Search Documents

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southernsector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite-anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only theUG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000tons at full run of mine production from the underground UG2 mine.

Jan 1, 2006

By J. L. Gaigher

A simple mineralogical regression model is described, which was devised in order to help the flotation plant cope with rapidly changing headgrades and feed mineralogy. Minerals in the feed were determined by means of quantitative X-ray diffraction and compared with plant performance parameters and flotation reagent consumption rates, using regression analysis. A mineralogical regression model for predicting recovery served to motivate flotation plant personnel and also set standards whereby flotation performance could be measured. The reagent consumption model indicated in which direction any or all of five flotation consumption rates should be altered. All practically measurable parameters, even those showing poor or no correlation, were included in the model, provision being made for the continuous update of a batch of data of 30 lines. Compared with the method of multiple linear regressions, the r2 is poorer at 0,41 (versus 0,50), but the mean standard error of estimate for both methods is identical at ± 6,6 units. The regression model is simpler than the method of multiple linear regressions, and although the accuracy of prediction is not high (41%), the mineralogical regression model proved to be successful in practice. Flotation efficiency, as measured by the mean ratio of head to tails grade, for the 9 month period after the mineralogical regression model was implemented on an hourly basis, improved from 2,8 to 3,2, which is equivalent to an improvement in average flotation recovery of 5% relative.

Jan 1, 1987

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By P. M. Swash

A mineralogical investigation of the main causes of refractoriness of some metalurgicaly complex gold ores in South Africa is reported. It is shown that this refractoriness is related to the presence of submicroscopic gold, carbonaceous material, pyrhotite, and base-metal sulphides. Gold ores can be classified according to their content of these components. Electron-microprobe analysis shows that gold occurs in arsenopyrite and pyrite, the gold contents of which can be up to 2700 gft. The gold and arsenic contents of these minerals are closely corelated. Furthermore, within zoned arsenopyrite grains, the concentration of gold closely folows that of arsenic. Mossbauer spectroscopy caried out on samples of concentrate from the Barberton area indicates that the submicroscopic gold within the sulphides is in a non-metalic form. The mineralogical examination of beneficiation products is important, since it sheds light on some fundamental aspects of the behaviour of the ore and gangue components during milling and flotation. Such basic information will lead ultimately to a better understanding of the problems in the beneficiation of these ores. Investigations have shown that the overmiling of the auriferous arsenopyrite and the disseminated nature of the sulphide mineralization are the main problems during beneficiation.

Jan 1, 1988

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987

By S. Konetschnik, E. Dreyer, A. Filzwieser

"More intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetimes, making cooling technology an important aspect of furnace operations. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start-up and operation, namely hydration problems, corrosion, and explosions. Apart from these aspects, the energy that is removed by extensive cooling cannot be recovered and is normally lost in the cooling towers.With METTOP’s new patented cooling technology it is possible to overcome the disadvantages of water by using an alternative cooling medium, namely ionic liquids (ILs). The main advantage of ILs is the fact that there is no risk of explosion should this liquid come in contact with molten metal. Furthermore, ILs can be used at higher temperatures than water - up to 200°C. This relatively high cooling medium temperature avoids hydration and corrosion problems and allows recovery of the energy by combining the ILTEC system and the organic Rankine Cycle (ORC) technology, for example.Due to the removal of the explosion risk, much higher safety standards can be achieved, particularly in critical areas such as tap-holes"

Jan 1, 2014

By D. D. Marsden

The paper briefly outlines the history of the successful development of vegetating techniques for mine-residue deposits. It seeks to place on record the major roles played by M.J. Mrost, who initiated and systematically developed the concept, and W.H. Cook, who continued the trials and successfully directed a stupendous large-scale project. The vegetating techniques currently practised are outlined, and it is concluded that vegetating is still the only surface-stabilizing technique of any significance that is employed throughout the world.

Jan 1, 1987

By D. A. Viljoen

An account is given of the development of man's interest in the recovery and working of minerals from Palaeolithic times to the present. This is followed by a discussion of future production trends for the more important minerals, and of likely technological developments in the recovery of various minerals. The crucial importance of energy minerals is stressed, as are several other factors of significance to a flourishing minerals industry: manpower, education, financial climate, Industrial health and safety, and preservation of the environment.

Jan 1, 1979

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

Past work on the ignition of methane-air mixtures by coal-cutting picks is reviewed, with special reference to the factors that contribute to ignitions and ways of reducing them. The main conclusions obtained from this review are outlined for the following aspects: mechanisms of ignition, methane concentrations, and the roles of rock types, cutting parameters, cutting tools, and water. However, many of these factors have been investigated on a qualitative, rather than on a quantitative, basis. A considerable amount of effort over a long period has been expended in this area of research. It is shown that a number of the factors influencing ignitions by machine picks have been researched adequately, but that there is still work to be done. Research is continuing in this area, being concentrated primarily upon the ignition potential of the coal-cutting pick.

Jan 1, 1985

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997