Search Documents

By J. M. Eriksen, T. Rosenqvist, H. Elstad, S. Seim, A. Hildal

The titanium industry demands high titanium feedstock for their processes. As rutile resources are limited, ilmenite has become the most important titanium source. Ilmenite smelting is an important part of upgrading ilmenite to high titanium feedstock. In the year 2005, upgrading of ilmenite by smelting, producing a slag with 80-90% Ti02, accounted for approximately 40% of the feedstock to the Ti02 pigment industry. In ilmenite smelting molten iron is produced together with a slag, which in addition to titanium oxide contains iron oxide as well as various impurity oxides of manganese, magnesium, silicon, aluminium, etc. Titanium is present mainly as Ti02 but partly also as Ti203. It is known that the concentration of Ti203 increases with decreasing concentration of FeO, but this dependency is affected by the nature of the impurity oxides. Sigurdson and Moore1 showed that slags high in CaO and MgO had a lower concentration of Ti203 than slags high in Si02 for the same amount of FeO. Pistorius2 showed in 2002 that if the impurity oxides MnO and MgO are counted, on a molar basis, as FeO, and Cr203, V203 and part of the A1203*), as Ti203, industrial slags will have a composition close to that of the M305 phase, where M denotes the elements Ti, Fe, Mn, etc, and which has the pseudobrookite structure. However, for equilibrium with liquid metallic iron he computed, by means of a computer program FACT, that the slag equilibrium composition is represented by a curved line in the ternary phase diagram FeTi03-TiO2-Ti2O3, but with a significantly higher concentration of trivalent titanium than actually observed in the industrial slags, and he discussed various mechanisms by which the slag during solidification could change its composition to a lower Ti203 content, but the possibility that the computed compositions might be wrong was not mentioned. Trane113 found in her research on titaniferous silicate slags a lower Ti3+/ Ti4+ ratio than that which is computed by the FACT program. The purpose of the present investigation was to study the equilibrium composition of Fe-Ti-O slag in equilibrium with liquid metallic iron, as well as the effects of impurities such as Si02, CaO and MgO on the slag composition. Industrial slags from TINFOS Titan and Iron KS (TTI) will also be discussed and their compositions will be plotted in the ternary phase diagram. These are slags produced from Tellnes ilmenite, quite high in magnesium and iron. Experimental In the past, equilibrium studies of the Fe-Ti-O slag system were difficult when it came to producing the slag. It was difficult to find a suitable crucible for the meltings. The highly corrosive slag would attack all known refractories, and the metal would attack metallic crucibles such as those made of platinum and molybdenum. In the present investigations the slag-metal combination was prepared in a high-frequency induction furnace with a vertically segmented water-cooled copper crucible. The crucible is shown in Figures 1 a and 1b. It was designed by the Australian Nuclear Science and Technology Organisation (ANSTO) with power from a 75 kVA high-frequency generator (750 kHz) supplied by Farfield Electronics Pty, Ltd, Australia. This enabled the slag-metal combination to be melted with turbulent stirring and is expected to be isothermal. The entire temperature gradient

