Search Documents

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By B. K. Loveday

The South African Institute of Mining and Metallurgy hosted a School on 'The Practical Design of Comminution Processes' at Megawatt Park (near Johannesburg) on 14th to 16th May, 1991 Derek Barratt, a Senior Consultant of Wright Engineers, Canada, and the main speaker, provided a good insight into how Wright Engineers design milling circuits, particularly large semi-autogenous mills. He was ably assisted by Jens Lichterof Allis Mineral Systems, who described some interesting examples of pilot-plant testwork and summarized South African milling practice. Mike Moys of the Witwatersrand University spoke on the influence of pulp viscosity on mill performance, and Johan Engelbrecht and Jeremy Bosman of Multotech

Jan 1, 1991

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

Mr Colin M. Spence took office as President of The Federation of Societies of Professional Engineers on 1st July, 1984. Colin Maynard Spence was born in November 1921, and was educated at the Durban Preparatory and High Schools, in both of which he was a Dux Scholar. He graduated from the University of Natal in 1942 with a B.Sc. degree in civil engineering. In 1958 he received a Diploma in Town Planning from the same university. Cessation of Membership In accordance with Clauses 7.6.1 and 12.1 of the Institute's Constitution, Rules and Policy, the following members have been struck off the Membership list.

Jan 1, 1984

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

By R. D. Cromarty, J. Du Toit

"Penetration of matte into tap-hole bricks causes detrimental refractory wear, which can lead to furnace breakouts. The ability of the tap-hole clay to form a protective layer on the brick, thereby limiting matte penetration was investigated by examining the interaction between platinum group metal (PGM) matte, tap-hole clay, and alumina-chrome refractory bricks on a laboratory scale.Samples containing clay and brick as well as samples containing clay, brick, and matte were heated to different temperatures to establish the clay-brick interaction and the extent of matte penetration. The greatest degree of physical contact between the brick and clay was achieved at curing temperatures of 600°C. Poor clay-brick contact was observed in the sample that was heated to 900°C.Matte displaced the clay in the clay-brick-matte sample that was heated to 1350°C, with significant matte penetration into the brick. Less matte penetration was observed when the clay-brick-matte sample was heated to 1500°C. Less matte penetration was also observed in the claybrick- matte sample in which the clay and brick were pre-baked at 800°C, and the sample then reacted with matte at 1350°C. IntroductionFloatation concentrate from ore from the eastern Bushveld Complex of South Africa, specifically the Platreef, Merensky, and UG2 reefs, forms the feed to the Polokwane platinum smelter (Hundermark, De Villiers, and Ndlovu, 2006). The ore from the UG2 Reef has a high chromite content, which requires high operating temperatures (1500–1700°C) to avoid chromium spinel build-up in the furnace hearth. These high operating temperatures lead to matte superheats in the vicinity of 500– 600°C, which put increased demands on the refractory materials (Nelson et al., 2005).Upon tapping, the matte moves through the tap-hole, which consists of an aluminachrome refractory brick-lined tapping channel (Hundermark, De Villiers, and Ndlovu, 2006). The flow of molten matte is stopped by the injection of tap-hole clay to form a plug in the tap-hole. The tap-hole clay hardens and strengthens during curing to obtain the required hardness and refractoriness against penetration, corrosion and erosion (Nelson and Hundermark, 2014)."

Jan 1, 2016

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011