Search Documents

By M. I. Brittan

Discussion Dr R. E. Robinson (Fellow): The author must be congratulated on a very meticulous and self-contained piece of work. It is indeed a pleasure to read a paper that is so clearly and systematically laid out, and where the conclusions and the testwork conducted have been so clearly described. The paper is complete in itself, which makes it very difficult for someone who is not intimately involved in the whole Torco project to make any comments on its content. However, two points that, strictly speaking, fall outside the scope of the paper are of considerable interest. The first relates to the particle size of the material treated. In the paper, the testwork is confined to one standard particle size (minus 60 plus 100 mesh). The essential feature of the paper is to indicate that the rate-controlling reaction in the whole segregation process is the rate of reaction of the ore particles with the reducing agent and the hydrogen chloride. One wonders, therefore, to what extent this relatively slow rate of reaction is affected by the particle size of the ore itself. One imagines that the reaction must take place by contact of the hydrogen chloride with the surface of the mineral particles, and it is reasonable to suspect that the rate of diffusion of the copper ions to the surface is a relatively slow process and is thus the limiting factor in this particular rate of reaction. It is possible, for example, that the improvement obtained, when the ore is subjected to reducing conditions before the chlorination, is due to a breakdown in the crystal structure of the original particle. This breakdown is brought about by the reduction and by the consequent increase in surface area available for reaction with hydrogen chloride. Can the author indicate whether any work has been done along these lines, and whether it has been established that the reaction depends on the surface area available? The second point relates to the application of this kinetic study to the actual operation of a Torco reactor. It was once planned to feed the sodium chloride, together with the reducing agent, into the top of the segregation chamber. In the paper, the author mentions that it has now been established that the segregation chamber behaves, to all intents and purposes, as a fluidized bed, and that there is, therefore, a rapid evolution of gas in the lower regions of the chamber, which, it is imagined, displaces the gas phase rapidly. Since the reaction between sodium chloride, water vapour, and the aluminium silicates in the ore is extremely rapid, one wonders how much of the hydrogen chloride produced is removed from the reaction zone before it has had time to react with the copper minerals. The extremely low consumption of sodium chloride (which is a vital feature of the Torco process) must depend on an extremely rapid circulation of the hydrogen chloride gas to all the ore particles in the segregation chamber. One wonders, therefore, if a system for the introduction of the sodium chloride into the bottom regions of the chamber might not result in even greater efficiency in the utilization of sodium chloride. ProC D. D. Howat (Fellow): All of us who have been concerned with the study of chemical reactions at high temperatures are keenly interested in kinetics and are well aware that this is not an easy study experimentally. Dr. Brittan is to be congratulated on the development of neat experimental methods and for his full discussion of the results obtained. Although the segregation process for the extraction of copper from oxide and silicate ores has been known for almost fifty years, the fundamental chemical and physical changes involved have been little understood and the fundamental data are very scanty. The work now in progress at A.A.R.L., together with that sponsored by the Anglo American Corporation in other research institutions throughout the world, is bound to produce new fundamental data and a much more complete understanding of this rather fascinating process. It is already apparent that some of the old and well-worn chemical reactions that were postulated to occur, just cannot take place in the way which was formerly accepted. Dr Brittan's work, carefully conducted and thoroughly analyzed as it has been, still leaves us with one great outstanding problem. The thermodynamic data and the possible reactions set out in Table I (page 281) of his paper leave us asking, in complete despair, how can copper be converted into a volatile chloride in the presence of HCl, CO and carbon at temperatures about 800°C? The thermodynamics all combine to show that copper should be reduced to metal as the first step in the process. This brings us right up against the second problem. If copper were reduced to the metal how would HCI convert it to the volatile chloride? On top of these problems is the unknown reason for the very high speed of reaction between CO, HCI and the ground copper ore. Still further into the region of the unknown is the reaction by which gaseous hydrochloric acid is produced in the actual process. Perhaps Dr Brittan is feeling grateful that he doesn't have to try to explain this reaction-at this stage of the research programme at least. The results very clearly show that both CO and HCl gas are essential for rapid production of the volatile copper chloride. Dr Brittan states that 18 minutes were required to attain 83 per cent extraction with HCl gas alone and this was reduced to 4 minutes when CO was

Jan 2, 1970

By R. D. Beck

The minerals industry needs the support of al sections of the population if it is going to be able to supply the new materials required for future development. It will achieve this support only if its image is good. Perceived images of the minerals industry are examined in respect of history, technology, environment, safety, education, and economics. Concern is expressed about the low technological image of the industry and the declining number of students enrolling in minerals-related disciplines. It is concluded that it is the professionals, through institutes like The South African Institute of Mining and Metallurgy, who must take the lead in improving the image of the minerals industry. The Presidential Address gives data to support this thesis; data that, is hoped, can be used in efforts to educate people about the minerals industry.

