Search Documents

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

Book reviews Jones, M. J. (editor). Process engineering of pyrometallurgy. Proceedings of a joint meeting of the Institution of Mining and Metallurgy and the Institution of Chemical Engineers. London, Institution of Mining and Metallurgy, 1974. 105 pp. £6,50. Nim reports Report No. 1656 The analysis of geological samples for trace elements by direct-reading emission spectrometry. Report No. 1669 An assessment of the carbon-rod atomizer for the determination of silver.

Jan 12, 1974

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

DISCUSSION: The value of incentive payments in the mining industry by K; SMITH Published in the Journal, May 1974 H. P. CARLISLE* The author has drawn attention to one of the most important of mining problems, viz productivity, and in so doing has highlighted, perhaps inadvertently, the difficulty of assessing productivity. Competition for Students Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Corrigendum The Journal, May 1974, p. 377 We regret that the last portion of A. A. Hazell's contribution to the paper 'The value of incentive payments in the mining industry' by K. Smith was printed in the wrong sequence.

Jan 10, 1974

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004

By E. Mpoloka

Debswana together with ADP as their design partner have embarked on an RDP project at Jwaneng Mine. The objective of the project is to install a 2 million ton per annum mineral processing plant that will fast track the recovery of diamonds from the Debswana tailings resource to ensure maximum return on investment for the company. Due to the prevailing economic conditions Debswana has had to review the way they used to build plants in the past and consider simple, fast and effective ways of doing things. The rapid deployment plant concept is therefore the most suitable means of achieving this objective. Debswana is also considering an operating partner who will operate far more efficiently and cheaply compared to the larger more cumbersome and less agile Debswana.

Jan 1, 2010

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By A. M. Sage

This paper reviews the metallurgical functions of vanadium in high-strength Iow-alloy steels, and discusses the ways in which vanadium is used in various types of steel supplied as reinforcing bars, plates, sections, and strip. Potential developments to meet new engineering requirements are discussed briefly.

Jan 1, 1984

By A. J. Raubenheimer

The most important criteria in the selection of mining equipment (mining conditions. operational performance, engineering design, manufacturer's involvement, and financial considerations) are discussed in turn. Some mention Is made of the equipment population In South African collieries. and it is pointed out that both the manufacturer and the mine operator should take due cognizance of future trends in equipment.

Jan 1, 1983

This list of corrosion-related terms was compiled to encourage the use of the correct terminology, and to serve as a handy reference for students. It Is based on a similar list compiled by the National Association of Corrosion Engineers (NACE). To promote bilingualism, the Afrikaans terminology is included (in italics at the end of each entry).