Jan 1, 2007

A banquet, attended by 467 members and visitors, was held at the Wanderers Club, Johannesburg, at 8 p.m. on Friday, 21st March, 1969, to celebrate the 75th Anniversary of the founding of the Institute. Introduction of Dr Carel de Wet R. C. J. Goode (President) Dames en here: Ons het 'n aantal vooraanstaande gaste in ons midde vanaand en mnr Maxwell sal u later meer van hulle vertel. Dit is my aangename plig om u voor te stel aan sy Edele, die Minister van Mynwese, van Beplanning, en van Gesondheid, Dr de Wet en sy gade, mev de Wet. Sy Edele Dr de Wet het geen bekendstelling nodig nie-alhoewel hy ons minister vir slegs die afgelope twee jaar is, het hy reeds talle funksies van ons Mynbedryf bygewoon en het baie vriende gemaak onder ons. Hy het homself baie bemind onder ons gemaak toe hy Wes-Driefontein onlangs besoek het om hulle ondersteuning en aanmoediging aan te bied in hulle uur van nood. The Honourable Dr de Wet was born in the Free State. He is a grandson of that very famous general Christiaan de Wet, who caused so much pain to the British forces and for so many months so successfully eluded them in the Transvaal and Orange Free State. He was educated at both the Pretoria and Witwatersrand Universities. He first practised medicine at Boksburg and then moved to Vanderbijlpark, so you see he has an early association with gold mining on the Witwatersrand, and in moving to the Vereeniging-Vanderbijlpark district he became closely involved in our coal mining and metallurgical industries. South Africa's first steel was poured from a l0-ton open hearth furnace belonging to the Union Steel Corporation in Vereeniging in 1913. Dr de Wet has been mayor of Vanderbijlpark and for several years has been their member of parliament. More recently, the Honourable Dr de Wet has filled with great honour that most important office of Ambassador for the Republic of South Africa in London. At present he wears two hats, in that he is Minister of Planning and of Health, but more important is his cloak, that of Minister of Mines, which I trust offers him the greatest comfort. To fulfill these three arduous tasks must demand of him a terrific devotion to duty, and in doing this he carries on that loyal tradition of service to his fatherland so evident in his grandfather. Dames en here, dit is vir my 'n groot genoeë om Sy Edele Dr de Wette vra om 'n heildronk in te stel op die Instituut vir Mynwese en Metallurgie. Toast to the Institute of Mining and Metallurgy Dr the Honourable C. de Wet (Minister of Mines): Mr President, ladies and gentlemen, Mr President you have introduced me gracefully to this distinguished company and I am appreciative of your remarks. I am fully conscious of the responsibilities that devolve upon me as Minister of Mines in a country where mining makes so vital a contribution to economic progress and development and has, in fact, laid much of the foundation on which our present proud edifice is built. The achievements of the mining and metallurgical industry in its diversified activities arouse feelings equivalent to paternal pride, but let me speedily add that in considering any family relationship that may exist, the Minister of Mines should not be regarded in the role either of a fairy godmother or an indulgent father.