Jan 1, 1991

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

By H. H. McGregor

SYNOPSIS Changes in the national productivity (gross national product per head of the population) have been assessed in order to derive a target figure for the required annual increase. The conclusion reached IS compared with the targets of the economic development programme of the Republic. Productivity and management structure in the gold mining industry is then analyzed together with investment in plant, machinery and equipment for rock handling purposes. The conclusion is drawn that productivity improvement does not appear to have accorded with the massive expenditures in plant and equipment, and in augmented management. The productivity of the manufacturing and construction sectors of the economy has been examined. The principal difficulty is that the main avenue of approach is the value of product divided by the total labour force. This introduces inflationary questions, and the use of a suitable deflator becomes of prime importance. Severa1 different methods of assessing the productivity improvement in the industrial sector have been used with what is regarded as a comparatively high degree of compatibility. Improvements in productivity in the manufacturing industry up to 1966 appear, from the information available, to have substantially exceeded comparable figures for the mining industry. There is however evidence that thereafter productivity of the manufacturing industry has not maintained this satisfactory rate of increase. If the economy is to achieve the planned rate of expansion, there is no doubt that greater attention to this aspect will be required in the future than has been accorded to it in the past.

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006

The problem of providing adequate thrust to manually operated rockdrills operating at air pressures of 70 lb/in2g to 80 lb/in2g with the aid of an air-leg is analyzed. It is shown that adequate thrust is provided by an air-leg or the stiff-leg if it is inclined at an angle to the floor of about 25°. However, this requires that the leg react against some support or protuberance, as the friction force between the leg and the floor is inadequate to contain the thrust. Conclusions summarizing optimum thrusts, blow frequencies, penetration rates, drill steel life and bit wear are presented.

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By C. Van Rhee

In dredging practice sand is eroded at very high flow velocities using water jets. The existing pick-up functions overestimate erosion. By taking the permeability into account conventional pick-up functions can be made suitable for high velocity erosion. This can be achieved by modifying the critical Shields parameter. The procedure is demonstrated using the pick-up function of Van Rijn. The theory is compared with experiments and agreement is good.

Jan 1, 2007

By P. Lloyd

Perceptions of disaster caused by burning fossil fuels have reached such a pitch that they seriously threaten the very future of the industry. Coal is a dirty word. A leader in Business Day(January 192009) claimed ?There is no disputing that renewable and non-polluting energy sources are preferable to the country?the true cost of so-called cheap coal-fired power stations is neither reflected nor accounted for by Eskom?the true and immediate but unacknowledged cost of continued coal mining is apparent in the catastrophic level of acidification from mining runoff of all significant natural water resources in the country?and their waters have been rendered unfit for human consumption. Air quality is in a similar state with?increases in pulmonary disease causing workforce absenteeism and compromised childhood development, among many other health problems recorded in areas polluted by coal mining.? The upshot is that our latest coal-fired power station, Kusile, is being required to use flue gas desulphurization. The costs are considerable, and the benefits minimal. Meanwhile, exports are being threatened by EU directives and an assumption that South African coal gives off excessive quantities of SOx and NOx when burned. The industry needs to arm itself with clear responses to these and similar misconceptions, and to communicate those responses loudly and clearly, if it is to survive.

Jan 1, 2011

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2 is reduced toTi2O3. One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2 reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3 phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By J. D. Wells

An account is given of the planning required for the rehabilitation of land that is to be disturbed by opencast mining, and of the preparation of rehabilitation of land that is to the Inspector of Mines. The plans Include the provisions that are to be made to allow for climatic conditions, land use, vegetation and wildlife, surface-water resources, geology and ground water, soils, land capability, rehabilitation method, location of discard dumps and slurry ponds, pollution control, and costs. . . Monitoring of the operation is the only way that the rehabilitation plan can be improved, and both monitoring and planning are essential when provision is being made for the closure of a mine.

Jan 1, 1986

By T. Dimillo, R. G. B. Pickeirng

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular ore bodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focussed on the haulages, cross cuts and raises. The non-explosive rock breaking method has many other applications, however, it is the integration with the Tunnel Digging Machine that results in the first, cost effective, Continuous Tunnelling Machine for hard rock mining.

Sep 1, 2001