Search Documents

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By A. Meek

This report compares the compressed air driven rocker shovel to the newly developed Warthog Non-throw development end loader. The two machines were compared on aspects such as safety, loading potential, energy efficiency and costs. The objectives of the comparison were to determine whether or not the replacement of the rocker shovel with the Warthog will be operationally and financially justifiable. The results from this study were obtained from underground observations and time studies on the machines, as well as consultations and data collection at the shaft and suppliers. This paper compares only the Warthog loader to the Trident 215 rocker shovel used at Anglo Platinum?s Brakspruit shaft and does not compare the other models of rocker shovels, which are fundamentally the same but will have different loading potentials and specifications. Cleaning times for the rocker shovel are based on underground observations at Brakspruit shaft. These times can be influenced by factors such as blasting practices, compressed air pressure and operator experience and skill. For this reason the times will most likely vary at different shafts. The Warthog cleaning times are based on manufacturer specifications and results from trial stages and therefore further work is required to confirm cleaning times achieved.

Jan 1, 2009

By D. François-Bongarçon

When it comes to sampling theory, a bad sampler is a bad sampler, no matter what, and a sampler is either bad or good. It also is of critical economic importance to tell and understand the difference, especially in a metallurgical plant. In this paper, the grand principles of Sampling Theory are first recalled, then the most popular types of sample cutters for plants are critically reviewed. It is concluded that the industry has a lot of progresses to make in that direction, although improvements usually pay for themselves very quickly.

Jan 1, 2002

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By George J. Karcas, Raimo Kuusisto, Pertti Pekkala

Ongoing Outokumpu development in Solvent Extraction and Electrowinning Technology, involving all aspects of process chemistry, equipment and control, extends over a period of close to 30 years. The development in SX started with molybdenum and rhenium, continued with zinc, manganese, cobalt and nickel and is now focusing on copper. The OutoCompact VSF? SX concept, which has been recently introduced, is a honed version of earlier VSF? technology. The Outokumpu VSF? ("Vertical Smooth Flow") SX package includes the DOP ("Dispersion Overflow Pump") units, the Spirok Mixers, the OutoCompact Settlers including their DDG ("Dispersion Depletor Gate") fences and tank farm equipment such as the LOS ("Loaded Organic Scrubbing") tank as well as the CEP ("Copper Electrolyte Purifying") tank. Although the VSF? SX package can be implemented according to several optional lay-outs, the so-called Track version has lately been introduced to the advantage of new plants. The new OutoCompact SX technology decreases the footprint of future VSF? plants. The lay-out, including plant size flexibility, have further been improved by Outokumpu?s new OutoReverse settler technology. Two of several SX plants currently under construction rely on reverse settlers in order to maximize their performance. The Outokumpu EW technology includes process know-how as well as proprietary equipment. The copper EW package consists of permanent stainless steel cathodes based on wax-less technology and lead anodes utilising polymer concrete cells with the double contact bus bar system and ventilation hoods fitted for efficient mist control. The lifting of cell hoods, as well as cathode washing, is done by the cathode pulling crane. Proper electrolyte flows and matching current density further ensure high productivity of LME grade copper cathodes.

Jan 1, 2005

By R. C. D. Phillis

The annual mine planning process is one of the most important tactical/operational steps towards achieving strategic goals. These tactical plans are part of a very comprehensive Mineral Resource Management process, with the natural sequel to planning being execution. The execution of an underground hard rock mine plan is a multi-project environment that comprises many development-construction-equipping-stoping single project paths, which are referred to as ?stoping paths?. The uncertainty that typifies execution of projects comes in the form of untimely disruptions to constituent tasks and/or project paths. Annual mining plans also include quantified objectives for occupational health and safety, production, quality, cost, employee morale, environment, and corporate social investment. Such objectives make for a highly complex environment that management must contend with?complex in the sense that all the paths and objectives have interdependent constraints. Furthermore, at the time of this paper, Sections54*and 55**of the MHSA*** put the onus on management to ensure legislative adherence. It stands to reason that planning estimates allow excess capacity?buffers?that cushions the impact of untimely disruptions. This paper concerns the fact that despite all the buffers allowed for, time, scope, and budget creeps impact on mine planning and threaten its successful execution. As a consequence, the paper deals with buffer management, the essence of Critical Chain Project Management (CCPM). Effective buffer management provided strategic (executive level) updates without losing the tactical/operational detail necessary for job card creation, especially where professional skills and experience are in short supply. Indicative bottom-line results showed CCPM to be highly effective.