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By J. K. E. Douglas

PRESIDENTIAL ADDRESS Given by Mr J. K. E. DOUGLAS, M.Se. (Eng.) (Rand) SYNOPSIS Lime is the most widely used and the cheapest chemical alkali known to man and virtually every product we use or eat has required lime in some phase of its manufacture. Its use goes back to the earliest days of man and many ancient buildings and writings bear testimony to this. The manufacture of lime involves quarrying, crushing and screening of limestone and the burning of the sized stone in kilns of which there are several types. The earliest kilns were of very crude design and only in comparatively recent times have large capacity, automated and scientifically controlled kilns been developed. The history of the South African lime industry is largely that of the three main lime companies and their story is briefly told. No other material used in industry has a greater diversity of uses or more varied functions and lime has applications in most South African industries. The main applications are in the production of gold and uranium, iron, steel and ferrochrome, carbide, sugar and paper and for water treatment, agriculture and building. The Republic is well endowed with high quality limestone and the conclusion is drawn that many other minerals will have been exhausted before we run out of limestone with which to process them. The expansion of the lime industry has in the past kept pace with the requirements of industry and the future demand is expected to grow in parallel with the growth of these industries. Since the war this growth has been phenomenal and with our expanding populations and abundance of raw materials it should continue in the years ahead. Limiting factors are the shortage of skilled labour and the distance from export markets. Confidence is expressed that the challenges of the future will be met and that the lime industry will continue to make an important contribution to the growth and prosperity of South Africa. INTRODUCTION Lime, gentlemen, is known to all of you. Like myself, most of you have undoubtedly found it to be, on the appropriate occasion, a most pleasant flavouring for gin. But this lime, or rather its juice, was in earlier days more than just a flavouring. In the days of sail it was vital to the health of sailors as a deterrant against the scourge of all sea-going men-scurvy. It thus played a small but important role in the opening-up of trade routes around the world on which was based the original wealth of many of today's more advanced nations. I propose to address you on the subject of lime this evening, not the citrus variety I have just mentioned, but the most widely-used and cheapest alkali known to man, which, largely unsung, plays an even more vital part in modern industry than did its namesake in the development of inter-continental trade. In the time at my disposal, I propose to tell you something of the history, geology and technology of lime manufacture. Then I will briefly sketch for you the development of this industry in South Africa and indicate the role it plays in supplying the requirements of many of our important industries. Finally we will attempt to look into the future. The importance of this chemical alkali to our modern civilization is seldom fully appreciated-virtually every product we use or eat has required lime in some phase of its manufacture, either directly or indirectly. It is one of those basic materials, along with iron, coal, sulphur, salt and petroleum without which industry and, in fact, our modern way of living could not exist. Fortunately, nature has endowed the world with a plentiful supply of the limestone from which lime is derived and most countries have deposits adequate for their requirements. As a result, not only has there been little trade in lime products between countries but in the past the widespread occurrences of limestone have set a pattern of numerous small plants each serving a limited area. These plants were generally crude affairs incapable of producing a quality product. It is not surprising that, in an industry comprised of small producers with limited financial resources and in fierce competition with each other, there was little interchange of information. Technological development was therefore slow and the industry tended to be regarded as a backyard operation. Its popularity was not enhanced by the fact that lime is difficult and unpleasant to handle if proper facilities are not provided. In recent years the lime industry has undergone very radical changes to meet the more exacting requirements of today's more sophisticated consumers. Only since the war have the larger companies emerged with proper management, highly mechanized plants and a scientific approach. HISTORY Lime was one of the first chemical reagents used by man and consequently lime burning is one of the oldest of the chemical industries. The use of limestone dates back to the stone age when primitive man used limestone to build fireplaces, construct shelters and make crude tools and weapons. It is probable that lime was first discovered by him when the stone in these fireplaces disintegrated to a white powder which he could use for decorative purposes. The first recorded use of limestone was when huge blocks of limestone were used to build the pyramids of Egypt in 4,000 to 2,000 RC. It was not long after this that the beauty of marble, which is in fact a limestone, came to be appreciated and it found wide application in sculpturing and for decorative wall construction. Originally lime, mixed with sand, was used mainly as a mortar for building purposes, the earliest record of its use for chemical purposes being in 350 B.C. in a report of the wreck near Marseilles of a ship carrying a cargo of linen and lime 'for its bleaching'1. Cato mentioned the burning of lime kilns in 184 B.C. and the Romans made extensive use of both limestone and lime for highway construction. A treatise on architecture by Vitruvius who had an official position in the rebuilding of Rome under the Emperor Augustus remained for nearly two thousand

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11/2 inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219c. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: 1, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By P. J. A. Beukes, C. C. La Grange

