. This increases the ash content of the run of mine coal and results in lower efficiency at the power station and financial penalties for SLE. In this paper, therefore, selection of the best possible equipment and production method was identified to achieve high selective mining at SLE. The research found that two different high selective mining methods were suitable for selective excavation of the B3 seam, which were hydraulic excavator and truck and surface miner and truck combinations. It was also found that high selective excavation could provide the desired coal quality at 52% lower costs when the whole process (excavation, transportation, processing, etc.) was considered. Keywords: coal mining, surface mining, selective mining.

Jan 1, 2007