Jan 1, 1991

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

A Colloquium and General Meeting was held jointly with the Mine Ventilation Society of S.A. in Kelvin House, Johannesburg, on 17th November, 1971, the theme being "The Economics of Mine Ventilation". Professor D. Howat (President) was in the chair. The Colloquium was attended by 150 delegates and was opened by the President at 9.00 a.m. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following Grades: Fellows: Frederich-Wilhelm Volk, Peter Bennet Columbine. Members: Allan Colin Lawrence, Karel Anton van Gessel, Christopher Robert Harrison, Christopher Michael George Wartley, Frank Heinrich Deist, Ralph Morris, Benjamin Johannes Nolte. Associates: Wolf gang Freidrich Gottsman. TRANSFERS From Member to Fellow: Hugh Edward Keith Alien. From Graduate to Member: Errol Vincent Bosman, Christopher Roderick Stewart Needes, Bernard Wessels Holthousen. From Student to Graduate: David Robert Fleming. I welcome the new members to the Institute and congratulate them on their election. CO-OPTION TO COUNCIL The President announced that at the Council meeting held on 5th October, 1971, it was agreed, in terms of Rule 3.9 to co-opt Dr T. B. Beeton to Council. COLLOQUIUM The President welcomed visitors and members. He stressed that the discussion would be informal and that any contributor requiring publication should submit his contribution in writing. He then thanked the authors for providing pre-prints of the papers. After the President had concluded his opening remarks, he asked Professor J. de V. Lambrechts to act as Colloquium Chairman for the day and he, in turn, introduced the three Session Chairmen namely, Dr A. Whillier (Chamber of Mines and President of the Mine Ventilation Society); Mr M. Barcza (Managing Director, Corner House Laboratories); and Mr L. W. P. v.d. Bosch (Chief Consulting Engineer, Union Corporation). The following papers were presented: "Fan efficiency investigation on mines of the Union Corporation, Ltd." by J. A. Drummond. Published in the Journal Feb. 1972. "The design of underground cooling towers" by A. Whilliel&apos;. Published in the Journal, Oct. 1971. "Some aspects of the design of cooling plant installations" by R. Hemp. Published in the Journal, Nov. 1971. "The planning of ventilation and refrigeration requirements in deep mines" by D. F. H. Grave and R. M. Stroh. Published in the Journal, Dec. 1971. "Cooling power of underground environments" by D. Mitchell and A. Whillier. Published in the Journal, Oct. 1971. At the conclusion of the three technical sessions the Symposium Chairman commented as follows, indicating that he would prepare a written summing up at a later stage: "The tone of the colloquium has had a sincerely practical note about it. It would have been a pity if the ventilation experts talked only theory and little practice. This practical theme has, I am sure, made the colloquium interesting to both ventilation men and others whose daily tasks do not touch so closely on this fascinating subject. This practical theme was in evidence through all the papers and contributions. Some of you may have felt that there was not enough emphasis on the word &apos;economics&apos; as advertised in the broad title of the colloquium. I do not think this was really a valid criticism because as someone said &apos;it all boils down to Rands in the end!&apos; So whether it was a case of low fan efficiency, poor design of cooling towers, wrong planning or low human efficiency due to high heat stress. . . it all boils down to money saving and therefore economics, whenever improvements are forthcoming. The title of the colloquium was thus not misplaced. The views of senior mining men on the production side are appreciated. Let us say that this exchange of views between ventilation engineers and those who have to take the final decisions and spend the money, should prove to be most rewarding." Professor Lambrechts finally thanked the Session Chairmen and everybody who had helped to make the colloquium a success and the meeting closed at 4.0 p.m. In a subsequent written summing up, the Colloquium Chairman gave the following as his impressions of some of the highlights which emerged from the papers and discussion thereof: (The names indicate the authors only). Drummond: It was hinted that the time had arrived to consider the introduction of a South African fan test code which would be better suited to local conditions than the currently acknowledged B.S.S. code which, however, is seldom enforceable in practice. In this connection also, there was prominent reference to the thermodynamic approach of McPherson. Wide variations in the quality of maintenance of, and repair work on, fans were stressed. It was mooted that ventilation engineers responsible for estimating the basic duty specifications for large fans, frequently played safe by overestimating the pressure required, thus ensuring that there would not be a shortfall in air volume delivered. This usually meant reduced fan efficiency and it was suggested that decision makers seemed to lay more emphasis on volume of air delivered than on real eco-

By S. Ranganathan

Production of ferro-chromium in the submerged-arc furnace is highly energy-intensive. Several process rates have been attempted to reduce the specific energy consumption in the production of this alloy. An exhaustive understanding of the thermo-chemical features of the production process can be used to reduce the specific power consumption significantly. The knowledge can be used to reduce the energy drain through undesired reactions in the process can be minimised. Plant trials have shown that specific energy consumption up to 100kWh/tonne of hot metal can be obtained by adopting this strategy. The process requires modification in operation practice and does not require any capital investment unlike other processes adopted for reducing power consumption. The principle of thermo-chemistry involved in this process development and results of plant trials are discussed in detail.

Jan 1, 2007

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003