INTRODUCTION Some years ago the authors proposed a modified procedure1 for carrying out micum index determinations2. The modifications consisted of using a drum of 50 cm internal length, i.e. half the length of the standard micum drum (a modification also adopted by the B.S.J.3), and the use of a + 25 mm coke instead of + 60 mm coke for the test. The proposed modified test and formulae for converting results obtained from it to standard micum test results and vice versa were based on the results obtained during the investigation of about 200 test cokes made in ovens of the South African Steel Industrial Corporation Limited (Iscor), the Fuel Research Institute co-operating with the experiments. Extensive testing of cokes has since been done at the Fuel Research Institute using both the standard and the modified procedures. The numerous test results obtained during this trial period fully support and strengthen the confidence originally expressed by the authors in the modified testing procedure. The scope of the modified micum index determination has in the meantime been extended by applying the testing procedure also to test cokes made in the Institute's experimental coke ovens, and also in this case the modified procedure has proved its usefulness. A difficulty is that when comparing the characteristics of cokes made in the Institute's two experimental coke ovens with each other and with those of cokes made from similar blends in commercial coke ovens, for example those of Iscor, the index values obtained invariably do not check exactly due mainly to inherent differences between the different types of oven4. For instance, resistance to abrasion of a coke made in Iscor's ovens is always appreciably higher than that of a coke made from the same blend (and having a similar moisture content) in the experimental ovens. This makes direct comparisons and the prediction of quality to be expected from commercial products, based on experimental coke oven results, difficult. It may also be added that workers in Great Britain some years ago reported a similar experience5. In the authors' opinion the main reason for the discrepancy is the relatively low height of the experimental ovens resulting in a much lower static pressure on the charge during coking than that obtaining in a commercial oven. The difficulty was pointed out and briefly discussed in a publication4 which appeared at a time when the micum test for coke evaluation had only just been introduced at the Institute, so that only B.S. shatter and abrasion test results were available for discussion in the publication. Needless to say, the introduction of the micum test by no means solved nor even alleviated the problem. On numerous occasions during the past few years the Institute has had to conduct contract investigations in its experimental coke ovens on behalf of companies which invariably desired an indication of the quality of coke likely to be obtained from certain coals or blends when coked commercially, more particularly in Iscor's type of coke ovens. It was, therefore, essential to accumulate statistical data which would enabe the prediction to be readily made. Fortunately the compilation of comparative coke-quality index values for the three types of oven under consideration has become possible as a result of coking investigations conducted in co-operation with Iscor over a number of years. During this period Iscor, on numerous occasions, kindly made available to the Institute portions of coals and blends coked in the Corporation's coke ovens, thus enabling parallel coking tests to be carried out in the Institute's experimental ovens. In this way enough statistical data became available to establish relationships between coking results obtained in Iscor's ovens and results obtained on similar coal charges in the Institute's ovens. The most practical and acceptable method of overcoming the problems of finding a suitable and simple basis enabling direct comparison between the cokes of the different origins mentioned to be made, is the assignment of descriptive arbitrary quality ratings, as indicated below, to the cokes obtained, it being argued that the quality rating assigned to coke made from a given coal or blend in the different coke ovens under standardized conditions should be the same, irrespective of differences in the index values obtained when subjecting the cokes to the usual coke evaluation tests. The system, which should enable the sponsors of coking investigations in the Institute's experimental ovens to make their own interpretations of the results obtained, is explained below. ARBITRARY QUALITY CLASSIFICATION OF COKES The Ml0m index1 (percentage material smaller than 10 mm after the test) of a blast furnace coke is a measure of its tendency towards breeze formation during handling -a low value indicating a low tendency. This is generally of greater importance under ruling South African conditions, than the M'40 index1 (percentage material larger than 40 mm after the test), which can be regarded as a measure of resistance to shatter. In fact, if the M10m value of a coke as made in Iscor's ovens is higher than about 11, the tendency of the coke to form breeze during handling and in the blast furnace is relatively so high that hardly any notice need be taken of its M'40 value, even if this is comparatively high. For this reason, therefore, much more weight should normally be assigned to Ml0m indices in the quality evaluation of cokes made from South African coking coals and blends, as the coals

The mathematical models of semivariograms can be classified according to whether or not they correspond to situations where the second order stationarity conditions are satisfied (§ 3.3.4). If second order stationarity exists, the a priori variance s2 of x (z) also exists and is finite. For large distances h such that x (z) and x (z + h) are not correlated, the semi- variogram ? (h) will reach a value equal to s2 [this is a consequence of (3.27) above]. This limiting value is called the sill C of the semivariogram, and the distance at which ? (h) reaches the sill is called the range. The range of the semi- variogram obtained from a given type of sample corresponds to the distance of influence of these samples. If only the intrinsic hypothesis is satisfied, the sample variance is an increasing function of the size of the area or volume in which the samples are located, and the semivariogram ? (h) will be a continuously increasing function of h. Remark: It will be shown in Chapter 7 that the variance s2 of x (z) in the ore body O is equal to the average value of ? (h) in O. If ? (h) is a non-decreasing function with sill C, the average value of ? (h) in O will be less than C. s2 and C will be equal only if for some values of h in O, ? (h) exceeds C. In practice, if the range of the semivariogram is small with respect to the dimensions of the ore body, the difference between C and s2 will be negligible.

