Search Documents

By L Tolmay, L Nair

Investor confidence can be compromised when one observes large discrepancies between the SAMREC reserves and the mining plan. It is therefore up to the responsible persons to ensure that all contributing factors get taken into account when determining a reserve declaration. Confounding factors could be further aggravated by large oscillations in the commodity price thus resulting in major changes to the mining plan, if the accepted price was either too optimistic or pessimistic. Additional factors that must receive our attention are, uncertainty in geological facies type, mining practices, geology and grade estimation. The paper outlines (in the authors? opinion) some of the important factors that need to be taken into account, in order to ensure proper alignment between the estimates of the life of mine (LOM) reserve grades, and the corresponding actualisation of the mining plan. These parameters provide an historical insight into what actually happens when attempts are made to implement the mining envisaged in the LOM plan. In turn these allow judicious application of discount factors that enable a realistic estimate of SAMREC reserve classification and declaration. Some of the factors that will be covered are: - 1) Flexibility of developed reserves and the ability to maintain this. 2) Mining control mechanisms and their overall efficacy. 3) The ability to extrapolate facies types and its effect on grade control. 4) The ability to control the mining mix and value variation. 5) Finding a happy medium between optimism and pragmatism.

Jan 1, 2007

By N. Hamlef

In this study, the effects of heat treatment on phase formation and surface morphology of the Cr-Pt coated system are investigated using X-ray diffraction and electron microscopy techniques. The CrPt andCr4Pt (Cr3Pt - A15 type) phases were formed after heat treatment of the coated samples. Heat treating at 1000°C renders a distinct island coating morphology that is non-continuous in nature. A diffusional model is proposed for this coated system with regards to the surface morphology formation after heat treatment.

Jan 1, 2014

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By T. M. Chagwedera, A. E. Lewis, J. Chivavava

Eutectic freeze crystallisation is a novel separation technique that can be applied to treat brine solutions such as reverse osmosis retentates, which are often a mixture of different inorganic salts. The treatment of calcium sulphate-rich brine solutions through eutectic freeze crystallisation has resulted in gypsum scale formation on the walls of the crystallisers and ancillary equipment. In order to prevent gypsum scaling on equipment surfaces, it is essential to understand the mechanism of gypsum scaling on cold surfaces. This paper focused on the interaction between gypsum crystallisation in the bulk solution and scaling on the crystalliser walls in the presence of gypsum seeds. A cooled, U-shaped stainless-steel tube suspended in the saturated solution was employed as the scaling surface. Preliminary results showed that the scale layer was predominantly composed of needle-type and hexagonal prismatic crystals. The rate of scale deposition was highest during the first 24 hours, thereafter it decreased. A thin scale layer was observed to have coated the tube within the first hour of the experiment. Seeding, using reagent grade gypsum crystals, was effective in reducing scale layer formation through providing a surface for growth. The highest scale reduction, 81%, was realised at a seed loading of 0.50 g/L. At a high seed loading of 4.01 g/L, the seed material adhered to the tube. Keywords: Gypsum, eutectic freeze crystallization, seeding, scaling, cooling crystallisation

Jan 1, 2020

By N. C. Joughin

Progress during the last two years in the Chamber of Mines programme for the development of mechanized stoping methods is reviewed, and advances in the basic technology are outlined. Specifically. advances in the understanding of rock fracture around stope faces. in rockbreaking techniques, in rockhandling techniques, and in engineering are described. The state of development reached with mining systems based on cutting, impacting. and blasting is also described.

Jan 1, 1978

By J. Kunze, R. Degal

During the last 100 years, the submerged arc furnace has been one of the most amazing diversified melting units. These furnaces have found their application in more than 20 different main industrial areas such as iron, ferro alloy, chemical industry, lead, zinc, copper, refractory, titanium oxide, recycling, phosphorus etc. Such an evolution was only possible because of tremendous efforts in research and development and due to the large range of design solutions. The worldwide strong competition also forced the industry and plant suppliers to develop highly efficient, economically balanced units in optimized sizes and with long lifetimes, to adapt to the market conditions. Regarding the environment, the plants improved significantly in terms of water treatment plants and off-gas treatments as well as on site recycling units. This paper will give a short overview regarding the history of the furnace and the latest developments in today?s main application fields: ferro alloys, non-ferrous, special application and recycling. In addition new activities in research and developments are briefly discussed.

Jan 1, 2004

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By S. Botes, H. van der Merwe

While the refractory lining contains the process on a steady-state basis, the tap-hole must provide a channel for transport of molten materials at discreet intervals, with thermal cycling as routine. The tap-hole introduces a discontinuity in any lining, and this fact can lead to failure in the region around the tap-hole before general lining failure occurs. Hence there is a need for a rapid and reliable tap-hole repair technique that can be readily implemented in conjunction with all types of linings. The UCAR®V Repair supplied by GrafTech is a durable solution capable of repairing all types of lining designs and has been extensively utilized in the ferroalloy industry. More than 20 UCAR®V Repairs have been successfully performed in South Africa alone. This paper describes the system in general and reviews recent repairs and their unique challenges.

Jan 1, 2014

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By E. Kapilashrami, S. Seetharaman

Refractory/metal interactions and associated reactions are significant during casting as they can lead to inclusion formation. High-temperature interactions between aluminosilicate refractories and molten steel were studied in the present investigation using the sessile drop method. The changes in the contact angles between molten iron with well-defined oxygen levels and substrates of silica, mullite (3Al2O3?2SiO2) as well as commercial refractories were measured in the dynamic mode. In all cases, the reaction led to slag formation. The experiments were performed under isothermal conditions at 1823 and 1873 K. A known and constant oxygen partial pressure was imposed above the iron drop, through appropriate CO-CO2-Ar mixtures. For all substrates, the contact angles started decreasing due to the lowering of the surface tension of iron, as oxygen was imposed on to the system. When a critical level of oxygen was reached, slag started forming at the drop/substrate interface and at this stage, the contact angle dropped suddenly. Subsequent behaviour of silica and mullite was observed to be different, with SiO2showing a non-wetting behaviour. In the case of SiO2substrate, there were also deep erosions along the periphery of the drops and there was slag accumulation at the sides of the metal drop, probably due to Marangoni flow and/or SiO(g) formation. SEM and EDS analysis of the substrates revealed that the formed slag was fayalite. The thermodynamic criteria for slag formation and possible mechanisms of the reaction are discussed in the light of the experiments. Key words: silica, mullite, fayalite, corundum, slag formation, sessile drop.

Jan 1, 2004

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By B. C. Alberts

Rapid and effective handling of run-of-mine, waste, and treated materials is vita.! to every step of resource development and recovery. Modern mine managements have planned and engineered systems for the handling of ever-larger tonnages. Where traditional methods have not proved to be costeffective and adequate, managements have pioneered the development of new materials-handling systems in the mining industry.

Jan 1, 1983

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020