Jan 1, 2011

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By L. J. Gardner

Ore pass systems play a critical role in moving broken rock from the workplace to surface, and the integrity of the ore pass excavations is crucial. Over the life of the mine, ore pass integrity deteriorates, which may eventually result in the ore pass no longer being fit for purpose. This paper presents several case studies of successful ore pass rehabilitation exercises.

Jan 1, 2006

By A. V. Peake

Continuous Mining presents an opportunity to extract reef in the stope ?continuously? by integrating the drill and blast activity using propellants or low energy charges. To date, the majority of effort spent on Continuous Mining systems has focused on developing an effective rock breaking process (micro breaking process), and to some extent, eliminating fumes and dust. The perceived benefits of applying low energy charges have been identified as: ?Concentrated mining yielding face advances of 40 to 60 m per month ?Lower stoping widths through better-controlled breaking ?Increase in the advance per blast ?Increase in labour productivity ?The potential to mine reefs where specific conditions make conventional mining uneconomic e.g. reefs with shales in the immediate hangingwall. However, the ability to successfully use low energy charges to create a ?Continuous or Semi-Continuous? mining method is dependent on overcoming the following challenges. ?Improving reliability of rock breaking. This is dependent upon achieving:? Improved drilling accuracy, and? Successful stemming or gas confinement, particularly in fractured rock ?Reducing gas and dust levels ?Reducing high costs. Through the research carried out in Future Mine, many different low energy rock breaking methods and systems were investigated. Whilst detailed results cannot be published here, the guidelines for overcoming low energy rock breaking challenges are discussed.

Jan 1, 2003

By Ishwinder Grewal, Michael Fullam

Many factors affect the overall performance of a gravity circuit beyond that of the primary gravity recovery device. It is critical to examine the gravity circuit in its entirety in order to determine the dominant operating variables that affect overall performance. Knelson has developed a mathematical model which has been used to assist in the design of gravity circuits, and in particular, in making accurate predictions of plant scale gravity recovery. More recently, inclusion of recovery by particle size class and additional data from various mine sites and research studies has made the model more robust. The model is now able to predict GRG (gravity-recoverable-gold) recoveries using various devices such as centrifugal concentrators, shaking tables, jigs and flash-flotation within the grinding circuit. The benefits derived by these recent advancements in modeling capability are two-fold; the first is as a tool to assist in circuit design and correct equipment selection and the second is as an analytical tool to help to evaluate and enhance the performance of existing gravity circuits.

Jan 1, 2006

In a gravity separation device, particle shape, size and density all play a role. The combination of these determines where each individual particle reports to in the viscous fluid, where particle crowding (solids to water ratio) also plays a role. To understand the performance of gravity separation devices in the heavy mineral industry, these particle characteristics need to be measured. There are various challenges in analysing particle density and particle size simultaneously for the purpose of quantifying gravity separator performance, not to mention particle shape. These analytical challenges include the high cost of high-density sink-float fractionation, toxicity of high-density sink-float media, inability of sink-float media to fractionate at densities greater than 4.0 g/cm3, and the time-intensive nature of these fractionations. The use of the detailed particle-by-particle output from Qemscan® particle mineral analyses (PMA) as a fast and cost-effective alternative is evaluated. The size and density outputs from the Qemscan® were employed to characterize the performance of a heavy mineral spiral concentrator as an example. Critical analytical requirements are to be addressed before the Qemscan® output data can be utilized. Keywords Gravity separator, performance, heavy minerals, Qemscan® particle mineral analysis

Jan 1, 2011

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By B. Ulrich

The basis of this paper is a compilation of work in the design and construction of copper heap leach facilities, and interviews with various heap leach operations personnel in Chile and Peru. The purpose is not to highlight specific mines and their performance, but rather to discuss geotechnical/civil features of copper heap leach facilities that function well, as well as features that do not. During the 1990s several copper heap leach facilities were brought on-line in South America. Many of these facilities have now been operational for a number of years during which time the operators have been able to monitor the performance of their heaps. This paper serves as a compilation of operators? experiences, and provides a discussion of the lessons learnt over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of inter-lift liners. This conference provides a timely update of the original paper (Burkhalter et al, 2002).

Jan 1, 2003

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By G. Bacon

The past decade has witnessed unprecedented growth in the development and implementation of solvent extraction technology in the extractive metallurgy of nickel and cobalt. Solvent extraction is proving to be a powerful tool, opening new opportunities for simpler, more cost efficient and environmentally sound metal refining processes. These advances, however, could not have been possible without the cooperative efforts between the nickel industry and the people and organizations involved with reagents, materials and equipment development and supply as well as solvent extraction research, aided by the accumulated knowledge and practical experience from the copper and uranium solvent extraction operations. This paper provides an overview of these developments and some of the challenges ahead.

Jan 1, 2002

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013