Jan 1, 1978

To determine the characteristics of a mineral deposit, the usual practice is to take samples, analyse the properties of those samples and infer the characteristics of the deposit from these properties. This analysis can be done using statistical methods. In the present work we are concerned with two types of statistical approaches, classical statistics and spatial statistics. If one uses classical statistics to represent the properties of the sample values, the assumption is made that the values are realizations of a random variable. The relative positions of the samples are ignored, and it is assumed that all sample values in the mineral deposit have an equal probability of being selected. The likely presence of trends, zones of enrichment, or pay shoots in the mineralization, is ignored. The fact that two samples taken close to each other are more likely to have similar values than if taken far apart is also not taken into consideration. In contrast, spatial statistics will be used if one chooses to consider that the sample values are realizations of random functions. On this hypothesis, the value of a sample is a function of its position in the mineralization of the deposit, and the relative position of the samples is taken into consideration. The similarity between sample values is quantified as a function of the distance between samples and this relationship represents the foundation of spatial statistics. There are few situations where classical statistics can be used. The assumption that all sample values in the mineral deposit have an equal likelihood of being represented will be satisfied only if the sample values are randomly distributed, or if the sample positions are random. Sample values are in fact never randomly distributed within a mineral deposit. Further- more, geologists usually avoid taking samples at random (random sampling), as it is correctly accepted that samples located on a regular grid, or approximately on a regular grid, give more information than randomly located samples. In practice, classical statistics should be used only in the early stages of exploration, when the number of samples available is relatively small and the distances between samples are large. In these circumstances, and whenever the information available is not sufficient to permit the use of spatial statistics, application of the methods described in this chapter is justified.

Jan 1, 1978

By J. Nell

Heavy mineral deposits often contain relatively high levels of radioactive elements (thorium and uranium in particular).It is difficult to obtain clean separation of ilmenite and monazite (the main impurity mineral containing radioactive elements), and physical intergrowths of the two minerals are, in fact, not uncommon. As a result, ilmenite concentrates obtained from such deposits often contain high levels of thorium and uranium. Because of the large negative free energies of formation of ThO2and U3O8boththorium and uranium report to the slag during smelting and if an ilmenite concentrate contaminated with monazite is used to make high titania slag, the concentrations of these elements in the slag end up about 40% higher than in the ilmenite feed. Previous work, patented by RGC Mineral Sands Limited, and subsequently confirmed by Mintek, showed that radioactivity may be reduced by roasting an ilmenite concentrate with borax at 1000°C to 1100°C and leaching it with hydrochloric acid1. It is evident that the cost of an ilmenite roast/leach process will be high and there may be economic benefits in removing the radioactive elements from the slag instead (the volume of slag to be treated is smaller than the volume of ilmenite feed). To remove radioactive elements from the slag it is necessary to know how these elements occur in the slag. Inother words, the distribution of uranium and thorium between the various oxide, silicate and metallic phases in high titania slag must be determined. Once the deportment of thorium and uranium between the various phases ha sbeen determined, an appropriate process for slag purification can be developed. Test samples High-titania slag was prepared in a pilot-scale DC furnace from ilmenite concentrates with different levels of uranium and thorium. Subsequently, ten slag samples representing a range of compositions were selected for bulk chemical analysis, scanning electron microscopy and micro-analysis. The samples were crushed to a maximum particle size of 1 mm and from each sample a 20-kg batch was riffled out for analysis. Bulk chemical composition Chemical compositions of the samples selected for test work are given in Table I. TiO2, Al2O3, SiO2, MgO, MnO, FeO and V2O5were analysed by ICP-OES, Na2O, CaO andCr2O3by atomic absorption spectroscopy and U and Th by XRF (the XRF detection limit for U and Th was around 4 ppm). The ?B? series has a higher silica content than the others as a result of small silica additions that were made during smelting. All samples have elevated alumina levels as a result of furnace refractory contamination during smelting. As expected, there is an inverse relationship between the concentrations of TiO2and FeO in the samples (Figure 1).The TiO2and FeO levels are similar to the levels found in industrial slags2. Extreme conditions of reduction under which reduction of more ?refractory? oxides (e.g., chromia, magnesia, silica, alumina and even urania and thoria) might take place were not explored in the study. Note that BB1and BBB1 contain more than 7% combined silica and alumina (SiO2as a flux addition during smelting, and Al2O3from refractory contamination) and they do not fall on the general trend defined by the other samples. The U and Th concentrations of sample E2 is noteworthy. In the preparation of slag E2, monazite concentrate was added to the ilmenite to increase the concentrations of radioactive elements in the slag. This was done primarily to facilitate the detection of Th and U during the phase chemical characterization of the slag. Radioactivity measurements Gamma ray emissions from the samples were measured [ ]

Jan 1, 2007

By J. D. Koch

A 'project' is defined here as a process in which an idea is developed from its inception until either it is discarded or the product of the idea has been accepted by the ultimate user. The phases in a project, particularly the early phases, are examined, and project organization is described and contrasted with a functional line-management type of organization. Emphasis is placed on comprehensive definition, which is vitally important to the achievement of the goals of time, cost, and quality set for a project.

Jan 1, 1981

COUNCIL The following served on Council during the year under review: Office bearers: Prof D. D. Howat (President), Dr J. P. Hugo and P. W. J. van Rensburg (Vice-Presidents), V. C. Robinson (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: H. P. Carlisle, R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch and P. A. von Wielligh. Branch Chairmen: A. Bain (Witbank-Middelburg Branch), J. M. Meyer (O.F.S. Branch). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid and H. Simon (until March 1972). Ten Council meetings were held during the year with an average attendance of nineteen, and the standing committees held 27 meetings. FINANCE The annual accounts which are attached to this report show an excess of income over expenditure of R21 519. It is very gratifying to be able to report that Council's efforts to stop the depletion of our accumulated funds are meeting with success. The most important contributors to our surplus this year are symposia and colloquia, sales of publications, Company Affiliate subscriptions and the profit on the journal. While we do not expect continued profits from all these sources in the future we do feel that we are now in the process of accumulating a substantial financial foundation. This will give the Council the necessary confidence to initiate the new developments in the activities of the Institute which are now under consideration. The decision to create a new grade of membership, Company Affiliate, is dealt with elsewhere in this report. There has been a generous initial response from companies and this is the cornerstone of our improved financial expectations. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R91 and the total fund was, therefore, increased by this amount to R4 502. The balance sheet shows that the market value of quoted shares and debentures increased during the year from R9 160 to RH 331, which is R2 134 in excess of the book value. Accumulated funds now amount to RH 529 compared with R23 010 a year ago. MEMBERSHIP Sixteen Fellows, twenty Members, six Graduates, nine Associates, twelve Students and twenty-four Company Affiliates were elected during the year. One Member and two Associates were reinstated. Twelve members were admitted to retired membership. Transfers: Member to Fellow, three. Graduate to Member, seven Associate to Fellow, one. Student to Member, one. Student to Graduate, four. Student to Fellow, one. Your Council records with deep regret the death during the year of the following: Dr A. J. Orenstein (Honorary Life Fellow), R. A. Cooper, R. J. Spargo, H. Simon and F. Meyer (Life Fellows), S. D. Loxton, W. P. Arnold, G. C. Needham, W. G. Pyne-Mercier, J. Innes and O. T. Wright (Fellows), E. P. Mennell and O. B. Prentis (Members), J. Brits (Associate). After careful consideration of all the implications it was decided during the year to create a new grade of membership to be known as Company Affiliate, in order that there might be a formal and permanent channel for companies to contribute to the important work of the Institute. As recorded above, 24 companies had joined by the end of the year and many further applications have been received since. We extend a hearty welcome to all our new members. A comparative statement of membership as at 30th June, 1972, and the end of the previous year is shown in the following tabulation:-

By JOURNAL SAIMM

SYMPOSIUM ON PELLETS AND GRANULES During October 1974, the Newcastle branch of the Australasian Institute of Mining and Metallurgy is to hold a symposium on pelletizing and granulation, with particular reference to the iron ore, fertilizer, and cement industries.

Jan 12, 1973

By P. Amponsah-Mensah

Dilution of ore has a major impact on economics of a mine. The magnitude of dilution depends on mining method, stope dimensions, reef and host rock quality, wall support and drilling accuracy. The main contributing factor is the presence of very weak graphitic shear band of varying thickness in and around the reef. The reef, at Obuasi, is generally steeply dipping and open stoping is the predominant mining method. The stability of the stope walls limits the stope dimensions. Various options for allowing larger stopes for higher productivity and limiting dilution are analysed. The most economic way is to reinforce the walls with systematic cablebolt supports. This option does not only add the support cost but also requires additional cost of access development. These conflicting requirements are continually being optimised at the mine for the economics of dilution control. La dilution du minerai à un impact majeure sur l’économie d’une mine. La quantité de matériel diluant le minerai dépend de la méthode d’extraction, de la dimension des chantiers d’abattage, de la qualité du filon et de la roche mère, du support des épontes et de la précision du forage de production. Le facteur principal qui contribue à la dilution est la présence d’étroites zones cisaillées qui contiennent du graphite ayant différentes épaisseurs à l’intérieur et autour du filon. Le filon, à Obuasi, est généralement à fort pendage et la méthode d’abattage principale est par chantier long-trous. La stabilité des épontes est le facteur qui détermine la dimension des chantiers d’abattage. Differentes options ont été analysées de façon à permettre de plus larges chantiers de manière à augmenter la productivité tout en limitant la dilution. Le moyen le plus économique est de renforcer les épontes avec des cables d’acier cimentés forés de façon systématiques. Cette option n’augmente pas seulement les coûts de support mais aussi les coûts de développement. Ces besoins contradictoires sont continuellement revisés à l’opération afin d’optimiser l’économique par le contrôle de la dilution. Verdünnung des Erzes hat eine spürbare Auswirkung auf die Ekonomie einer Grube. Die Größe der Verdünnung hängt von gewinnenmethode, von den Stopemaßen, von der Reef- und Wirtsfelsenqualität, von der Wandunterstützung und von der bohrengenauigkeit ab. Der beitragende Hauptfaktor ist das Vorhandensein einer sehr schwachen graphitic Scherbandes unterschiedlichen Stärke in und um der Reef. Der Reef, bei Obuasi, taucht im allgemeinen steil ab und geöffnete Aufstemmung ist die überwiegende gewinnenmethode. Die Stabilität der Wand begrenz die Stope grösse. Verschiedene Wahlen für das Erlauben der größeren Stopes für höhere Produktivität und das Begrenzen von Erzesverdünnung werden analysiert. Die ökonomischste Weise soll die Wände mit systematischen Kableankerbolzenunterstützungen verstärken. Diese Wahl addiert nicht nur die Kosten der Unterstützung aber erfordert auch zusätzliche Kosten fuer Zugangsentwicklung. Diese kontroversen Anforderungen werden fortwährend an der Grube analysiert um die Verdünnungkontrolle zu optimieren.

Jan 1, 2003

By R. C. W. Webber-Youngman

The mining industry in South Africa faces real challenges with regard to the reduction of safety-related incidents. The purpose of this paper is to highlight the need for alternative interventions in addition to other safety improvement strategies already employed on mines. It furthermore supports an existing paradigm: incident investigations. An investigation into fatalities in the South African mining industry shows that although great progress has been achieved through the reduction in fatalities in all sectors of the industry over the last few years, more can and should be done to achieve status of ?zero harm?. Fatalities and lost time injuries on mines result not only in large financial losses, but also in disruptions of mining operations in general through Section 54 stoppages to resolve the situation. The approach of the paper is therefore not to try and prove whether there is high fatality rate and/or lost time injuries, but in what way incident reconstruction simulations (IRS) can have an impact in the future prevention of such incidents. The challenge therefore lies in the utilization of pro-active systems that would show employees the possible outcomes of being exposed to certain hazards. In real life, these incidents cannot be re-enacted and in most cases we can only learn through the previous mistakes of others. A virtual reality (VR) education and training system will enable employees to be ?exposed? to different hazards in a safe environment, and simulation, in a ?forgiving? environment, of the possible consequences of unsafe acts. According to the Occupational Safety and Health Act (OSHA), unsafe acts and unsafe conditions are indirect causes of safety-related incidents, but there are also direct causes; for example, unplanned release of energy and/or hazardous material, and basic causes, for example, management safety policies, personal factors, and environmental factors. The administrative workload associated with any incident investigation places a large burden on the investigation team, and in most cases other employees are informed through vague administrative processes what the ?real cause? for the incident/accident was. New preventative strategies are often put in place without showing the employees what the real causes of the incident/accident were. This can be mitigated through the use of interactive VR simulations/animations of the hazards that they are exposed to and how to deal with them. If VR interventions are not used as proposed by this paper, the real causes and consequences of almost all fatalities and lost time injuries may never be fully understood. This paper also emphasizes what potential impact IRS could have on the prevention of future mine incidents as part and parcel of a pro-active risk prevention strategy. The intention is therefore not to replace any other risk prevention strategies, but to visually enhance the reality of the incident. Keywords virtual reality, risk management, incident reconstruction simulations, interactive safety training, usability context analysis, mine safety.

Jun 1, 2013

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

THE BRITISH COUNCIL AWARDS 1971-1972 The British Council invites applications from permanent residents of the Republic of South Africa and South West Africa, for the following awards: SCHOLARSHIPS Scholarships are available to such permanent residents who hold university degrees or comparable professional qualifications. The scholarships are tenable for postgraduate study at universities and other educational establishments in Britain for the academic year of approximately ten months beginning 1st October, 1971. BURSARIES Bursaries are available to such permanent residents who hold university degrees or who, being already established in their professions or trades, hold other qualifications. The bursaries are tenable at British educational institutions or other suitable establishments in Britain for a course of training, study or research lasting not less than two months or more than six. The British Council may, at its discretion, bear the cost of single or return fares to Britain. The closing date for applications is 31st July, 1970. TRAVEL GRANTS Travel grants each of £300 are available in respect of journeys to Britain undertaken between 1st April, 1971 and 31st March, 1972 and are provided to facilitate visits to British universities by persons holding staff appointments or graduate research posts at South African universities. Visits must normally be of at least six months duration. The closing date for applications is 31st October, 1970. For further particulars and the relevant application forms please write stating the type of award for which you wish to apply to: The Cultural Attache, British Embassy, Pretoria. THE SECOND INTERNATIONAL CONFERENCE ON THE PROPERTIES OF LIQUID METALS Tokyo, September 1972 The Second International Conference on the Properties of Liquid Metals will be held under the auspices of The Japan Institute of Metals and The Physical Society of Japan from 3rd to 8th September, 1972 in Tokyo. The purpose of this conference is to continue and extend the efforts towards the objective of the First International Conference on the Properties of Liquid Metals at Brookhaven, 1966. The tentative Conference subjects presently planned are: Structure of Liquid Metals and Alloys; Atomic Transport Properties (Diffusion, Viscosity, etc.); Electronic States and Transport Properties; Thermodynamical Properties; Melting and Phase Transitions. Correspondence regarding the Conference and the request for the First Notice should be addressed to: Professor S. Takeuchi, Chairman of the Organizing Committee, The Research Institute for Iron, Steel and Other Metals, Tohoku University, Sendai, 980, Japan. PROCEEDINGS OF THE NINTH COMMONWEALTH MINING AND METALLURGICAL CONGRESS 1969 Volume 4 of the Proceedings of the Ninth Commonwealth Mining and Metallurgical Congress 1969- Physical and fabrication metallurgy-contains the 24 papers presented under this general heading at the Congress. Also included are discussion, authors' replies, name and subject indexes, and plenary addresses by Sir Val Duncan, O.B.E. and Sir Ronald L. Prain, O.B.E.

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015